The Effect of Varying the Amount of Short Hemp Fibers on Mechanical and Thermal Properties of Wood–Plastic Composites from Biobased Polyethylene Processed by Injection Molding

Biobased HDPE (bioHDPE) was melt-compounded with different percentages (2.5 to 40.0 wt.%) of short hemp fibers (HF) as a natural reinforcement to obtain environmentally friendly wood plastic composites (WPC). These WPC were melt-compounded using a twin-screw extrusion and shaped into standard samples by injection molding. To improve the poor compatibility between the high non-polar BioHDPE matrix and the highly hydrophilic lignocellulosic fibers, a malleated copolymer, namely, polyethylene-graft-maleic anhydride (PE-g-MA), was used. The addition of short hemp fibers provided a remarkable increase in the stiffness that, in combination with PE-g-MA, led to good mechanical performance. In particular, 40 wt.% HF drastically increased the Young’s modulus and impact strength of BioHDPE, reaching values of 5275 MPa and 3.6 kJ/m2, respectively, which are very interesting values compared to neat bioHDPE of 826 MPa and 2.0 kJ/m2. These results were corroborated by dynamic mechanical thermal analysis (DMTA) results, which revealed a clear increasing tendency on stiffness with increasing the fiber loading over the whole temperature range. The crystal structure was not altered by the introduction of the natural fibers as could be seen in the XRD patterns in which mainly the heights of the main peaks changed, and only small peaks associated with the presence of the fiber appeared. Analysis of the thermal properties of the composites showed that no differences in melting temperature occurred and the non-isothermal crystallization process was satisfactorily described from the combined Avrami and Ozawa model. As for the thermal degradation, the introduction of HF resulted in the polymer degradation taking place at a higher temperature. As for the change in color of the injected samples, it was observed that the increase in fiber generated a clear modification in the final shades of the pieces, reaching colors very similar to dark woods for percentages higher than 20% HF. Finally, the incorporation of an increasing percentage of fibers also increased water absorption due to its lignocellulosic nature in a linear way, which drastically improved the polarity of the composite

Nanomechanical and dynamic mechanical properties of rubber–wood–plastic composites

This article presents the assessment of bulk and in situ mechanical properties of rubber–wood–plastic composites (RubWPC) and their correlations, aiming to obtain a thorough understanding of mechanical behaviour of RubWPC, which is an essential prerequisite in realising their optimal design and applications. Dynamic mechanical analysis results showed that the composites treated with multiple coupling agents (combination of maleic anhydride polyethylene [MAPE] and bis(triethoxysilylpropyl)tetrasulfide and combination of MAPE and vinyltrimethoxysilane) exhibited greater storage modulus than both the untreated and single coupling agent treated composites owing to their superior interfacial bonding quality. The shift of relaxation peak and T g towards higher temperatures observed in the treated composites confirmed the enhancement of interfacial interaction and adhesion. Nanoindentation analysis suggested that the composite with optimised interface (MAPE and Si69 treated) possessed better nanomechanical property (elastic modulus) due to the resin penetration into cell lumens and vessels and the reaction between cell walls and coupling agents.

Manufacturing and Characterization of Environmentally Friendly Wood Plastic Composites Using Pinecone as a Filler into a Bio-Based High-Density Polyethylene Matrix

The use of wood plastic composites (WPC) is growing very rapidly in recent years, in addition, the use of plastics of renewable origin is increasingly implemented because it allows to reduce the carbon footprint. In this context, this work reports on the development of composites of bio-based high density polyethylene (BioHDPE) with different contents of pinecone (5, 10, and 30 wt.%). The blends were produced by extrusion and injection-molded processes. With the objective of improving the properties of the materials, a compatibilizer has been used, namely polyethylene grafted with maleic anhydride (PE-g-MA 2 phr). The effect of the compatibilizer in the blend with 5 wt.% has been compared with the same blend without compatibilization. Mechanical, thermal, morphological, colorimetric, and wettability properties have been analyzed for each blend. The results showed that the compatibilizer improved the filler–matrix interaction, increasing the ductile mechanical properties in terms of elongation and tensile strength. Regarding thermal properties, the compatibilizer increased thermal stability and improved the behavior of the materials against moisture. In general, the pinecone materials obtained exhibited reddish-brown colors, allowing their use as wood plastic composites with a wide range of properties depending on the filler content in the blend.

Characterization of Irradiated Wood Plastic Composites (WPCs) Consumer Product

This research paper emphasizes the characterization of irradiated wood plastic composites for consumer product. Throughout this research, it is precisely conducted to observe the mechanical and physical properties of WPCs and their ability to fit in the market globally. The study also carried out to promote WPCs product that came naturally from renewable sources. WPCs in this research can be defined as mixture of wood that can be replaced with pineapple fiber in a polymer matrix. Composite that used in this research mainly consists of 40% polyethylene (PE), 50 % pineapple fiber and the rest is coupling agent that enhance the WPCs mixture. After undergoes several processes such making the raw sample of WPCs mixture, the WPCs were then irradiated under required dose levels of 0.5, 1, 1.5, 2, 2.5 kGy with the aid of the Gamma Cell Irradiator. Soon after, the irradiated WPCs then undergoes characterization process using Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy-Energy Dispersive X-Ray Spectroscopy (SEM-EDX). Diagnosis on the morphology of WPCs found that there was significant difference between the radiated and irradiated surfaces.