Mechanical Properties of concrete by reused coarse aggregate with substitution of different percentages instead of natural aggregate and incorporation of Glass fiber

Waste recycling is an option to mitigate the environmental impact resulting from the significant amount of debris generated by the productive activities of the construction. Thus, the aim of the research work to evaluate the use of Recycled Coarse aggregates (RCA) instead of natural coarse aggregate (NCA) in concrete ingredients with 30 MPa compressive strength. The experimental program began with the physical and particle size characterization of the Recycled Coarse aggregates (RCA), and subsequent comparison with the properties of the natural coarse aggregate (NCA). Based on the knowledge of these properties, the production stage began of concretes. Different procedures and literature have been studied in order to achieve the strength of concrete up to 30Mpa by incorporated glass fiber (2 % by addition of cement). It was also the influence of the use of different contents (0, 10%, 20%, 50%, and 100%) of Substitution of natural coarse aggregate by the recycled coarse concrete aggregate in the properties of the fresh and hardened state of concrete. Regarding the strength, parameters increased gradually proportional to the amount of RCA in the concrete from 10 to 20% and decrease strength to the amount of RCA in the concrete from 50 to 100% Substitution of natural coarse aggregate (NCA) in concrete

Aerosol delivery through high flow nasal cannula compared to biphasic positive airway pressure, at two different pressure: an in-vitro study

Background Both non-invasive ventilation and high flow oxygen therapy are preferred over low flow oxygen therapy in many conditions. Nebulizers, for aerosol delivery, can be used within them without interrupting the circuit. The present study aimed to compare the efficiency of drug delivery within high flow nasal cannula (HFNC) and biphasic positive airway pressure (BiPAP) ventilation mode using two different inspiratory positive airway pressures. The aerosol delivery was examined in HFNC system at low flow, 5 L min−1, and BiPAP non-invasive ventilation under 2 different pressures [high pressure; inspiratory positive airway pressure/expiratory positive airway pressure (IPAP/EPAP) of 20/5 cm water, and low pressure; IPAP/EPAP of 10/5 cm water]. The total inhalable dose (TID) was measured by inserting an Aerogen Solo nebulizer installed with 1 mL salbutamol respiratory solution (5000 μg mL−1) within the circuit, and the salbutamol was collected on an inhalation filter placed in a filter holder connected to a breathing simulator. The breathing simulator was adjusted at a tidal volume of 500 mL, respiratory rate of 15 breaths min−1, and inhalation to exhalation (I:E) ratio of 1:1 for the adult setting. In each technique of the three (HFNC, and low, and high-pressures BiPAP), TID was determined 5 times (n = 5). For particle size characterization, cooled Anderson Cascade Impactor (ACI) was inserted instead of the inhalation filter and the breathing simulator with the same scheme. In each technique of the three, particle size characterization was determined 3 times (n = 3). Results The BiPAP mode at low inspiratory pressure had the highest TID, followed by HFNC at flow 5 L min−1, then BiPAP mode at high inspiratory pressure. There was a significant difference only between low and high inspiratory pressure modes of BiPAP mode. Low-inspiratory pressure BiPAP delivered the highest mean ± SD fine particle dose (FPD). It was significantly higher than that delivered in high inspiratory pressure BiPAP, and HFNC. Also, FPD in HFNC was significantly higher than that in high inspiratory pressure BiPAP. HFNC system had the smallest mass median aerodynamic diameter (MMAD) and the highest FPF followed by low then high inspiratory pressure BiPAP. Conclusions Increasing the inspiratory positive airway pressure in BiPAP, from 10 to 20 cm water, decreased the total inhalable dose and FPF nearly by half. Low inspiratory pressure BiPAP delivered the highest TID and FPD. The HFNC system at low oxygen flow resulted in the least MMAD, and the highest FPF. Using HFNC delivered a TID that was non-significant from that delivered by low inspiratory pressure BiPAP. Graphical Abstract

Grain Size Characterization of Ceramic Matrix Composites

In the field of materials science, the mesoscopic geometry of materials is of great significance for the research and development of materials and materials. This paper mainly focuses on the image data of existing ceramic matrix composites, and studies the characterization method of grain image of ceramic matrix, which realizes the accurate characterization of grain size. It has important practical research on the mesostructure of ceramic matrix composites. Value. Taking the SEM grain image of 5μm resolution of self-toughening silicon nitride (Si3N4) ceramic as an example, the grain image is segmented by median filtering, image binarization and watershed algorithm, and then used to directional bounding box (Oriented). The Bounding Boxes, OBB) algorithm finds the rectangular outline bounding box of the grain, enabling accurate measurement and statistics of the grain size.

Production and Characterization of Sumac PlantCrystals: Influence of High-Pressure Homogenization on Antioxidant Activity of Sumac (Rhus coriaria L.)

Oxidative stress diseases are usually treated or prevented by using antioxidants from natural or artificial sources. However, as a sustainable source of phytochemicals, plants got a renewed interest in obtaining their active agents using green extraction technologies, i.e., sustainable extraction techniques that reduce energy consumption, use renewable sources and result in less post-extraction wastes. The high-pressure homogenization (HPH) technique was introduced into the food industry since it was invented in 1900 to homogenize milk and later to produce fruit juices with a longer shelf-life without preservatives. Recently, HPH was introduced as an eco-friendly method to nanomill plants for improved extraction efficacy without using organic solvents. In this study, sumac was used as an antioxidants-rich spice model to investigate the effects of HPH on its antioxidant capacity (AOC). Sumac was rendered into PlantCrystals by using HPH. Particle size characterization proved the presence of submicron-sized particles (about 750 nm). Thus, HPH was able to produce sumac PlantCrystals and increased the AOC of bulk sumac by more than 650% according to the ORAC (oxygen radical absorbance capacity) assay. The polyphenol and flavonoid contents showed higher values after HPH. Interestingly, the DPPH (1,1-diphenyl-2-picrylhydrazyl) assay also showed a well improved AOC (similar to ascorbic acid) after HPH. In fact, in this study, the PlantCrystal-technology was demonstrated to cause an efficient cell rupture of the sumac plant cells. This caused an efficient release of antioxidants and resulted in sumac PlantCrystals with a 6.5-fold higher antioxidant capacity when compared to non-processed sumac bulk material.

Synthesis of crystalline and amorphous, particle-agglomerated 3-D nanostructures of Al and Si oxides by femtosecond laser and the prediction of these particle sizes

We report a single step technique of synthesizing particle-agglomerated, amorphous 3-D nanostructures of Al and Si oxides on powder-fused aluminosilicate ceramic plates and a simple novel method of wafer-foil ablation to fabricate crystalline nanostructures of Al and Si oxides at ambient conditions. We also propose a particle size prediction mechanism to regulate the size of vapor-condensed agglomerated nanoparticles in these structures. Size characterization studies performed on the agglomerated nanoparticles of fabricated 3-D structures showed that the size distributions vary with the fluence-to-threshold ratio. The variation in laser parameters leads to varying plume temperature, pressure, amount of supersaturation, nucleation rate, and the growth rate of particles in the plume. The novel wafer-foil ablation technique could promote the possibilities of fabricating oxide nanostructures with varying Al/Si ratio, and the crystallinity of these structures enhances possible applications. The fabricated nanostructures of Al and Si oxides could have great potentials to be used in the fabrication of low power-consuming complementary metal-oxide-semiconductor circuits and in Mn catalysts to enhance the efficiency of oxidation on ethylbenzene to acetophenone in the super-critical carbon dioxide.

Synthesis of crystalline and amorphous, particle-agglomerated 3-D nanostructures of Al and Si oxides by femtosecond laser and the prediction of these particle sizes

We report a single step technique of synthesizing particle-agglomerated, amorphous 3-D nanostructures of Al and Si oxides on powder-fused aluminosilicate ceramic plates and a simple novel method of wafer-foil ablation to fabricate crystalline nanostructures of Al and Si oxides at ambient conditions. We also propose a particle size prediction mechanism to regulate the size of vapor-condensed agglomerated nanoparticles in these structures. Size characterization studies performed on the agglomerated nanoparticles of fabricated 3-D structures showed that the size distributions vary with the fluence-to-threshold ratio. The variation in laser parameters leads to varying plume temperature, pressure, amount of supersaturation, nucleation rate, and the growth rate of particles in the plume. The novel wafer-foil ablation technique could promote the possibilities of fabricating oxide nanostructures with varying Al/Si ratio, and the crystallinity of these structures enhances possible applications. The fabricated nanostructures of Al and Si oxides could have great potentials to be used in the fabrication of low power-consuming complementary metal-oxide-semiconductor circuits and in Mn catalysts to enhance the efficiency of oxidation on ethylbenzene to acetophenone in the super-critical carbon dioxide.

Synthesis and Nano-Sized Characterization of Bioactive Oregano Essential Oil Molecule-Loaded Small Unilamellar Nanoliposomes with Antifungal Potentialities

The development of greener nano-constructs with noteworthy biological activity is of supreme interest, as a robust choice to minimize the extensive use of synthetic drugs. Essential oils (EOs) and their constituents offer medicinal potentialities because of their extensive biological activity, including the inhibition of fungi species. However, their application as natural antifungal agents are limited due to their volatility, low stability, and restricted administration routes. Nanotechnology is receiving particular attention to overcome the drawbacks of EOs such as volatility, degradation, and high sensitivity to environmental/external factors. For the aforementioned reasons, nanoencapsulation of bioactive compounds, for instance, EOs, facilitates protection and controlled-release attributes. Nanoliposomes are bilayer vesicles, at nanoscale, composed of phospholipids, and can encapsulate hydrophilic and hydrophobic compounds. Considering the above critiques, herein, we report the in-house fabrication and nano-size characterization of bioactive oregano essential oil (Origanum vulgare L.) (OEO) molecules loaded with small unilamellar vesicles (SUV) nanoliposomes. The study was focused on three main points: (1) multi-compositional fabrication nanoliposomes using a thin film hydration–sonication method; (2) nano-size characterization using various analytical and imaging techniques; and (3) antifungal efficacy of as-developed OEO nanoliposomes against Trichophyton rubrum (T. rubrum) by performing the mycelial growth inhibition test (MGI). The mean size of the nanoliposomes was around 77.46 ± 0.66 nm and 110.4 ± 0.98 nm, polydispersity index (PdI) of 0.413 ± 0.015, zeta potential values up to −36.94 ± 0.36 mV were obtained by dynamic light scattering (DLS). and spherical morphology was confirmed by scanning electron microscopy (SEM). The presence of OEO into nanoliposomes was displayed by attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectroscopy. Entrapment efficiency values of 79.55 ± 6.9% were achieved for OEO nanoliposomes. In vitro antifungal activity of nanoliposomes tested against T. rubrum strains revealed that OEO nanoliposomes exhibited the highest MGI, 81.66 ± 0.86%, at a concentration of 1.5 µL/mL compared to the rest of the formulations. In summary, this work showed that bioactive OEO molecules with loaded nanoliposomes could be used as natural antifungal agents for therapeutical purposes against T. rubrum.