Evaluation of Corrosion Behavior by Measuring Passivation Current Density of Dental Implant Coated with Bioceramic Materials

Background. This paper reports the corrosion behavior of uncoated commercially pure titanium and Ti-6Al-4V samples and these coated with hydroxyapatite, partial stabilized zirconia (PSZ), and the mixture of partial stabilized zirconia and hydroxyl-apatite by measuring passivation current density and see if there are any differences between them using electrochemical polarization tests in 37°C Hank’s solution. Materials and Methods. The electrophoretic deposition method (EPD) was elected to keep the coating materials which are HA, PSZ, and the mixture of 50% HA and 50% PSZ on Cp Ti and Ti-6Al-4V alloy samples. The electrochemical corrosion test was achieved by exposing the coated and uncoated samples to Hank’s solution which prepared in the laboratory and measuring the polarization potential, passivation current density, and the open circuit potential for all samples. Results. The results indicated that the passivation current density for all Cp Ti and Ti-6Al-4V alloy groups that coated with HA, PSZ, and with mixture of 50/50 HA and PSZ was less than uncoated groups. There are no significant differences between all Cp Ti groups when compared with all Ti-6Al-4 V alloy groups. The open circuit potential (OCP) for both Cp Ti and Ti -6Al -4V samples was in the following sequence PSZ > HA > mixture of HA and PSZ > uncoated . Conclusions. Coating significantly decreased the passivation current density of Cp Ti and Ti-6Al-4V alloy.

Characteristics of Passive Films Formed on As-Cast Ti–6Al-4V in Hank’s Solution Before and After Transpassivation

In this work, the characteristics of passive films formed on as-cast Ti-6Al-4V before and after transpassivation by electrochemical methods will be studied. A simulated body fluid of Hank’s solution was used as the electrolyte in this work. According to the potentiodynamic polarization test, the passivation range, transpassive range, and repassivation range of as-cast Ti-6Al-4V were obtained. Afterward, the potentiostatic polarization was employed to passivate the Ti-6Al-4V in both passivation and repassivation ranges. Electrochemical impedance spectroscopy (EIS) was used to analyze the characteristics of formed passive films. Different electrochemical behavior of as-cast Ti–6Al-4V is found in passivation and repassivation ranges. The passivation current density of the sample in the repassivation range is significantly larger than that in the passivation range. Meanwhile, the growth rate of passive film in the repassivation range is also greater than that in the passivation range. Although the sample shows a higher charge transfer impedance in the repassivation range, metastable pitting corrosion is also observed, indicating the formation of the unstable passive film. Such results advance the understanding of as-cast Ti-6Al-4V polarized under different potentials for potential biomedical applications.

Corrosion Behavior of As-Cast Ti–10Mo–6Zr–4Sn–3Nb and Ti–6Al–4V in Hank’s Solution: A Comparison Investigation

Newly developed Ti–10Mo–6Zr–4Sn–3Nb has fascinating mechanical properties to be used as a biomedical material. However, there is still a lack of investigation focusing on the corrosion behavior of Ti–10Mo–6Zr–4Sn–3Nb. In this work, the microstructure and corrosion behavior of as-cast Ti–10Mo–6Zr–4Sn–3Nb was investigated by optical microscopy, X-ray diffraction, and electrochemical measurements. Hank’s solution was used as the electrolyte. A classical as-cast Ti–6Al–4V was used as reference. The results showed that Ti–10Mo–6Zr–4Sn–3Nb has a higher corrosion potential and a lower corrosion current density compared with Ti–6Al–4V, indicating better corrosion resistance. However, after applying anodic potentials, Ti–10Mo–6Zr–4Sn–3Nb shows larger passivation current density in both potentiodynamic polarization and potentiostatic polarization tests. This is because more alloying elements contained in Ti–10Mo–6Zr–4Sn–3Nb trigger the production of a larger number of oxygen vacancies, resulting in a higher flux of oxygen vacancy. This finding illustrates that the passive film on Ti–10Mo–6Zr–4Sn–3Nb is less protective compared with that on Ti–6Al–4V when applying an anodic potential in their passivation range.

Effect of heat on microstructural, mechanical and electrochemical evaluation of tungsten inert gas welding of low-nickel ASS

Purpose The purpose of the study is to evaluate Cr-Mn ASS weld using different heat inputs for its microstructure, mechanical properties and electrochemical behavior. The microstructural examination used optical and scanning electron microscopy. It was observed that ferrite content decreases with increasing heat input. The length of dendrites, inter-dendritic space and volume of lathy ferrite increase with increasing heat input. The increasing heat input caused grain coarsening near the fusion boundary and produced wider heat-affected zone (HAZ). It also decreases hardness and tensile strength. This is attributed to formation of more δ ferrite in the weld. The electrochemical evaluation suggested that the δ ferrite helps in improving the pitting potential in 3.5 per cent NaCl solution saturated with CO2. Whereas in 0.5-M H2SO4 + 0.003-M NaF solution, higher passivation current density was observed because of dissolution of dferrite. The interphase corrosion resistance decreased with increasing heat input. Design/methodology/approach The Cr-Mn austenitic stainless steel or low-nickel ASS was procured in form of 3-mm sheets in rolled condition. The tungsten inert gas welding was performed at three different heat inputs (100 A, 120 A and 140 A), argon as shielding gas with a flow rate of 15 L/min. Different welded regions were observed using optical microscope and scanning electron microscope. Electrochemicals test were performed in solutions containing 3.5 per cent NaCl with saturated CO2 solution and 0.5 M sulfuric acid + 0.003 M NaF at a scan rate of 0.1667 mV/s at room temperature (30 °C ± 1 °C) using a potentiostat. Findings The test steel Cr-Mn ASS is suitable with the selected electrode (308 L) and it produces no defects. Vermicular ferrite and lathy ferrite form in welds of various heat inputs. The increase in heat input reduces the formation of lathy ferrite. The width of HAZ and un-mixed zone increases with increase in heat input. The weld zone of low heat input (LHI) has the highest hardness and tensile strength because of higher δ ferrite content and small grain size in the weld zone. The hardness at high heat input (HHI) is found to be lowest because of grain coarsening in the weld. With increase in δ ferrite, the pitting resistance increases. In 0.5-M sulfuric acid + 0.003-M NaF, the increase in ferrite content reduces the passivation current density. Interphase corrosion resistance increases with increase in δ ferrite content as higher per cent degree of sensitization was observed in LHI welds as compared to medium heat input and HHI welds. Originality/value This work focuses on welding of ASS by tungsten inert gas welding at different heat inputs. Welding is a critical process for joining metals in most of the fabrication industries and proper heat input is required for getting desired microstructure in the weld metal. This would highly affect the strength and corrosion behavior of the alloy. This paper would give an understanding of how the change in heat input by tungsten inert gas welding affects the microstructural and corrosion behavior in the weld metal.

Electrochemical Corrosion Behaviors of CuZrHfTi Bulk Metallic Glasses in NaOH Solution

The electrochemical corrosion behaviors of Cu60Zr30-xHfxTi10(x=10,15,20) bulk metallic glasses (BMGs) were investigated in 3 mol/L NaOH solution by potentiodynamic polarization experiments and electrochemical impedance spectroscopy (EIS). The results showed that the BMGs had sufficient corrosion resistance in NaOH solution. The anodic showed grading passivation character, and the passivation current density were very low. The corrosion resistance changed with Hf content changing. The passivation current density of Cu60Zr15Hf15Ti10 alloy was lowest and the charge transfer resistance was largest, which means the best corrosion resistance for CuZrHfTi BMGs. Corrosion mechanisms were not changed, while the corrosion resistance decrease after crystallized for the BMGs.

Effect of Heat Treatment on Corrosion Behavior of Alloy 690 and Alloy 693 in Simulated Nuclear High-Level Waste Medium

Nickel-based alloys are being considered as candidate materials for the storage of high-level waste generated from the reprocessing of spent nuclear fuel. In the present investigation, Alloy 690 (UNS N06690) and Alloy 693 (UNS N06693) were assessed using the potentiodynamic anodic polarization technique for the corrosion behavior in the solution-annealed and sensitized conditions, in 3 M nitric acid (HNO3) and simulated high-level waste (HLW) at 25°C and 50°C. From the results of the investigation, it was found that the polarization curves for the solution-annealed specimens were characterized by a long passive range and low passivation current density, at 25°C. Increasing solution temperature to 50°C led to a corresponding increase in corrosion potential as well as passivation current density. The solution-annealed specimen showed improved corrosion resistance compared to the sensitized specimen in both media, for both alloys. Double-loop electrochemical potentiokinetic reactivation (DL-EPR) test was carried out for both solution-annealed and sensitized Alloy 690 and Alloy 693 in 0.5 M sulfuric acid (H2SO4) containing 0.0001 M potassium thiocyanate (KSCN), to measure the degree of sensitization (DOS). Microstructural examination was carried out by optical microscopy and scanning electron microscopy (SEM) after electrolytic etching. The results of the present investigation are discussed in the paper.

A Comparison Of The Corrosion Behaviour Of Nanocrystalline And Normal Crystalline Nickel

ABSTRACTThe effect of grain size on the corrosion behaviour of nickel in 2N sulphuric acid is evaluated by potentiodynamic testing and characterization of the corrosion morphology for grain sizes ranging from 100μ to 32nm. The influence of the grain boundary component on key electrochemical parameters (free corrosion potential, passivation current density and potential, transpassive dissolution rate) is discussed.

On the Passivity of Iron★

Descriptions are given of the various phenomena associated with the passivation and reactivation of iron in concentrated nitric acid. Covered are apparent and true passivation potential, apparent and true passivation current density, passivity producing and passivity maintaining current density. Information is given also on equivalent current density in a redox system, the role of nitrous acid in passivation by concentrated nitric acid, the corrosion of passive iron, refractoriness toward activation, rhythms and activity waves.