Tailoring hydroxyapatite microspheres by spray-drying for powder bed fusion feedstock

The present work deals with a study on the physical characteristics of hydroxyapatite microspheres produced by spray-drying process through different operating conditions. Obtained hydroxyapatite microspheres will be used as powder feedstock in powder bed selective laser processing additive manufacturing technologies where the flowability and the particle size distribution of the powder feedstock is of special importance. Spray air pressure and solid content of the slurries were the most influent parameters to control the final particle size distribution, while higher air pressure and temperatures gave the higher process recovery rate. The use of polyvinyl alcohol as organic binder increased the granules strength. The produced hydroxyapatite microspheres were found to fulfil the powder bed selective laser processing feedstock requirements, keeping the physico-chemical properties of the material. These promising results confirm the use of a spray dryer as an efficient method for the production of hydroxyapatite microspheres for powder bed selective laser processing.

Nanoparticle Additivation Effects on Laser Powder Bed Fusion of Metals and Polymers—A Theoretical Concept for an Inter-Laboratory Study Design All Along the Process Chain, Including Research Data Management

In recent years, the application field of laser powder bed fusion of metals and polymers extends through an increasing variability of powder compositions in the market. New powder formulations such as nanoparticle (NP) additivated powder feedstocks are available today. Interestingly, they behave differently along with the entire laser powder bed fusion (PBF-LB) process chain, from flowability over absorbance and microstructure formation to processability and final part properties. Recent studies show that supporting NPs on metal and polymer powder feedstocks enhances processability, avoids crack formation, refines grain size, increases functionality, and improves as-built part properties. Although several inter-laboratory studies (ILSs) on metal and polymer PBF-LB exist, they mainly focus on mechanical properties and primarily ignore nano-additivated feedstocks or standardized assessment of powder feedstock properties. However, those studies must obtain reliable data to validate each property metric’s repeatability and reproducibility limits related to the PBF-LB process chain. We herein propose the design of a large-scale ILS to quantify the effect of nanoparticle additivation on powder characteristics, process behavior, microstructure, and part properties in PBF-LB. Besides the work and sample flow to organize the ILS, the test methods to measure the NP-additivated metal and polymer powder feedstock properties and resulting part properties are defined. A research data management (RDM) plan is designed to extract scientific results from the vast amount of material, process, and part data. The RDM focuses not only on the repeatability and reproducibility of a metric but also on the FAIR principle to include findable, accessible, interoperable, and reusable data/meta-data in additive manufacturing. The proposed ILS design gives access to principal component analysis (PCA) to compute the correlations between the material–process–microstructure–part properties.

Effect of the Process Atmosphere Composition on Alloy 718 Produced by Laser Powder Bed Fusion

The detrimental effect of nitrogen and oxygen when it comes to the precipitation of the strengthening γ’’ and γ’ phases in Alloy 718 is well-known from traditional manufacturing. Hence, the influence of the two processing atmospheres, namely argon and nitrogen, during the laser powder bed fusion (L-PBF) of Alloy 718 parts was studied. Regardless of the gas type, considerable losses of both oxygen of about 150 ppm O2 (≈30%) and nitrogen on the level of around 400 ppm N2 (≈25%) were measured in comparison to the feedstock powder. The utilization of nitrogen as processing atmosphere led to a slightly higher nitrogen content in the as-built material—about 50 ppm—compared to the argon atmosphere. The presence of the stable nitrides and Al-rich oxides observed in the as-built material was related to the transfer of these inclusions from the nitrogen atomized powder feedstock to the components. This was confirmed by dedicated analysis of the powder feedstock and supported by thermodynamic and kinetic calculations. Rapid cooling rates were held responsible for the limited nitrogen pick-up. Oxide dissociation during laser–powder interaction, metal vaporization followed by oxidation and spatter generation, and their removal by processing atmosphere are the factors describing an important oxygen loss during L-PBF. In addition, the reduction of the oxygen level in the process atmosphere from 500 to 50 ppm resulted in the reduction in the oxygen level in as-built component by about 5%.