Research on the Inertial Migration Characteristics of Bi-Disperse Particles in Channel Flow

The inertial focusing effect of particles in microchannels shows application potential in engineering practice. In order to study the mechanism of inertial migration of particles with different scales, the motion and distribution of two particles in Poiseuille flow are studied by the lattice Boltzmann method. The effects of particle size ratio, Reynolds number, and blocking rate on particle inertial migration are analyzed. The results show that, at a high blocking rate, after the same scale particles are released at the same height of the channel, the spacing between the two particles increases monotonically, and the change in the initial spacing has little effect on the final spacing of inertial migration. For two different size particles, when the smaller particle is downstream, the particle spacing will always increase and cannot remain stable. When the larger particle is downstream, the particle spacing increases firstly and then decreases, and finally tends to be stable.

Effect of the Metallic Aging on the Microstructure and Mechanical Properties of Titanium Alloy

ABSTRACTDifferent aging heat treatments were performed in a Titanium alloy using as aging media metallic baths in comparison to typical furnace aging. As a first step, a Duplex Aging (DA) consisted of solubilization followed by quenching to room temperature after aging heat treatment in different metallic baths (Zn, Sn and Bi). A second procedure was Alternative Aging (AA) which consisted of solubilization and direct aging inside three different aforementioned baths. Microstructural aging variations begins at half hour until 30 h at 550°C inside metallic bath of Zn, Sn or Bi. Both kinds of aging promoted a microstructural variation and so on microhardness values. Microstructural analysis by Optical Microscopy showed a structural refinement after AA treatment. The highest hardness value of 375 HVN was achieved in Alternative Aging with Zn bath, which was found to be dependent on laminar α phase refining. Moreover, after AA treatment for 0.5, 1, 2, 3, 4, 10 and 30 h at 550°C in the metallic bath of Zn and Sn, the results indicated similar hardness values in different times, resulting in the fastest kinetic for Sn metallic bath at 2 h compared to that 4 h in Zn metallic bath. The observed increase in micro-hardness is not very attractive, it is recommended to use large aging times in order to stabilize final spacing of microstructural features in AA treatment.

Plant Population, Transplant Size, and Variety Effect on Transplanted Short-day Onion Production

Onions (Allium cepa) produced in southeastern Georgia's Vidalia-growing region are primarily grown from on-farm–produced bareroot transplants, which are usually sown the end of September. These transplants are pulled midwinter (November–January) and are reset to their final spacing. This study was to evaluate transplant size and spacing effects on yield and quality of onions. Large transplants (260–280 g per 20 plants) generally produced the highest yield. Medium transplant size in the range of 130 to 150 g per 20 plants produced satisfactory yield while maintaining low numbers of seedstems (flowering) and doubled bulbs, which are undesirable characteristics. Smaller transplant size (40–60 g per 20 plants) have reduced yields and lower numbers of seedstems and double bulbs. Increasing plant population from 31,680 to 110,880 plants/acre can increase yield. In addition, plant populations of 110,880 plants/acre can increase yields compared with 63,360 plants/acre (industry standard), but only when environmental conditions favor low seedstem numbers. Seedstems can be high because of specific varieties, high plant population, or more importantly, in years with environmental conditions that are conducive to their formation. ‘Sweet Vidalia’ was the only variety that had consistently reduced quality and high numbers of seedstems. ‘Sweet Vidalia’ has a propensity for high seedstem numbers, which may have influenced results with this variety. A complete fertilization program that included 133 or 183 lb/acre nitrogen did not affect onion yield, regardless of variety or population density.

Simulation of Nanofibers Movement for Near-Field Electrospinning

NFES is a new and simple way to realize precision-positioning of nanofiber. A model on NFES nanofiber movement is built to analyze the effects of the existed nanofibers which have been collected on the substrate, on the nanofiber’s dropping movement. During electrospinning nanofiber is affected by the electric field force, Coulomb repulsive force, air resistance force gravity and so on. The influence of parameters on the deposition behavior of as-spun nanofiber is discussed. The simulation results show that (i) with charge density increasing, the final spacing between mass center of nanofibers A and B (FSAB) increases and the movement distance of center-of-mass of nanofiber B (MDB) decreases first and then increases; (ii) FSAB increases with applied voltage, but decreased in narrow range with concentration of PEO increasing; (iii) FSAB decreased with the initial spacing between mass center of nanofibers A and B (ISAB) increasing, and then it increases after reaching the minimum. So does ISAB to DMB. This simulation model would improve the controlling of nanofiber in NFES.

Sowing Date, Transplanting Date, and Variety Effect on Transplanted Short-day Onion Production

Onions (Allium cepa) produced in southeastern Georgia's Vidalia-growing region are primarily grown from on-farm produced bareroot transplants, which are usually sown at the end of September. These transplants are pulled midwinter (November to January) and reset to their final spacing. This study was to evaluate sowing date, transplanting date, and variety effect on yield and quality of onions. Beginning in the first week of November, onions can be transplanted until the end of December with reasonable yield and quality. For example, in the 2003–04 season, total yield of onions transplanted on 22 Dec. 2003 did not differ from any onions transplanted on earlier dates in November or December. In the 2004–05 season, onions transplanted on 20 Dec. 2004, had lower total yield than onions transplanted in November, but were not different from onions transplanted on 4 Jan. 2005. The propensity of some varieties to form double bulbs can be reduced with later sowing and transplanting dates. Sowing the first week of October rather than the fourth week of September and transplanting in December rather than November can reduce double bulbs in some varieties.

DIRECT SEEDING VIDALIA ONIONS

The majority of Vidalia onions are produced as a transplanted crop. Seeding in high density plantings in September is followed 8 to 10 weeks later by transplanting to final spacing. This practice is labor intensive and expensive. Direct seeding would save on labor, cost, and time. Traditionally, transplanting has been done because of better winter survival, more uniform stands, and better irrigation management during seedling emergence. Beginning 5 years ago, we began evaluating direct seeding onions. Initially, seedstems (bolting) and lack of uniform stand establishment were the main problems. Sowing in September resulted in almost 100% seedstems and using a belt planter with raw seed resulted in poor singulation for uniform stand establishment. Mid-October ultimately proved to be the best time for sowing Vidalia onion seed. Earlier sowing resulted in more seedstems and later planting did not give the plants sufficient time to grow resulting in later stand loss during cold winter temperatures. Using polymer coated seed and a precision vacuum planter resulted in uniform, even stand establishment. Fertilizer requirements are almost half with direct seeded onions compared to transplanted onions with a reduction in the need for fungicides and herbicides. We have established direct seeded onions both with drip irrigation and overhead irrigation. There was concern that center-pivot irrigation would not be able to sufficiently irrigate fields during seedling establishment with the frequent hot fall days we experience. Since this work was initiated several growers have successfully produced direct seeded onions under center-pivot systems. Direct seeding Vidalia onions requires attention to detail because there is only one opportunity to get it right. Timing is also critical particularly with planting date and herbicide application.

Genetic improvement of sugar maple for high sap sugar content. I. Clone selection and seed orchard development

A grafted seed orchard of Acersaccharum Marsh, was established in Ohio in 1957 as part of a program of genetic improvement of sugar yield. During the 3rd decade, the orchard trees averaged 4.2% sap sugar. Although environmental sources of variance in sugar concentration were large, clonal differences were evident and generally consistent over the years; the clone × year interaction was negligible. Sap sugar concentration varied from year to year, but after an increase coinciding with early crown development in the 1st decade, there was no upward or downward trend with age. Inclusion of one seedling family in the orchard made it possible to obtain an approximation of within-family variance by comparison with within-clone variance. It was estimated to be about one-third of total family variance. The clone–family comparison also suggested that about 11% of total clonal variance was a rootstock effect. Sap tests over 3 years in a plantation of seed-orchard offspring showed that an initial thinning to an average 6.3 × 6.3 m spacing would leave trees with an average 4% sap sugar concentration. At final spacing the concentration would be higher. Only a few clones in the orchard produced medium or heavy crops of male or female flowers prior to age 27, but those from which seed was collected in early years averaged at least 4% sap sugar. All clones and the seedling family flowered by age 27.