Rational Use of Novel Technologies: A Comparative Analysis of the Performance of Several New Food Preservation Technologies for Microbial Inactivation

Author(s):  
Stella M. Alzamora ◽  
Jorge Welti-Chanes ◽  
Sandra N. Guerrero ◽  
Paula L. Gómez
1995 ◽  
Vol 1 (2-3) ◽  
pp. 75-90 ◽  
Author(s):  
J. Claude Cheftel

High pressure (1 to 10 kbars, i.e. 100-1000 MPa) affects biological constituents and systems. Several physicochemical properties of water are modified, such as the density, the ionic dissociation (and pH), and the melting point of ice. Pressure-induced unfolding, aggregation, and gelation of food proteins mainly depend on the effects of pressure on various noncovalent bonds and interactions. Enzyme inactivation (e.g., of ATPases) also results from similar effects, but some enzymes, including oxidative enzymes from fruits and vegetables, are strongly baroresistant. Chemical reactions, macromolecular transconformations, changes in membrane structure, or changes in crystal form and melting point that are accompanied by a decrease in volume are enhanced under pressure (and vice versa). Several of these phenomena, still poorly identified, are involved in the high inactivation ratio (5–6 logarithmic cycles) of most vegetative microbial cells: gram-negative bacteria, yeasts, complex viruses, molds, and gram-positive bacteria, in this decreasing order of sensitivity to pressure. Much variability is noted in the baroresistance of microorganisms, even within one single species or genus. Other parameters influence this resistance: pressure level, holding time (a two-phase kinetics of inactivation is often observed that prevents the calculation of decimal reduction times), temperature of pressure processing (temperatures above 50°C or between –30 and +5°C enhancing inactivation), composition of the medium or of the food (the pH having apparently little influence, but high salt or sugar concentrations, and low water contents, exerting very strong baroprotective effects). Taking into account the baroprotective effects of some food constituents and the strong resistance of some microbial strains, recent research aims at combined processes in which high pressure is associated with moderate temperature, CO2, other bacteriostatic agents, or to nonthermal physical processes such as ultrasounds, alternative currents, high-voltage electric pulses, and so forth. The safety and refrigerated shelf life of pressurized foods could be maintained or extended, while the sensorial quality should improve due to the reduced severity of thermal processing. Further research is, however, needed for the regulatory authorities to assess and accept these novel foods and processes.


2007 ◽  
Vol 53 (7) ◽  
pp. 813-821 ◽  
Author(s):  
N. Elmnasser ◽  
S. Guillou ◽  
F. Leroi ◽  
N. Orange ◽  
A. Bakhrouf ◽  
...  

In response to consumer preferences for high quality foods that are as close as possible to fresh products, athermal technologies are being developed to obtain products with high levels of organoleptic and nutritional quality but free of any health risks. Pulsed light is a novel technology that rapidly inactivates pathogenic and food spoilage microorganisms. It appears to constitute a good alternative or a complement to conventional thermal or chemical decontamination processes. This food preservation method involves the use of intense, short-duration pulses of broad-spectrum light. The germicidal effect appears to be due to both photochemical and photothermal effects. Several high intensity flashes of broad spectrum light pulsed per second can inactivate microbes rapidly and effectively. However, the efficacy of pulsed light may be limited by its low degree of penetration, as microorganisms are only inactivated on the surface of foods or in transparent media such as water. Examples of applications to foods are presented, including microbial inactivation and effects on food matrices.


Author(s):  
Oļegs Uzhga-Rebrov ◽  
Galina Kulešova

Nowadays, an ever-growing complexity of technical systems can be observed worldwide, problems of rational use of nature resources and diminution in negative impact on the environment are not completely settled yet, and international competition in different areas is strengthening. All the above tendencies cause an increase of different risks: technical, ecological, political, military and financial. Due to their nature, most of the risks are caused by a set of factors with commonly unknown relationships. Therefore, the need to use risk modelling methods that enable visual representation of the sets of cause-risk relationships becomes evident. This paper briefly examines two widely used techniques of modelling risky situations: fault trees and belief networks, and provides their comparative analysis.


2012 ◽  
Vol 7 (6) ◽  
Author(s):  
Frampton Franklin Santana ◽  
Pedro Esteves Duarte Augusto ◽  
Marcelo Cristianini

Thermal process is still the most used and safer method for food preservation. Although the mathematical modelling of heat transfer has been used for thermal process evaluation, microbial validation is rarely carried out, and the evaluation of retortable stand up pouch processes were not studied. The present work employed a finite elements analysis model (FEA) for the evaluation of a conductive meat pet food process sterilization in stand up retortable pouches. The results obtained by the model showed good agreement with the experimental values, for both temperature histories and microbial inactivation comparison. The results obtained demonstrate the utility of using mathematical models for describing the heat transfer and microbial inactivation in food thermal process, and reinforce that it can be a powerful tool in food process evaluation and design.


Nanomaterials ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 941 ◽  
Author(s):  
Sergio Torres-Giner ◽  
Cristina Prieto ◽  
Jose M. Lagaron

Food quality and safety are key aspects to guarantee that foods reach consumers in optimal conditions from the point of view of freshness and microbiology. Nanotechnology offers significant potential to secure or even enhance these aspects. Novel technologies, such as nanofabrication and nanoencapsulation, can provide new added value solutions for the fortification of foods with bioactives and targeted controlled release in the gut. Nanomaterials can also support food preservation aspects by being added directly into a food matrix or into food contact materials such as packaging. Thus, nanomaterials can be leveraged in the form of nanocomposites in food packaging design by melt compounding, solvent casting, lamination or electrohydrodynamic processing (EHDP) to promote passive, active, and even bioactive properties such as barrier, antimicrobial, antioxidant, and oxygen scavenging roles and the controlled release of functional ingredients. These attributes can be exerted either by the intended or non-intended migration of the nanomaterials or by the active substances they may carry. Lastly, nanomaterials can be advantageously applied to provide unique opportunities in Circular Bioeconomy strategies in relation to the valorization of, for instance, agro-industrial wastes and food processing by-products.


Sign in / Sign up

Export Citation Format

Share Document