Use of Borehole Shear Test to Obtain Shear Strength Data Comparison to Direct Shear Test

2018 ◽  
pp. 145-151
Author(s):  
R. M. Sbroglia ◽  
R. A. R. Higashi ◽  
M. S. Espíndola ◽  
V. S. Muller ◽  
P. Betiatto
Keyword(s):  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Direct Shear ◽  
Strength Data ◽  
Data Comparison

scholarly journals Influence of Structural Plane Microscopic Parameters on Direct Shear Strength

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Yanhui Cheng ◽  
Weijun Yang ◽  
Dongliang He
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Direct Shear ◽  
Stiffness Ratio ◽  
Structural Plane

Structural plane is a key factor in controlling the stability of rock mass engineering. To study the influence of structural plane microscopic parameters on direct shear strength, this paper established the direct shear mechanical model of the structural plane by using the discrete element code PFC2D. From the mesoscopic perspective, the research on the direct shear test for structural plane has been conducted. The bonding strength and friction coefficient of the structural plane are investigated, and the effect of mesoscopic parameters on the shear mechanical behavior of the structural plane has been analyzed. The results show that the internal friction angle φ of the structural plane decreases with the increase of particle contact stiffness ratio. However, the change range of cohesion is small. The internal friction angle decreases first and then increases with the increase of parallel bond stiffness ratio. The influence of particle contact modulus EC on cohesion c is relatively small. The internal friction angle obtained by the direct shear test is larger than that obtained by the triaxial compression test. Parallel bond elastic modulus has a stronger impact on friction angle φ than that on cohesion c. Under the same normal stress conditions, the shear strength of the specimens increases with particle size. The shear strength of the specimen gradually decreases with the increase of the particle size ratio.

Soil Shear Strength Characteristic in Slope Disintegration Area

2013 ◽  
Vol 353-356 ◽  
pp. 735-739
Author(s):  
Xiao Ming Zhang ◽  
Shu Wen Ding ◽  
Shuang Xi Li
Keyword(s):  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Clay Content ◽  
Scientific Basis ◽  
Soil Mechanic ◽  
Direct Shear ◽  
Soil Cohesion ◽  
Soil Shear Strength ◽  
The Relationship

Development of slope disintegration is close to soil mechanic characteristics such as shear strength indices. Soil grain diameter and water content were tested. Soil direct shear test was conducted to analyze the relationship between shear strength indices and the influencing factors. The experimental data indicate that clay content and the range affect soil cohesion value and the scope. Soil cohesion increases with bulk density before 1.6g/cm3. But it decreases when the bulk after that. The results could provide a scientific basis for control of slope disintegration.

scholarly journals Shear strength characteristics of Jerash expansive soil

2021 ◽  
Vol 3 (2) ◽  
pp. 74-80
Author(s):  
Talal Masoud
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Water Content ◽  
Direct Shear Test ◽  
Shear Test ◽  
Expansive Soil ◽  
Content Increase ◽  
Direct Shear ◽  
Initial Water ◽  
Angle Of Internal Friction

The results of the direct shear test on Jerash expansive soil show the effect of the initial water content on the cohesion (c) and on the angel of internal friction ( ) [shear strength parameters].it show that, as the initial water increase, the cohesion (c) of Jerash expansive soil also increase up to the shrinkage limit, after that increase of water even small amount, decrease the cohesion of the soil. On the other hand, the results of direct shear test show also  that as the water content increase, the angle of internal friction ( )remain unchanged up to shrinkage limit , any increase of water cause a large decrease on the angle of internal friction of Jerash expansive soil.

scholarly journals Study on Water Characteristic Curve and Shear Characteristics of Typical Unsaturated Silty Clay in Shaoxing

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Ruiqian Wu ◽  
Youzhi Tang ◽  
Shaohe Li ◽  
Wei Wang ◽  
Ping Jiang ◽  
...  
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Unsaturated Soil ◽  
Direct Shear Test ◽  
Shear Test ◽  
Characteristic Curve ◽  
Friction Angle ◽  
Matric Suction ◽  
Silty Clay ◽  
Direct Shear

In order to probe into one simplified method to predict the shear strength of Shaoxing unsaturated silty clay, the test method combining unsaturated soil consolidation instrument and conventional direct shear instrument is used to study the shear strength, and the method is compared and verified with the results of equal suction direct shear test. The research results show that the soil water characteristic curve fitted by the measured data points and VG model has obvious stage characteristics in the range of 0~38 kPa, 38~910 kPa, and 910~10000 kPa. The shear strength of unsaturated soil measured by consolidation meter combined with conventional direct shear test is in good agreement with that measured by equal suction direct shear test in the range of 0~500 kPa. The results show that the shear strength, total cohesion, and effective internal friction angle of soil increase slightly with the increase of matric suction in the range of 0~38 kPa. When the matric suction increases from 38 kPa to 500 kPa, the shear strength and total cohesion force of the soil have similar stage characteristics with the SWCC, which first increases and then tends to be stable, while the effective internal friction angle changes slightly. Finally, taking the air-entry value as the demarcation point, an improved model of unsaturated shear strength is proposed by analyzing the error value. Compared with the measured value, the absolute value of relative error is basically kept in the range of 5%~10%, which is close to the measured value.

scholarly journals Influence of Maximum Particle Diameter on the Mechanical Behavior of Soil-Rock Mixtures

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Zhuoling He ◽  
Junyun Zhang ◽  
Tao Sun
Keyword(s):  
Shear Strength ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Particle Diameter ◽  
Size Difference ◽  
Direct Shear ◽  
Fine Grained ◽  
Fine Grained Soil ◽  
Maximum Particle

With the steady development of the development of the western region in China, the construction of mountain highways has developed rapidly, and the soil-rock mixed filler, as an excellent filler, is widely used in the subgrade filling of mountain highways. Unlike ordinary fine-grained soil, the source of the soil-rock mixtures (S-RMs) is not unique, and the particle size difference is large and the water content is not uniform, resulting in very complicated mechanical properties. But the current highway embankment codes are still mainly established on the fine-grained soil. It is not fully applicable to soil-rock filled embankment. Based on soil-rock filled embankment engineering practice, this research uses a large-scale direct shear test to research the mechanical characteristics of the S-RMs with different maximum particle diameters. According to the large-scale direct shear test of S-RMs with different maximum particle diameters, the shear displacement vs shear stress curve, shear dilation, and strength characteristics with maximum particle diameter were analyzed. Results demonstrate that whether secondary hardening occurs mainly depends on the normal stress and the maximum particle diameter of the filler. At different maximum particle diameters, the horizontal displacement vs vertical displacement curves of the S-RMs can be roughly divided into continuous shearing and beginning of shearing and quick dilation. And the shear strength increases with the increase of the maximum particle diameter. Moreover, the cohesion decreases first and then increases with the increase of the maximum particle diameter, and the internal friction angle increases with the increase of the maximum particle diameter. Therefore, some RBs with large particle diameter added to filler can effectively improve the shear strength of the S-RMs, which may be valuable for realistic engineering.

scholarly journals Determining the Shear Strength Properties of a Soil-geogrid Interface Using a Large-scale Direct Shear Test Apparatus

2020 ◽  
Author(s):  
Jakub Stacho ◽  
Monika Sulovska ◽  
Ivan Slavik
Keyword(s):  
Shear Stress ◽  
Shear Strength ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Strength Properties ◽  
Coarse Grained ◽  
Direct Shear ◽  
Test Apparatus ◽  
Fine Gravel

The paper deals with the laboratory testing of coarse-grained soils that are reinforced using a geogrid. The shear strength properties were determined using a large-scale direct shear test apparatus. The tests were executed on original as well as on reinforced soil, when the geogrid was placed on a sliding surface, which permitted determining the shear strength properties of the soil-geogrid interface. The aim of the tests was to determine the interface shear strength coefficient α, which represents the ratio of the shear strength of the soil-geogrid interface to the unreinforced soil. The tests were executed on 3 samples of coarse-grained materials, i.e., poorly graded sand, poorly graded fine gravel and poorly graded medium gravel. Two types of geogrids were tested, i.e., a woven polyester geogrid and a stiff polypropylene geogrid. The results of the laboratory tests on the medium gravel showed that the reduction coefficient α reached higher values in the case of the stiff polypropylene geogrid. In the cases of the fine gravel and sand, the values of the interface coefficient α were similar to each other. The shear strength of the interface was reduced or was similar to the shear strength of unreinforced soil in a peak shear stress state, but significantly increased with horizontal deformations, especially for the fine gravel and sand. The largest value of the coefficient α was measured in the critical shear stress state. Based on the results of the testing, a correlation which allows for determining the optimal grain size distribution was obtained.

The Research on the Mechanical Properties of the same Curing Agent of Different Soil Dredged Mud

2013 ◽  
Vol 800 ◽  
pp. 181-188
Author(s):  
Xiao Yan Yang ◽  
Wen Bai Liu ◽  
Jia Jun Wang ◽  
Wen Hui Shi
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Compression Test ◽  
Direct Shear Test ◽  
Shear Test ◽  
Silty Sand ◽  
Curing Agent ◽  
Direct Shear ◽  
Confined Compression ◽  
Silty Soil

Through confined compression test and direct shear test, studied the mechanical properties of the same curing agent of different soil dredged mud, compared the difference of the same curing agent of different soil dredged mud. By confined compression test, the compression modulus of clay, silty sand and silty soil dredged mud after curing increases by 603.7%, 529.0% , 603.7% respectively. By direct shear test, the shear strength of clay dredged mud after curing increases to infinity; silty sands shear strength after curing increases by 209.1% in average; silty soils shear strength increases after curing by 147.5% in average. The compression and shear resistance of this kind of special curing agent for clay is best, silty sand second, but for the silty soil only has a little effect.

Shear strength of sandstone–mudstone particle mixture from direct shear test

2018 ◽  
Vol 77 (12) ◽  
Author(s):  
Jun-jie Wang ◽  
Jian-jun Guo ◽  
Ji-ping Bai ◽  
Xiao Wu
Keyword(s):  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Direct Shear ◽  
Particle Mixture

scholarly journals Effect of Rock Particle Content on the Mechanical Behavior of a Soil-Rock Mixture (SRM) via Large-Scale Direct Shear Test

2019 ◽  
Vol 2019 ◽  
pp. 1-16
Author(s):  
Longqi Liu ◽  
Xuesong Mao ◽  
Yajun Xiao ◽  
Qian Wu ◽  
Ke Tang ◽  
...  
Keyword(s):  
Shear Strength ◽  
Normal Stress ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Volumetric Strain ◽  
Direct Shear ◽  
Stress Strain ◽  
Particle Content ◽  
Rock Particle

The mechanical strength of the landslide deposits directly affects the safety and operation of the roads in the western mountainous area of China. Therefore, the research is aimed at studying the mechanisms of a landslide deposit sample with different rock particle contents by analyzing its characteristics of the stress-strain behavior, the “jumping” phenomenon, the volumetric strain, and the shear strength parameters via a large-scale direct shear test. Stress-strain results show that stress-strain curves can be divided into 3 different stages: liner elastic stage, yielding stage, and strain-hardening stage. The shear strength of SRM behaves more like “soil” at a lower rock particle content and behaves more like “rock joints” at a higher rock particle content. Characteristics of the “jumping” phenomenon results show that the “intense jumping” stage becomes obvious with the increasing rock particle content and the normal stress. However, the lower the rock particle content is, the more obvious the “jumping” phenomenon under the same normal stress is. Volumetric strain results show that the sample with a lower rock particle content showed a dilatancy behavior under the low normal stress and shrinkage behavior under the high normal stress. The dilatancy value becomes smaller with the increasing normal stress. The maximum shear stress value of the rock particle content corresponds to the maximum value of dilatancy or shrinkage. We also conclude that the intercept of the Mohr failure envelope of the soil-rock mixture should be called the “equivalent cohesion,” not simply called the “cohesion.” The higher the normal stress and rock particle content are, the bigger the equivalent cohesion and the internal friction angle is.

The Research of Shear Strength and Micro-Structural Characteristics of Acid Pollution Laterite

2013 ◽  
Vol 405-408 ◽  
pp. 566-570
Author(s):  
Ying Huang ◽  
Tong Zhen Bo ◽  
Ke Sheng Jin ◽  
Zu Lian Zhang
Keyword(s):  
Shear Strength ◽  
Hydrochloric Acid ◽  
Acid Concentration ◽  
Direct Shear Test ◽  
Shear Test ◽  
Structural Characteristics ◽  
Direct Shear ◽  
Microstructure Characteristics ◽  
Acid Pollution ◽  
Source Of Pollution

With hydrochloric acid as the source of pollution, with laterite as the pollution soil, the shear strength and micro-structural characteristics of acid pollution laterite are studied by direct shear test. The results shown that, the shear strength and microstructure characteristics of acid pollution laterite are affected acid concentration and pollution time. The shear strength and indexes of acid pollution laterite decrease in general with the increase of acid concentration and the extension of the specimen pollution time, the shear strength and indexes exist a minimal value at lower concentration and shorter pollution time, the shear strength and indexes exist a great value at higher concentration and longer pollution time, the corresponding microstructure images present to the characteristics of compactness, roughness, color, texture.

Sign in / Sign up

Export Citation Format

Share Document