Experimental Study on Effect of Water Flow Rate on Heating Performance of a Series Bathing Wastewater Source Heat Pump Hot Water Unit

2020 ◽  
pp. 781-789
Author(s):  
Liangdong Ma ◽  
Tixiu Ren ◽  
Tianyi Zhao ◽  
Jili Zhang
Keyword(s):  
Experimental Study ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Heating Performance ◽  
Effect Of Water

scholarly journals Mapping Relevant Parameters for Efficient Operation of Low-Temperature Heating Systems in Nordic Single-Family Dwellings

2018 ◽  
Vol 8 (10) ◽  
pp. 1973 ◽  
Author(s):  
Adnan Ploskić ◽  
Qian Wang ◽  
Sasan Sadrizadeh
Keyword(s):  
Low Temperature ◽  
Environmental Impact ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Single Family ◽  
Efficient Operation ◽  
Heating Systems

The aim of this study was to map the parameters that have the greatest impact on the environmental impact of heating systems usually used in Nordic single-family dwellings. The study focused on mapping the technical requirements for efficient operation of heating systems in a broader context. The results suggest that the ability of a heating system to be operated with a low-temperature water supply depends to a large extent on the heating demand of a building. It was shown that an increase in the water flow rate in hydronic circuits would significantly increase the thermal efficiency from analyzed heating systems. This increase would not increase the pumping power need, nor would it create noise problems in distribution network if the distribution pipes and thermostatic valves were properly selected. However, this increase in water flow rate improved the efficiency of considered closed-loop heat pump. It was further shown that the efficiency of the heat pump could be additionally improved by halving the energy needs for the domestic hot-water and circulators. The main conclusion from this study is that exergy usage, CO2 emission and thereby environmental impact are significantly lower for heating systems that are operated with small temperature drops.

scholarly journals An experimental investigation on the coefficient of performance of the small hot water heat pump using refrigeration R410A and R32

2020 ◽  
Vol 3 (2) ◽  
pp. First
Author(s):  
Le Minh Nhut ◽  
Tran Quang Danh
Keyword(s):  
Ambient Temperature ◽  
Water Temperature ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Electric Heater ◽  
Initial Water

Hot water is an important factor in domestic life and industrial development. Today, the heat pump is used to produce hot water more and more popular because it has many advantages of saving energy compared to the method of producing hot water by the hot water electric heater. The main aim of this study is to evaluate of the coefficient of performance (COP) of the small hot water heat pump using refrigeration R410A and R32. The capacity of both hot water heat pump is similar, one using new refrigerant R32 and other using refrigerant R410A. These heat pumps were designed and installed at the Ho Chi Minh City University of Technology and Education to evaluate the COP for the purpose of application the new refrigerant R32 for hot water heat pump. The compressor capacity is 1 Hp, the volume of hot water storage tank is of 100 liters and is insulated with thickness of 30 mm to reduce the heat loss to invironment, the required hot water temperature at the outlet of condenser is 50 oC, and the amount of required hot water is 75 liters per batch and is controlled by float valve. The experimental results indicate that the COP of the heat pump using the new refrigerant R32 is higher than heat pump using refrigerant R410A from 9% to 15% when the experimental conditions such as ambient temperature, initial water flow rate through the condenser and the required temperature of hot water were the same. In addition, the effect of the ambient temperature, initial water temperature and water flow rate were also evaluated.

scholarly journals Effect of Water Flow on Underwater Wet Welded A36 Steel

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 682
Author(s):  
Eko Surojo ◽  
Aziz Harya Gumilang ◽  
Triyono Triyono ◽  
Aditya Rio Prabowo ◽  
Eko Prasetya Budiana ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Flow ◽  
Flow Rate ◽  
Water Flow Rate ◽  
Physical And Mechanical Properties ◽  
Shielded Metal Arc Welding ◽  
Effect Of Water ◽  
Bending Effect ◽  
Metal Arc Welding ◽  
A36 Steel

Underwater wet welding (UWW) combined with the shielded metal arc welding (SMAW) method has proven to be an effective way of permanently joining metals that can be performed in water. This research was conducted to determine the effect of water flow rate on the physical and mechanical properties (tensile, hardness, toughness, and bending effect) of underwater welded bead on A36 steel plate. The control variables used were a welding speed of 4 mm/s, a current of 120 A, electrode E7018 with a diameter of 4 mm, and freshwater. The results show that variations in water flow affected defects, microstructure, and mechanical properties of underwater welds. These defects include spatter, porosity, and undercut, which occur in all underwater welding results. The presence of flow and an increased flow rate causes differences in the microstructure, increased porosity on the weld metal, and undercut on the UWW specimen. An increase in water flow rate causes the acicular ferrite microstructure to appear greater, and the heat-affected zone (HAZ) will form finer grains. The best mechanical properties are achieved by welding with the highest flow rate, with a tensile strength of 534.1 MPa, 3.6% elongation, a Vickers microhardness in the HAZ area of 424 HV, and an impact strength of 1.47 J/mm2.

scholarly journals Effects of water flow rate and surface cover plant density on the growth of duckweed (Lemna minor L.)

2020 ◽  
Vol 5 (2) ◽  
pp. 98
Author(s):  
Renata Caprina Samantha Mahadewi Hutabarat ◽  
Didik Indradewa
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Plant Density ◽  
Lemna Minor ◽  
Water Flow Rate ◽  
Organic Fertilizers ◽  
Growth And Yield ◽  
Surface Cover ◽  
Agriculture Sector ◽  
Effect Of Water

Globally, agriculture sector is facing unprecedented challenges in producing fertilizers and increasing the amount of fertilizer production without having negative impact on the environment. Thus, the organic fertilizers are needed to be produced as they do not give any damages to the environment. Duckweed plant has a lot of potentials that can be used in the agriculture sector. This plant can breed in approximately 16-48 hours by splitting. The water needs and its breeding speed ability are the basis for conducting this research. The research objective was to determine the effect of water flow rate and surface cover plant density on the growth and yield of duckweed plants. This research was conducted in November–December 2018 in Cangkringan District, Sleman, Special Region of Yogyakarta, Indonesia. The experiment was arranged in a split plot design. The main plot was irrigation water flow rate, consisting of two levels, namely large water flow rate (0.336 L.second-1) and small water flow rate (0.085 L.second-1). The subplot was the density of the duckweed plant surface cover, consisting of 10%, 20%, 40% and 60%. The results of this study indicated there was no effect of water flow rate on the plant growth, yield, and yield quality of duckweed plants. The C/N ratio of the duckweed plants fulfilled the requirement to be used as green manure.

scholarly journals Experimental Study of the Gas Engine Driven Heat Pump with Engine Heat Recovery

2015 ◽  
Vol 2015 ◽  
pp. 1-10 ◽  
Author(s):  
Wei Zhang ◽  
Tao Wang ◽  
Sulu Zheng ◽  
Xueyuan Peng ◽  
Xiaolin Wang
Keyword(s):  
Ambient Temperature ◽  
Water Flow ◽  
Heat Pump ◽  
Flow Rate ◽  
Heat Recovery ◽  
Engine Speed ◽  
Water Flow Rate ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Gas Engine

Gas engine driven heat pumps (GEHPs) represent one of practical solutions to effectively utilize fossil fuel energy and reduce environmental pollution. In this paper, the performance characteristics of the GEHP were investigated experimentally with engine heat recovery. A GEHP test facility was set up for this purpose. The effects of several important factors including engine speed, ambient temperature, condenser water flow rate, and condenser water inlet temperature on the system performance were studied over a wide range of operating conditions. The results showed that the engine waste heat accounted for about 40–50% of the total heat capacity over the studied operating conditions. It also showed that engine speed and ambient temperature had significant effects on the GEHP performance. The coefficient of performance (COP) and the primary energy ratio (PER) decreased by 14% and 12%, respectively, as engine speed increased from 1400 rpm to 2000 rpm. On the other hand, the COP and PER of the system increased by 22% and 16%, respectively, with the ambient temperature increasing from 3 to 12°C. Furthermore, it was demonstrated that the condenser water flow rate and condenser water inlet temperature had little influence on the COP of the heat pump and the PER of the GEHP system.

Sign in / Sign up

Export Citation Format

Share Document