The effects of cutting parameters and tool geometry on cutting forces and tool wear in milling high-density fiberboard with ceramic cutting tools

2017 ◽  
Vol 91 (9-12) ◽  
pp. 4033-4041 ◽  
Author(s):  
Zhaolong Zhu ◽  
Xiaolei Guo ◽  
Mats Ekevad ◽  
Pingxiang Cao ◽  
Bin Na ◽  
...  
Keyword(s):  
Tool Wear ◽  
Cutting Forces ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
High Density ◽  
Tool Geometry

CBN Tool Wear Modeling in Finish Hard Turning

Manufacturing ◽  
2003 ◽  
Author(s):  
Yong Huang ◽  
Steven Y. Liang
Keyword(s):  
Tool Wear ◽  
Hard Turning ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Wear Volume ◽  
Wear Rates ◽  
Cbn Tool ◽  
Finish Hard Turning

The cubic boron nitride (CBN) cutting tools are commonly used for single point turning of hardened materials. The wear behavior and tool life of CBN cutters are important issues in order for hard turning to be a viable technology in view of the high cost of CBN cutting tools and the cost of down-time for tool change. The objective of this study is to develop a methodology to model the rate of CBN tool wear on both the flank and rake faces. The model can serve both as a basis to guide the design of CBN tool geometry and to optimize cutting parameters in finish hard turning. First, the kinematics, stress distribution, and temperature variation on the tool flank and rake faces are formulated. Subsequently, the wear volume loss is modeled as functions of cutting temperature, stress, and other process information based on the consideration of main wear mechanisms of abrasion, adhesion, and diffusion. Then, flank/crater wear rates are predicted in terms of tool/work material properties and cutting configuration. Finally, based on the calibrated wear coefficients in independent tests, the proposed models are experimentally validated in finish turning hardened 52100 bearing steel using a low CBN content insert. The model predictions agree with the measurements in terms of the behavior of stable growths of wear land and crater. The adhesion is found to be the dominating wear mechanism over the range of cutting parameters examined.

scholarly journals Effect of Cutting Parameters and Tool Geometry on the Performance Analysis of One-Shot Drilling Process of AA2024-T3

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 854
Author(s):  
Muhammad Aamir ◽  
Khaled Giasin ◽  
Majid Tolouei-Rad ◽  
Israr Ud Din ◽  
Muhammad Imran Hanif ◽  
...  
Keyword(s):  
Feed Rate ◽  
Surface Defects ◽  
Thrust Force ◽  
Cutting Tools ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Machining Process ◽  
Tool Geometry ◽  
Drilling Process

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

scholarly journals An experimental research on the machinability of a high temperature titanium alloy BTi-6431S in turning process

2018 ◽  
Vol 5 ◽  
pp. 12
Author(s):  
Yanfeng Gao ◽  
Yongbo Wu ◽  
Jianhua Xiao ◽  
Dong Lu
Keyword(s):  
Titanium Alloy ◽  
High Temperature ◽  
Tool Wear ◽  
Titanium Alloys ◽  
Cutting Forces ◽  
Shear Bands ◽  
Cutting Parameters ◽  
Aircraft Manufacturing ◽  
Mechanical And Physical Properties ◽  
Alpha Titanium

Titanium alloys are extensively applied in the aircraft manufacturing due to their excellent mechanical and physical properties. At present, the α + β alloy Ti6Al4V is the most commonly used titanium alloy in the industry. However, the highest temperature that it can be used only up to 300 °C. BTi-6431S is one of the latest developed high temperature titanium alloys, which belongs to the near-α alloy group and has considerably high tensile strength at 650 °C. This paper investigates the machinability of BTi-6431S in the terms of cutting forces, chip formation and tool wear. The experiments are carried out in a range of cutting parameters and the results had been investigated and analyzed. The investigation shows that: (1) the specific cutting forces in the machining of BTi-6431S alloy are higher than in the machining of Ti6Al4V alloy; (2) the regular saw-tooth chips more easily formed and the shear bands are narrower in the machining of BTi-6431S; (3) SEM and EDS observations of the worn tools indicate that more cobalt elements diffuse into the workpiece from tool inserts during machining of BTi-6431S alloy, which significantly aggravates tool wear rate. The experimental results indicate that the machinability of BTi-6431S near alpha titanium alloy is significantly lower than Ti-6Al-4V alloy.

scholarly journals Enhancing Wear Resistance and Cutting Performance of a Long-Life Micro-Groove Tool in Turning AISI 201

Coatings ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1515
Author(s):  
Jinxing Wu ◽  
Lin He ◽  
Yanying Wu ◽  
Chaobiao Zhou ◽  
Zhongfei Zou ◽  
...  
Keyword(s):  
Temperature Field ◽  
Service Life ◽  
Tool Wear ◽  
Cutting Forces ◽  
Cutting Tools ◽  
Cutting Temperature ◽  
Rake Angle ◽  
Rake Face ◽  
Crater Wear ◽  
Wear Area

Tool-chip friction increases cutting temperature, aggravates tool wear, and shortens the service life of cutting tools. A micro-groove design of the rake face can improve the wear performance of the tool. In this study, we used the finite element simulation “Deform” to obtain the temperature field distribution of the tool rake face. The size of the micro-groove was determined by selecting a suitable temperature field combined with the characteristics of tool–chip flow in the cutting process, and the tool was prepared using powder metallurgy. The three-direction cutting forces and tool tip temperature were obtained by a cutting test. Compared with the original turning tool, the cutting force and cutting temperature of the micro-groove tool were reduced by more than 20%, the friction coefficient was reduced by more than 14%, the sliding energy was reduced and the shear energy was greatly decreased. According to the analysis of tool wear by SEM (scanning electron microscope) and EDS (energy dispersive X-ray spectroscopy), the crater wear, adhesive wear and oxidation wear of the micro-groove tool were lower than those of the original turning tool. In particular, the change in the crater wear area on the rake face of the original tool and the micro-groove tool was consistent with the cutting temperature and the wear width of the flank face. On the whole, the crater wear area and the change rate of the crater wear area of the micro-groove tool were smaller. Due to the proper microgroove structure of the rake face, the tool-chip contact area decreased, and the second rake angle of the tool became larger. Hence, the tool-chip friction, cutting forces, cutting energy consumption were reduced, tool wear was improved, and the service life of the micro-groove tool was five times longer than that of the original tool.

scholarly journals Online Tool Wear Monitoring by the Analysis of Cutting Forces in Transient State for Dry Machining of Ti6Al4V Alloy

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 1014 ◽  
Author(s):  
Sánchez Hernández ◽  
Trujillo Vilches ◽  
Bermudo Gamboa ◽  
Sevilla Hurtado
Keyword(s):  
Tool Wear ◽  
Feed Rate ◽  
Cutting Forces ◽  
Flank Wear ◽  
Cutting Speed ◽  
Transient State ◽  
Cutting Parameters ◽  
Dry Machining ◽  
Crater Wear ◽  
Force Amplitude

In this work, the analysis of the cutting speed and feed rate influence on tool wear and cutting forces in Ti6Al4V alloy dry machining is presented. The study has been focused on the machining in a transient state. The tool wear mechanisms, tool wear intensity and cutting forces evolution have been analyzed as a function of the cutting parameters. Experimental results show that the main cutting force amplitude exhibits a general trend to increase with both cutting parameters. Crater wear was more evident at high cutting speeds, whereas flank wear was present on the whole interval of the cutting parameters analyzed. Furthermore, the cutting speed shows a slightly higher influence on crater wear and the feed rate shows a higher influence on flank wear. Finally, several experimental parametric models have been obtained. These models allow predicting the evolution of crater and flank tool wear, as well as the cutting forces, as a function of the cutting parameters. Additionally, a model that allows monitoring the tool wear on the machining transient state as a function of the main cutting force amplitude has been developed.

Reinforcement and Cutting Tools Interaction during MMC Machining - A Review

2018 ◽  
Vol 22 ◽  
pp. 47-54 ◽  
Author(s):  
Mukesh Chaudhari ◽  
M. Senthil Kumar
Keyword(s):  
Tool Wear ◽  
Metal Matrix Composites ◽  
Process Parameters ◽  
Surface Finish ◽  
Metal Matrix ◽  
Cutting Tools ◽  
Tool Geometry ◽  
Matrix Composites ◽  
Good Surface ◽  
Aerospace Medical

Aluminum based metal matrix composites (AMMC) have found its applications in the automobile, aerospace, medical, and metal industries due to their superior mechanical properties. Fabricated Aluminum based metal matrix composites require machining to improve the surface finish and dimensional tolerance. Machining should be accomplished by good surface finish by consuming lowest energy and less tool wear. This paper reviews the machining of Aluminum based metal matrix composites to investigate the effect of process parameters such as tool geometry, tool wear, surface roughness, chip formation and also process parameters.

Study on Tool Life and Tool Wear Mechanisms in Dry Cutting Pure Iron

2013 ◽  
Vol 770 ◽  
pp. 74-77 ◽  
Author(s):  
Jin Xing Kong ◽  
Liang Li ◽  
Dong Ming Xu ◽  
Ning He
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanisms ◽  
Pure Iron ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Cutting Condition ◽  
High Plasticity ◽  
Dry Cutting ◽  
Tool Wear Mechanisms

Pure iron is a kind of high plasticity and toughness material. In the process of cutting pure iron, the tool wear is very serious. In this paper, three kinds of cutting tools KC5010, K313 and 1105 are used in the cutting pure iron process and the tool wear tests in dry cutting condition with different cutting parameters have been carried out. According to the results, the tool wear mechanisms and tool life of three kinds of cutting tools have been compared and analyzed. It is concluded that the tool life of K313 is better than KC5010 and 1105 and the three kinds of tool mechanisms are primarily adhesion wear, diffusion wear and oxidation wear.

Experimental Investigation on the Effect of Tool Geometry and Cutting Conditions Using Tool Wear Prediction Model for End Milling Process

2014 ◽  
Vol 13 (01) ◽  
pp. 41-54 ◽  
Author(s):  
S. Kalidass ◽  
P. Palanisamy
Keyword(s):  
Tool Wear ◽  
End Milling ◽  
Cutting Parameters ◽  
304 Stainless Steel ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Work Piece ◽  
Cutting Condition ◽  
Machining Parameter

Tool wear of a cutting tool has a significant impact on the tool life and surface quality of the finished product. Tool wear is influenced by many factors such as cutting parameters, tool geometry, coating type, work piece material, chatter, and cutting condition. In the present work, the design of experiments (DOE) technique has been used for four factors at five levels to conduct experiments. Tool wear is taken as the response variable measured during end milling, while helix angle, spindle speed, feed and depth of cut are taken as the input parameters. The material and tool selected for this study are AISI 304 stainless steel and uncoated solid carbide end mill cutter respectively. The tool wear was measured using tool maker's microscope. The experimental values are used in six sigma software for finding the coefficients to develop the regression model. The direct and interaction effect of the machining parameter with tool wear were analyzed using contour graphs, which helped to select process parameters for reducing tool wear and also ensure quality of milling.

Tool Wear Characters in Micro-Milling of Fully Sintered ZrO2 Ceramics by Diamond Coated End Mills

2012 ◽  
Vol 723 ◽  
pp. 365-370 ◽  
Author(s):  
Rong Bian ◽  
Eleonora Ferraris ◽  
Jun Qian ◽  
Dominiek Reynaerts ◽  
Liang Li ◽  
...  
Keyword(s):  
Tool Wear ◽  
Cutting Tools ◽  
Chemical Vapour ◽  
Cutting Parameters ◽  
Micro Milling ◽  
Machined Surface ◽  
Coated Tools ◽  
Machined Surface Quality ◽  
Coating Delamination ◽  
End Mills

This work presents an experimental investigation on micro-milling of fully sintered Zirconia (ZrO2) by diamond coated tools. The experiments were conducted on a Kern MMP 2522 micro-milling centre and WC micro end mills, diamond coated by chemical vapour deposition (CVD) and of stiff geometry were employed as cutting tools. The effects of cutting parameters and milling time on tool wear were investigated. The results revealed that the tool wear characters included diamond coating delamination and wear of substrate WC. Both cutting forces and machined surface quality were affected by tool wear with the progress of milling.

Sign in / Sign up

Export Citation Format

Share Document