Combined effects of UV light and elevated temperatures on wood discolouration

2015 ◽  
Vol 49 (6) ◽  
pp. 1225-1237 ◽  
Author(s):  
Laszlo Tolvaj ◽  
Satoru Tsuchikawa ◽  
Tetsuya Inagaki ◽  
Denes Varga
2017 ◽  
Vol 14 (17) ◽  
pp. 3971-3977 ◽  
Author(s):  
Blair Thomson ◽  
Christopher David Hepburn ◽  
Miles Lamare ◽  
Federico Baltar

Abstract. Microbial extracellular enzymatic activity (EEA) is the rate-limiting step in the degradation of organic matter in the oceans. These extracellular enzymes exist in two forms: cell-bound, which are attached to the microbial cell wall, and cell-free, which are completely free of the cell. Contrary to previous understanding, cell-free extracellular enzymes make up a substantial proportion of the total marine EEA. Little is known about these abundant cell-free enzymes, including what factors control their activity once they are away from their sites (cells). Experiments were run to assess how cell-free enzymes (excluding microbes) respond to ultraviolet radiation (UVR) and temperature manipulations, previously suggested as potential control factors for these enzymes. The experiments were done with New Zealand coastal waters and the enzymes studied were alkaline phosphatase (APase), β-glucosidase, (BGase), and leucine aminopeptidase (LAPase). Environmentally relevant UVR (i.e. in situ UVR levels measured at our site) reduced cell-free enzyme activities by up to 87 % when compared to controls, likely a consequence of photodegradation. This effect of UVR on cell-free enzymes differed depending on the UVR fraction. Ambient levels of UV radiation were shown to reduce the activity of cell-free enzymes for the first time. Elevated temperatures (15 °C) increased the activity of cell-free enzymes by up to 53 % when compared to controls (10 °C), likely by enhancing the catalytic activity of the enzymes. Our results suggest the importance of both UVR and temperature as control mechanisms for cell-free enzymes. Given the projected warming ocean environment and the variable UVR light regime, it is possible that there could be major changes in the cell-free EEA and in the enzymes contribution to organic matter remineralization in the future.


PLoS ONE ◽  
2018 ◽  
Vol 13 (1) ◽  
pp. e0191947 ◽  
Author(s):  
Michael Sswat ◽  
Martina H. Stiasny ◽  
Fredrik Jutfelt ◽  
Ulf Riebesell ◽  
Catriona Clemmesen

MRS Bulletin ◽  
2010 ◽  
Vol 35 (1) ◽  
pp. 35-40 ◽  
Author(s):  
Masahito Tagawa ◽  
Timothy K. Minton

AbstractThis article focuses on mechanistic aspects of hyperthermal atomic oxygen reactions with polymers, which are the major contributor to material degradation in low Earth orbit. Due to the importance of well-controlled experiments in the understanding of the reaction mechanisms, ground-based experimental results obtained by a hyperthermal atomic oxygen beam generated by laser detonation facilities are mainly surveyed. Combined effects of atomic oxygen and vacuum ultraviolet (VUV) light on fluorinated polymers are also described. Such combined effects of hyperthermal atomic oxygen and VUV light are important not only from a fundamental point of view but also for engineering purposes (i.e., methodology for ground-based space environmental simulation). The VUV-sensitive polymers, poly(methyl methacrylate), and Teflon fluorinated ethylene-propylene do not show significant synergistic effects. Instead, the effect of combining atomic oxygen and VUV light produces erosion of the polymer that is the sum of the erosion caused by atomic oxygen and UV light acting individually. The experimental results suggest that material erosion in a complicated space environment may be quantitatively predicted if the erosion yields caused by the individual action of atomic oxygen and VUV light are known.


Author(s):  
David Berry ◽  
Mehar Chand Meelu ◽  
Bruce G. McMordie ◽  
Thomas A. Kircher

A variety of coatings have been designed to protect turbine components from corrosion due to the combined effects of environmental contaminants, fuel impurities and elevated temperatures. The most effective of these systems rely upon formation of a protective alumina scale to act as a barrier between the gas path environment and the component. Protection offered by these alumina-forming high temperature coatings is increased by a number of additive elements, including platinum and chromium, but silicon (Si) is found to be especially beneficial in coatings exposed to high concentrations of sulfur in marine environments. Silicon-modified slurry aluminides are shown to resist to both high temperature and low temperature hot corrosion on both nickel and cobalt alloys in marine service. Laboratory tests show this corrosion resistance can be further enhanced by redistributing critical elements (particularly silicon) within the microstructure of the silicon-modified aluminide. The benefits of these changes are demonstrated in field engine trials.


Author(s):  
Michael DiGrazia ◽  
Randy Gee ◽  
Gary Jorgensen

Reflectors are an essential part of parabolic trough solar electric and other concentrating solar power (CSP) systems. Reflectors in CSP systems require a high reflectance over the solar wavelength spectrum and they must be durable to outdoor exposure and resist all forms of degradation over time. All utility-scale CSP systems installed to date use glass reflectors. Glass mirrors have maintained their reflectance very well in CSP environments, but they are susceptible to wind-related breakage and are expensive to transport and install. Alternative lower-cost reflectors are needed to reduce the cost of CSP systems [1]. ReflecTech® Mirror Film is a highly reflective polymer-based film co-developed with the National Renewable Energy Laboratory (NREL) for concentrating solar energy applications. The attributes of ReflecTech® Mirror Film and test results for weatherability are described herein. This paper discusses field and lab test results and properties of ReflecTech® Mirror Film, specifically: 1. Stability under ultraviolet (UV) light through accelerated testing and outdoor real-time testing. 2. Mechanical stability and resistance to moisture through water immersion tests for delamination and “tunneling”. 3. Mechanical resistance to high wind events common in utility-scale concentrating solar power applications. 4. Lighter weight and resistance to breakage that reduces transportation and installation costs, and allows greater design flexibility of concentrator geometries. 5. Lower initial cost compared with curved glass mirrors. To test for weatherability, reflector samples were subjected to controlled conditions more extreme than actual outdoor environments. NREL maintains a world-class testing capability for solar reflectors that includes a Solar Simulator (SS), QUV (an accelerated exposure chamber manufactured by Q-Lab Corp. that subjects materials to alternating cycles of light and condensation at elevated temperatures), and several WeatherOmeter® (WOM) exposure chambers that allow accelerated testing of reflector samples. In addition, samples of ReflecTech® Mirror Film have been subjected to ACUVEX® accelerated outdoor weathering tests (natural sunlight in Phoenix, AZ, concentrated 7 to 8 times with a Fresnel-reflector while the samples are cooled with a fan to near ambient conditions and sprayed with de-ionized water 8 min per natural sun hour). Immersion tests were also performed to test the resistance of ReflecTech® Mirror Film to extreme moisture. Test results compared ReflecTech® film performance to past film products like 3M’s ECP-300 and ECP-305+ which suffered from “tunneling” [2], a problem whereby the silver reflective layer delaminates from the polymer film in the presence of moisture.


Ecotoxicology ◽  
2007 ◽  
Vol 16 (4) ◽  
pp. 371-377 ◽  
Author(s):  
Dorthe Groth Petersen ◽  
Ingela Dahllöf

2018 ◽  
Vol 50 (1) ◽  
pp. 39-50 ◽  
Author(s):  
Jelena Vujancevic ◽  
Andjelika Bjelajac ◽  
Jovana Cirkovic ◽  
Vera Pavlovic ◽  
Endre Horvath ◽  
...  

One-dimensional (1D) TiO2 nanotubes perpendicular to the substrate were obtained by electrochemical oxidation of titanium foil in an acid electrolyte. In order to alter the crystallinity and the morphology of films the as-anodized amorphous TiO2 nanotube films were sintered at elevated temperatures. The evolution of the morphology was visualized via scanning electron microscopy (SEM), while the crystalline structure was investigated by X-ray diffraction (XRD) and Raman spectroscopy. The chemical composition was studied by X-ray photoelectron spectroscopy (XPS). The effects of crystallinity and morphology of TiO2 nanotube (NTs) films on photocatalytic degradation of methyl orange (MO) in an aqueous solution under UV light irradiation were also investigated. The TiO2 nanotubes sintered at 650?C for 30 min had the highest degree of crystallinity and exhibited the best photocatalytic activity among the studied TiO2 nanotube films.


Sign in / Sign up

Export Citation Format

Share Document