scholarly journals On the electrical characteristics of Al/p-Si diodes with and without (PVP: Sn-TeO2) interlayer using current–voltage (I–V) measurements

2020 ◽  
Vol 126 (12) ◽  
Author(s):  
Abbas Sabahi Namini ◽  
Mehdi Shahedi Asl ◽  
Gholamreza Pirgholi-Givi ◽  
Seyed Ali Delbari ◽  
Javid Farazin ◽  
...  
Keyword(s):  
Series Resistance ◽  
Thermionic Emission ◽  
Reverse Current ◽  
Current Transport ◽  
Electrical Characteristics ◽  
Transport Mechanisms ◽  
Electrical Parameters ◽  
Zero Bias ◽  
Current Voltage ◽  
Significant Increment

AbstractThe present study aims to investigate the effect of (PVP: Sn-TeO2) interfacial layer on the electrical parameters of the Al/p-Si diode. For this aim, (Sn-TeO2) nanostructures were developed by the ultrasound-assisted method, and both their electrical and optical characteristics were investigated by XRD, SEM, EDS, and UV–Vis methods. The bandgap of Sn-TeO2 was found as 4.65 eV from the (αhυ)2 vs (hυ) plot. The main electrical parameters of the Al/p-Si diodes with/ without (PVP: Sn-TeO2) interlayer, such as ideality factor (n), zero-bias barrier height (Φ0), and series resistance (Rs), were calculated by applying and comparing two methods of thermionic emission theory and Cheung’s functions. These results show that the presence of the (PVP: Sn-TeO2 interlayer, along with the increase of Φ0, and the decrease of n and Rs, led to a significant increment in the rectification of MPS when compared to MS diode. The current-transport mechanisms (CTMs) of them were examined through the forward LnIF − LnVF and reverse LnIR − VR0.5 bias currents, and then, the Poole–Frenkel and Schottky field-lowering coefficients (β) were calculated and obtained its value from the theoretical and experimental methods showed that the mechanism of the reverse current of MS and MPS diodes is governing by the Schottky emission and Pool-Frenkel mechanism, respectively.

scholarly journals Structural Properties and Electrical Characteristics of p-n Junctions Based on Kesterite Cu2ZnSnS4 Layers for Thin-Film Solar Cells

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5182
Author(s):  
Igor Perlikowski ◽  
Eunika Zielony ◽  
Teoman Özdal ◽  
Hamide Kavak
Keyword(s):  
Thin Film ◽  
Sol Gel ◽  
Thin Film Solar Cells ◽  
Grain Structure ◽  
Current Transport ◽  
Electrical Characteristics ◽  
Transport Mechanisms ◽  
Device Structure ◽  
Current Voltage ◽  
Scattering Measurements

In the present study, we provide useful data related to one of the most promising materials in thin-film solar cell technologies: Cu2ZnSnS4 (CZTS) kesterite structures. Sol-gel spin coating and chemical bath deposition methods were used to fabricate and further investigate Mo/CZTS/CdS/ZnO/AZO heterostructures. In order to examine the crystal structure of the samples, Raman scattering measurements using two excitation wavelengths (514.5 nm and 785 nm) were performed. Three Raman bands related to CZTS were found, as well as one that had its origin in CdS. By using laser ablation and performing Raman spectroscopy on these modified samples, it was shown that during the manufacturing process a MoS2 interlayer was formed between the CZTS and Mo layers. Our method proved that the CZTS layer in a multilayer device structure fabricated by solution-based methods can be decomposed, and thus a detailed analysis of the layer can be performed. Subsequently, current-voltage curves were investigated in terms of the essential electrical properties of glass/Mo/p-CZTS/n-CdS/ZnO/AZO junctions and occurring current transport mechanisms. Finally, AFM data were acquired to study the surface topography of the studied samples. The images showed that these surfaces had a uniform grain structure.

Two-diode behavior in metal-ferroelectric-semiconductor structures with bismuth titanate interfacial layer

2017 ◽  
Vol 31 (27) ◽  
pp. 1750197 ◽  
Author(s):  
Perihan Durmuş ◽  
Şemsettin Altindal
Keyword(s):  
Conduction Mechanism ◽  
Bismuth Titanate ◽  
Thermionic Emission ◽  
Saturation Current ◽  
Electrical Parameters ◽  
Zero Bias ◽  
Semiconductor Structures ◽  
Current Voltage ◽  
Diode Behavior ◽  
Increasing Temperature

In this study, electrical parameters of the Al/Bi4Ti3O[Formula: see text]/p-Si metal-ferroelectric-semiconductor (MFS) structure and their temperature dependence were investigated using current–voltage (I–V) data measured between 120 K and 300 K. Semi-logarithmic I–V plots of the structure revealed that fabricated structure presents two-diode behavior that leads to two sets of ideality factor, reverse saturation current and zero-bias barrier height (BH) values. Obtained results of these parameters suggest that current conduction mechanism (CCM) deviates strongly from thermionic emission theory particularly at low temperatures. High values of interface states and nkT/q[Formula: see text]−[Formula: see text]kT/q plot supported the idea of deviation from thermionic emission. In addition, [Formula: see text](I)[Formula: see text]−[Formula: see text][Formula: see text](V) plots suggested that CCM varies from one bias region to another and depends on temperature as well. Series resistance values were calculated using Ohm’s law and Cheungs’ functions, and they decreased drastically with increasing temperature.

Temperature Dependent Current-Voltage Characteristics of n-Type Nanocrystalline-FeSi2/p-Type Si Heterojunctions Fabricated by Pulsed Laser Deposition

2013 ◽  
Vol 858 ◽  
pp. 171-176
Author(s):  
Nathaporn Promros ◽  
Ryūhei Iwasaki ◽  
Suguru Funasaki ◽  
Kyohei Yamashita ◽  
Chen Li ◽  
...  
Keyword(s):  
Barrier Height ◽  
Ideality Factor ◽  
Carrier Transport ◽  
Series Resistance ◽  
Thermionic Emission ◽  
Temperature Dependent ◽  
Zero Bias ◽  
Current Voltage ◽  
Current Voltage Characteristics ◽  
P Type

n-Type NC-FeSi2/p-type Si heterojunctions were successfully fabricated by PLD, and their forward current-voltage characteristics were analyzed on the basis of thermionic emission theory (TE) in the temperature range from 300 down to 77 K. With a decrease in the temperature, the ideality factor was increased while the zero-bias barrier height was decreased. The calculated values of ideality factor and barrier height were 3.07 and 0.63 eV at 300 K and 10.75 and 0.23 eV at 77 K. The large value of ideality factor indicated that a tunneling process contributes to the carrier transport mechanisms in the NC-FeSi2 films. The series resistance, which was estimated by Cheungs method, was strongly dependent on temperature. At 300 K, the value of series resistance was 12.44 Ω and it was dramatically enhanced to be 1.71× 105 Ω at 77 K.

Current Transport Mechanisms in CuIn1−xGaxSe2 and CIS Thin-Film Solar Cells on Flexible Stainless Steel Substrates

2001 ◽  
Vol 668 ◽  
Author(s):  
Gaurav A. Naik ◽  
Wayne A. Anderson
Keyword(s):  
Thin Film ◽  
Stainless Steel ◽  
Solar Cells ◽  
Thermionic Emission ◽  
Current Transport ◽  
Transport Mechanisms ◽  
Copper Indium ◽  
Current Voltage ◽  
Cigs Solar Cells ◽  
Steel Substrates

ABSTRACTCopper indium gallium selenide (CIGS) solar cells on thin film stainless steel substrates were evaluated by current-voltage-temperature (IVT) from 150K-350K to determine current transport mechanisms. Both dark and photo data at reverse and low forward voltages exhibited tunneling-like behavior. At intermediate forward voltages, diffusion or thermionic emission are suggested by an ideality factor close to 1.0. At higher currents and voltages there is a trend towards recombination or space change limited behavior.

Parameter Extraction from the Reverse I-V and C-V Characteristics of an Epitaxial p-InP/Au Schottky Diode

1993 ◽  
Vol 318 ◽  
Author(s):  
A. Singh ◽  
P. Cova ◽  
R. A. Masut
Keyword(s):  
Barrier Height ◽  
Schottky Diodes ◽  
Thermionic Emission ◽  
Reverse Current ◽  
Parameter Extraction ◽  
Interface Layer ◽  
Least Square ◽  
Reverse Bias Voltage ◽  
Zero Bias ◽  
Current Voltage

ABSTRACTEpitaxial p-InP/Au Schottky diodes were fabricated by evaporation of Au onto Zn doped epitaxial layers of InP grown by MOVPE, on a highly doped InP substrate. The reverse current-voltage (Ir-Vr) and 1 MHz capacitance-voltage (C-V) characteristics of the Au/p-InP diodes were measured in the temperature range 220-393 K. At all temperatures, soft reverse current-voltage characteristics were observed, which may be due to the decrease in the effective Schottky barrier height (øbr) with the increase of Vr. The voltage dependence of the reverse current was well described in terms of the interface layer thermionic emission (ITE) model which incorporates the effects of applied reverse voltage drop and the transmission coefficient across the interface layer and image force lowering of the barrier height into the thermionic emission theory. A self consistent iteration and least square fitting technique was used to obtain the zero bias barrier height (øbo) and interface layer capacitance (Ci) from the Ir-Vr data. Both, the Ir-Vr and the C-V data were analyzed under the assumption of reverse bias voltage independence of the charge trapped in the interface states, which was supported by our experimental data. The values of øbo obtained from the C-V measurements agreed well with those obtained from the Ir-Vr data for a value of 0.45 AK−2cm−2 for the effective Richardson constant (Aeff).

scholarly journals A Study of a-Sic/C-Si(n) Isotype Heterojunctions

1993 ◽  
Vol 16 (1) ◽  
pp. 55-64 ◽  
Author(s):  
N. Georgoulas ◽  
L. Magafas ◽  
A. Thanailakis
Keyword(s):  
Temperature Dependence ◽  
Crystalline Silicon ◽  
Diffusion Mechanism ◽  
Thermionic Emission ◽  
Reverse Current ◽  
Emission Mechanism ◽  
Drift Diffusion ◽  
Si Substrates ◽  
Current Voltage ◽  
Capacitance Voltage

In the present work a study of the electrical properties of heterojunctions between rf sputtered amorphous silicon carbide (a-SiC) thin films and n-type crystalline silicon (c-Si) substrates is reported. The current-voltage (I-V) and capacitance-voltage (C-V) characteristics, as well as the temperature dependence of the current of a-SiC/c-Si(n) heterojunctions were measured. The I-V characteristics of a-SiC/ c-Si(n) heterojunctions exhibit poor rectification properties, with a high reverse current, at higher temperatures (T > 250K), whereas good rectification properties are obtained at lower temperatures (T < 250K). It was found that the a-SiC/c-Si(n) heterojunctions are isotype, suggesting that-the conductivity of a-SiC is n-type. The temperature dependence of the current (from 185K to 320K) showed that the majority carriers of c-Si(n) (i.e. electrons) are transported from c-Si(n) to a-SiC mainly by the thermionic emission mechanism, or by the drift-diffusion mechanism. From C-V measurements of a-SiC/c-Si(n) heterojunctions the electron affinity of a-SiC was found to be X1= 4.20 ± 0.04 eV. Finally, the a-SiC/ c-Si(n) isotype heterojunctions are expected to be interesting devices as infrared

Investigation of carrier transport mechanisms in the Cu–Zn–Se based hetero-structure grown by sputtering technique

2018 ◽  
Vol 96 (7) ◽  
pp. 816-825 ◽  
Author(s):  
H.H. Güllü ◽  
M. Terlemezoğlu ◽  
Ö. Bayraklı ◽  
D.E. Yıldız ◽  
M. Parlak
Keyword(s):  
Barrier Height ◽  
Carrier Transport ◽  
Thermionic Emission ◽  
Electrical Characterization ◽  
Band Gap Energy ◽  
Zero Bias ◽  
Hetero Structure ◽  
Current Voltage ◽  
P Type

In this paper, we present results of the electrical characterization of n-Si/p-Cu–Zn–Se hetero-structure. Sputtered film was found in Se-rich behavior with tetragonal polycrystalline nature along with (112) preferred orientation. The band gap energy for direct optical transitions was obtained as 2.65 eV. The results of the conductivity measurements indicated p-type behavior and carrier transport mechanism was modelled according to thermionic emission theory. Detailed electrical characterization of this structure was carried out with the help of temperature-dependent current–voltage measurements in the temperature range of 220–360 K, room temperature, and frequency-dependent capacitance–voltage and conductance-voltage measurements. The anomaly in current–voltage characteristics was related to barrier height inhomogeneity at the interface and modified by the assumption of Gaussian distribution of barrier height, in which mean barrier height and standard deviation at zero bias were found as 2.11 and 0.24 eV, respectively. Moreover, Richardson constant value was determined as 141.95 Acm−2K−2 by means of modified Richardson plot.

Current-transport mechanism in Au/V-doped PVC+TCNQ/p-Si structures

2015 ◽  
Vol 29 (13) ◽  
pp. 1550076 ◽  
Author(s):  
H. Tecimer ◽  
Ö. Vural ◽  
A. Kaya ◽  
Ş. Altındal
Keyword(s):  
Temperature Coefficient ◽  
Transport Mechanism ◽  
Forward Bias ◽  
Thermionic Emission ◽  
Negative Temperature ◽  
Positive Temperature ◽  
Current Transport ◽  
Insulator Layer ◽  
Zero Bias ◽  
Current Transport Mechanism

The forward and reverse bias current–voltage (I–V) characteristics of Au/V-doped polyvinyl chloride+Tetracyanoquino dimethane/porous silicon (PVC+TCNQ/p-Si) structures have been investigated in the temperature range of 160–340 K. The zero bias or apparent barrier height (BH) (Φ ap = Φ Bo ) and ideality factor (n ap = n) were found strongly temperature dependent and the value of n ap decreases, while the Φ ap increases with the increasing temperature. Also, the Φ ap versus T plot shows almost a straight line which has positive temperature coefficient and it is not in agreement with the negative temperature coefficient of ideal diode or forbidden bandgap of Si (α Si = -4.73×10-4 eV/K ). The high value of n cannot be explained only with respect to interfacial insulator layer and interface traps. In order to explain such behavior of Φ ap and n ap with temperature, Φ ap Versus q/2kT plot was drawn and the mean value of (Φ Bo ) and standard deviation (σs) values found from the slope and intercept of this plot as 1.176 eV and 0.152 V, respectively. Thus, the modified ( ln (Io/T2)-(qσs)2/2(kT)2 versus (q/kT) plot gives the Φ Bo and effective Richardson constant A* as 1.115 eV and 31.94 A ⋅(cm⋅K)-2, respectively. This value of A*( = 31.94 A⋅( cm ⋅K)-2) is very close to the theoretical value of 32 A ⋅(cm⋅K)-2 for p-Si. Therefore, the forward bias I–V–T characteristics confirmed that the current-transport mechanism (CTM) in Au/V-doped PVC+TCNQ/p-Si structures can be successfully explained in terms of the thermionic emission (TE) mechanism with a Gaussian distribution (GD) of BHs at around mean BH.

Sign in / Sign up

Export Citation Format

Share Document