A Case Study of Fracture Law and Stress Distribution Characteristics of Surrounding Rock of Working Face in Deep Mines

2019 ◽  
Vol 37 (4) ◽  
pp. 2935-2948 ◽  
Author(s):  
Xianfeng Shi ◽  
Xingkai Zhang ◽  
Fuxing Jiang
Keyword(s):  
Stress Distribution ◽  
Surrounding Rock ◽  
Distribution Characteristics ◽  
Working Face

scholarly journals Comprehensive technical support for safe mining in ultra-close coal seams: A case study

2021 ◽  
pp. 014459872110093
Author(s):  
Wei Zhang ◽  
Jiawei Guo ◽  
Kaidi Xie ◽  
Jinming Wang ◽  
Liang Chen ◽  
...  
Keyword(s):  
Coal Seam ◽  
Technical Support ◽  
Surrounding Rock ◽  
Coal Seams ◽  
Deformation Control ◽  
Hard Roof ◽  
Working Face ◽  
Close Coal Seams ◽  
Safe Mining

In order to mine the coal seam under super-thick hard roof, improve the utilization rate of resources and prolong the remaining service life of the mine, a case study of the Gaozhuang Coal Mine in the Zaozhuang Mining Area has been performed in this paper. Based on the specific mining geological conditions of ultra-close coal seams (#3up and #3low coal seams), their joint systematic analysis has been performed, with the focus made in the following three aspects: (i) prevention of rock burst under super-thick hard roof, (ii) deformation control of surrounding rock of roadways in the lower coal seam, and (iii) fire prevention in the goaf of working face. Given the strong bursting tendency observed in upper coal seam and lower coal seam, the technology of preventing rock burst under super-thick hard roof was proposed, which involved setting of narrow section coal pillars to protect roadways and interleaving layout of working faces. The specific supporting scheme of surrounding rock of roadways in the #3low1101 working face was determined, and the grouting reinforcement method of local fractured zones through Marithan was further proposed, to ensure the deformation control of surrounding rock of roadways in lower coal seams. The proposed fire prevention technology envisaged goaf grouting and spraying to plug leaks, which reduced the hazard of spontaneous combustion of residual coals in mined ultra-close coal seams. The technical and economic improvements with a direct economic benefit of 5.55 million yuan were achieved by the application of the proposed comprehensive technical support. The research results obtained provide a theoretical guidance and technical support of safe mining strategies of close coal seams in other mining areas.

scholarly journals Mine Pressure Behavior Characteristics and Control Methods of a Reused Entry that Was Formed by Roof Cutting: A Case Study

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Yajun Wang ◽  
Haosen Wang ◽  
Manchao He ◽  
Qi Wang ◽  
Yafei Qiao ◽  
...  
Keyword(s):  
Deformation Zone ◽  
Dynamic Pressure ◽  
Field Application ◽  
Surrounding Rock ◽  
Mine Pressure ◽  
Stress Increase ◽  
Severe Deformation ◽  
Working Face ◽  
Roof Deformation

Noncoal pillar mining with automatic formation of a roadway is a new coal mining method that is tailored to improve the coal resource recovery rate and reduce the investment in roadway tunneling. Using this proposed method, a reuse entry is formed by roof cutting instead of tunneling. In this paper, the S1201-II working face of the Ningtiaota Coal Mine was used as a case study. The stress distribution of surrounding rock and the roof deformation characteristics of the reused entry during the mining process of the second working face were studied through FLAC3D numerical simulations combined with field measurements. The results indicate that the zone close to the reused entry led to higher stress in advance. If this stress is superimposed with the lateral pressure of the adjacent mined working face, it will be more difficult to maintain the reused entry. In the engineering case study described here, the reused entry created a stress increase zone and a severe deformation zone in the range of 0–80 m in front of the working face, and its range was approximately 37.5% larger than an ordinary entry. The stress peak in the stress increase zone increased by approximately 34.7% over that of an ordinary entry. The maximum amount of deformation within the severe deformation zone increased by 94.4% over that of an ordinary entry. To properly control the surrounding rock stress and deformation of the reused entry, a dynamic pressure bearing support in front of the working face with adaptability to the large roof deformation and high support strength is proposed here. Field application results showed that the final roof deformation with the dynamic pressure bearing support can be satisfactorily controlled within 110∼130 mm. These findings can provide a reference for researchers and field engineering technicians when engaging in the support work of reused entry.

scholarly journals Research on Failure Mechanism and Strengthening of Broken Roadway Affected by Upper Coal Pillar

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Fulian He ◽  
Zheng Zheng ◽  
Hengzhong Zhu ◽  
Bo Yang
Keyword(s):  
Stress Distribution ◽  
Failure Mechanism ◽  
Coal Pillar ◽  
Control Area ◽  
Surrounding Rock ◽  
Horizontal Line ◽  
Protective Function ◽  
Working Face ◽  
Coal Pillars ◽  
Roadway Deformation

The principal stress difference is introduced as a new evaluation index in order to better understand the failure mechanism of roadways affected by upper coal pillars and characterize failure of rock mass. Compared with traditional methods, it facilitates quantitative analysis. Moreover, we combine the semiplane theory and we obtain the stress distribution on the coal pillar’s bedrock and the strengthening control area from the “change point” position along a 21 m horizontal line. The influence of multiple stresses induced from mining on a roadway is analyzed. It is found that rock failure is most likely while mining the 051606 working face, followed by mining the 051604 working face, and the stress influence on the upper pillar has the lowest failure probability. In addition, based on the asymmetry of the surrounding rock stress distribution, this study proposes strengthening control technology of surrounding rock on the basis of a highly stressed bolting support and anchor cable, adding to the steel ladder beam, steel mesh, and shed support’s protective function to the roadway’s roof and ribs. Finally, through field observations, it is concluded that the roadway deformation is within the controllable range.

scholarly journals Numerical Investigation of Gob-Side Entry Retaining through Precut Overhanging Hard Roof to Control Rockburst

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Xiaoming Sun ◽  
Li Gan ◽  
Zhao Chengwei ◽  
Tang Jianquan ◽  
He Manchao ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Abutment Pressure ◽  
Feasibility Studies ◽  
Main Roof ◽  
Surrounding Rock ◽  
Distribution Characteristics ◽  
Hard Roof ◽  
Working Face ◽  
Stress Fluctuation ◽  
Peak Value

Gob-side entry retaining through precut overhanging hard roof (GERPOHR) method is one of the commonly used methods for nonpillar mining. However, feasibility studies of controlling rockburst by this method are few. Rockburst occurs in hard thick strata with a higher probability, larger scale, and higher risk. To better understand the GERPOHR method is beneficial for rockburst mitigation. In this paper, the design of GERPOHR was first introduced. And the layout of the working face was optimized. Then, based on the numerical simulation, the stress and displacement distribution characteristics were compared under the condition of conventional mining and GERPOHR method. The research shows that the intervals of main roof weighting could be decreased through the precut overhanging hard roof method. And the peak value of abutment pressure decreased. Meanwhile, the energy accumulation and the stress fluctuation could be alleviated in roadway surrounding rock.

Stress Shell Mechanical Mechanism of Fully-Mechanized Face Enhancing the Upper Limit for Coal Mining and Risk Analysis of Support Break-Off

2012 ◽  
Vol 524-527 ◽  
pp. 466-470
Author(s):  
Jun Ling Hou ◽  
Yan Sun
Keyword(s):  
Stress Distribution ◽  
Coal Seam ◽  
Coal Mining ◽  
Surrounding Rock ◽  
Mechanical Environment ◽  
Upper Limit ◽  
Working Face ◽  
Distribution Rule ◽  
Geological Conditions ◽  
Mining Face

Based on the geological conditions and specific mining technology conditions of the 11014 mining face of Panbei mine in HuaiNan mining group ,using the FLAC3D software, simulate the stress distribution rule and disruption field distribution rule of surrounding rock of Fully-Mechanized face enhancing the upper limit for coal mining along the tendency and trend of coal seam by different mining speed of 6 m/d, 4 m/d and 2 m/d. draw the conclusion that enhancing the mining speed can alleviate the pressure of the working face ,improve the working face mechanical environment,and reduce the extent of the failure field.It provides the theory basis and reference for Fully-Mechanized face enhancing the upper limit for coal mining under similar conditions.

The Research on Abutment Stress Distribution and Fracture Characteristics of Coal Seam in Longwall Face

2011 ◽  
Vol 361-363 ◽  
pp. 103-107
Author(s):  
Chuan Ming Li
Keyword(s):  
Stress Distribution ◽  
Coal Seam ◽  
Surrounding Rock ◽  
Geometrical Shape ◽  
Horizontal Distance ◽  
Site Testing ◽  
Fracture Characteristics ◽  
Working Face ◽  
Coal Wall ◽  
Overlying Strata

The abutment stress results from the load coming from overlying strata above the influence range of abutment stress and the load which coming from overlying strata above the stress shell passed by the shell. Through the mechanical calculation,this paper analyzed abutment stress distribution and fracture characteristics of coal seam resulted from the load of overlying strata passed by stress shell which exists in surrounding rock of working face, and obtained the laws of abutment stress distribution and fracture in coal seam in combination with numerical simulation and site testing. The characteristics of abutment stress distribution and fracture are related to the geometrical shape of the stress shell, such as height of the stress shell, horizontal distance between top of stress shell and coal wall,and width of stress shell skewback.

scholarly journals Stability Control of a Goaf-Side Roadway under the Mining Disturbance of an Adjacent Coal Working Face in an Underground Mine

2019 ◽  
Vol 11 (22) ◽  
pp. 6398
Author(s):  
Houqiang Yang ◽  
Changliang Han ◽  
Nong Zhang ◽  
Changlun Sun ◽  
Dongjiang Pan ◽  
...  
Keyword(s):  
Stress Distribution ◽  
Stability Control ◽  
Surrounding Rock ◽  
Engineering Practice ◽  
Key Strata ◽  
Coal Recovery ◽  
Working Face ◽  
Underground Coal Mines ◽  
Mining Disturbance ◽  
The Stability

Goaf-side roadway driving could not only notably reduce the loss of coal resources and improve the coal recovery rates, but also greatly mitigate the imbalance between excavation speed and production needs, which are able to prolong the service life of the mine and are pivotal to sustainable and efficient development of underground coal mines. However, it is difficult to control the stability of the goaf-side roadway, especially under mining disturbance of another adjacent coal working face. In order to control the stability of the goaf-side roadway, Haulageway 1513 in the Xinyi Coal Mine of China, under mining disturbance, theoretical analysis, numerical simulation, and engineering practice were carried out to reveal the mechanism of overburden key strata fracture, stress distribution, and deformation characteristics of the surrounding rock of the goaf-side roadway due to mining disturbance. Results showed that some key strata above Goaf 1512 did not fracture due to the influence of the strata caving angles. However, these key strata would fracture and break into rock blocks when suffering from mining disturbance of the adjacent coal working face, which changed the stress distribution and increased the deformations of the surrounding rock of the goaf-side roadway. The combined techniques of pressure relief and bolt support were proposed and carried out to control the stability of the goaf-side roadway. Engineering practice indicated that the maximum deformations of the roof and sidewall-to-sidewall were 220 mm and 470 mm, respectively. The deformations of the goaf-side roadway under mining disturbance were efficiently controlled.

Surrounding Rock Convergence Rule along the Working Face Tendency of Recovery Room

2014 ◽  
Vol 962-965 ◽  
pp. 352-356
Author(s):  
Zhigang Wu ◽  
Wen Zhou Li
Keyword(s):  
Stress Distribution ◽  
Recovery Room ◽  
Coal Pillar ◽  
Surrounding Rock ◽  
Rock Deformation ◽  
Working Face ◽  
Deformation Mechanics ◽  
Surrounding Rock Deformation ◽  
Moving Speed

Recovery room could ensure the returning safety of working face equipment, improve mining and moving speed efficiency. Surrounding rock of working face will be distributed after recovery room driving, surrounding rock convergence drastically, and mining influence surrounding rock of recovery room also. Stress distribution around recovery room complex. Surrounding rock deformation rule along tendency of working face was studied by filed measurement in Sihe cola mine of the Jincheng coal district in China. It reveals surrounding rock deformation mechanics during coal pillar of working face through.

scholarly journals Study on strata behavior law of deep inclined coal seam

2021 ◽  
Vol 248 ◽  
pp. 03031
Author(s):  
Chen Zhengwen
Keyword(s):  
Numerical Simulation ◽  
Stress Distribution ◽  
Surrounding Rock ◽  
Rock Deformation ◽  
Coal Seams ◽  
Working Face ◽  
Support Resistance ◽  
Strata Behavior ◽  
The Law ◽  
Surrounding Rock Deformation

In order to understand and grasp the law of roof pressure on the working face of deep inclined coal seams, the law of support resistance distribution, the law of leading support stress distribution and the law of surrounding rock deformation of the two roadways, the 94101 working face of Zhangshuanglou Coal Mine was taken as the engineering background. Through a combination of field measurement, numerical simulation, theoretical analysis, etc, this paper analyzes the laws of roof migration and rock pressure manifestation in deep inclined coal seams.

Sign in / Sign up

Export Citation Format

Share Document