scholarly journals Application of calorimetry and other thermal methods in the studies of granulated blast furnace slag from the old storage yards as supplementary cementitious material

2021 ◽  
Author(s):  
W. Nocuń-Wczelik ◽  
W. Pacierpnik ◽  
E. Kapeluszna
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Cement Clinker ◽  
Thermal Methods ◽  
Granulated Blast Furnace Slag ◽  
Long Time ◽  
Current Production ◽  
European Standards ◽  
Cementing Material ◽  
Furnace Slag

AbstractThe calorimetric and DTA/TG measurements were applied in testing the effect of granulated blast furnace slag originated from the storage yards of different age, added as a supplementary cementing material to the Portland cement clinker. The studies were performed with aim to evaluate the kinetics of cement hydration and the modification of hydrated paste composition in the presence of additive. The material after 20-year storage, the crushed slag after approximately 2-years storage and the new slag from the current production in the metallurgical plant were used. The slag percentage was 5 ÷ 50%. The addition of granulated blast furnace slag stored for a long time affects the standard properties of cement reducing the compressive strength at longer maturing and with the percentage of additive. This is related mainly to the reduction in the vitreous component. However, at the additive content up to 50% the binder complying with the requirements of the relevant European standards for common cements could be produced. Basing on the results of TG measurements the role of calcium carbonate, being the product resulting from the slag weathering process, acting as a grindability and setting/hardening modifying agent, was highlighted.

Utilization of Ground Granulated Blast-Furnace Slag Seed Crystal in Eco-Cement

2011 ◽  
Vol 250-253 ◽  
pp. 870-874
Author(s):  
Hong Mei Ai ◽  
Jing Wei ◽  
Jun Ying Bai ◽  
Pu Guang Lu
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Sintering Temperature ◽  
Seed Crystal ◽  
Cement Clinker ◽  
X Ray Diffraction ◽  
Cement Pastes ◽  
Granulated Blast Furnace Slag ◽  
Lower Temperature ◽  
Furnace Slag

Eco-cement produced from waste concrete was proved to be feasible in early research. The seed crystal of ground granulated blast furnace slag (GGBS) was utilized in this research to lower the sintering temperature of eco-cement clinker. The mineral compositions of clinker with GGBS seed crystal was analyzed by X-ray diffraction (XRD), and the mechanical properties of eco-cement with GGBS seed crystal was also tested. Four main cement minerals were all observed in eco-cement clinker and the compressive strength of the eco-cement pastes can approach to about 66 MPa at 28 curing days. The results showed that GGBS seed crystal was favourable for the formation of cement minerals at a lower temperature. It can help reduce by about 50~100°C for the sintering process of cement clinker. Content of GGBS seed crystal should better be in the rage of 5%~8%, and the suitable sintering temperature should be 1350°C.

scholarly journals Investigation of Mechanical Properties, Durability and Microstructure of Low-Clinker High-Performance Concretes Incorporating Ground Granulated Blast Furnace Slag, Siliceous Fly Ash and Silica Fume

2021 ◽  
Vol 11 (2) ◽  
pp. 830
Author(s):  
Katarzyna Konieczna ◽  
Karol Chilmon ◽  
Wioletta Jackiewicz-Rek
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
High Performance ◽  
Cement Clinker ◽  
Water Penetration ◽  
Granulated Blast Furnace Slag ◽  
Portland Cement Clinker ◽  
Furnace Slag

The main assumption of eco-efficient High-Performance Concrete (HPC) design is the reduction of Portland cement clinker content without negatively affecting the composite’s mechanical and durability properties. In this paper, three low-clinker HPC mixtures incorporating slag cement (CEM III/B as per EN 197-1) and Supplementary Cementitious Materials (SCMs)—Ground Granulated Blast Furnace Slag (GGBFS), Siliceous Fly Ash (SFA) and Silica Fume (SF)—were designed. The maximum amount of Portland cement clinker from CEM III/B varied from 64 to 116 kg in 1 m3 of concrete mix. The compressive strength of HPC at 2, 7, 14, 28, 56, 90 days, and 2 years after casting, as well as the modulus of elasticity on 2-year-old specimens, was tested. The depth of water penetration under pressure and internal frost resistance in freeze–thaw tests were evaluated after 56 days of curing. Additionally, the concrete pH value tests were performed. The microstructure of 2-year-old HPC specimens was analyzed using Scanning Electron Microscopy (SEM). The research proved that it is possible to obtain low-clinker High-Performance Concretes that reach compressive strength of 76–92 MPa after 28 days of curing, show high values of modulus of elasticity (49–52 GPa) as well as increased resistance to frost and water penetration under pressure.

scholarly journals Incorporation of Cement Bypass Dust in Hydraulic Road Binder

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 41
Author(s):  
Nadezda Stevulova ◽  
Julius Strigac ◽  
Jozef Junak ◽  
Eva Terpakova ◽  
Marian Holub
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Cement Clinker ◽  
Cement Kiln ◽  
Standard Requirement ◽  
Initial Setting Time ◽  
Granulated Blast Furnace Slag ◽  
Initial Setting ◽  
Furnace Slag

This article describes utilization of a cement kiln bypass dust utilization as an added component in a hydraulic road binder. Three experimental binder mixes (BM1–BM3) with variation in the composition of the main constituents (cement clinker, ground limestone and ground granulated blast furnace slag) and constant content of bypass dust (10%) were prepared under laboratory conditions. The properties of binder constituents, fresh experimental binder mixes and hardened specimens were tested according to STN EN 13282-2 for a normal hardening hydraulic road binder. The physical and chemical properties of all binder mixes (fineness: +90 µm ≤ 15 wt.%; SO3 content: <4 wt.%) met the standard requirements. The bypass dust addition led to an increase in the water content for standard consistency of cement mixes (w/c = 0.23) and to a shortening of the initial setting time for two experimental blended cement pastes (BM1 and BM3) compared with the value required by the standard. Only BM2 with the lowest SO3 content (0.363 wt.%) and the highest percentage of granulated blast furnace slag (9.5 wt.%) and alkalis (Na2O and K2O content of 5.9 wt.%) in the binder mix met the standard value for the initial setting time (≥150 min). The results of compressive strength testing of experimental specimens after 56 days of hardening (59.2–63.9 MPa) indicate higher values than the upper limit of the standard requirement for the N4 class (≥32.5; ≤52.5 MPa).

scholarly journals Granulated Blast-Furnace Slag and Coal Fly Ash Ternary Portland Cements Optimization

2020 ◽  
Vol 12 (14) ◽  
pp. 5783 ◽  
Author(s):  
Rosa Abnelia Rivera ◽  
Miguel Ángel Sanjuán ◽  
Domingo Alfonso Martín
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Portland Cement ◽  
Blast Furnace Slag ◽  
Coal Fly Ash ◽  
Cement Clinker ◽  
Portland Cements ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Granulated blast-furnace slag (GBFS) and coal fly ash (CFA) are two well-known constituents in Portland cements. Ternary Portland cements (GBFS-CFA-K) provide environmental advantages by reducing Portland cement clinker (K) production and, therefore, promote lower CO2 emissions. Nevertheless, both of them cause a delay in the compressive strength gain. Given that, the early compressive strength for both constituents is low, but they improve the compressive strength at medium and later ages as consequence of the pozzolanic reaction. In this paper, a full factorial design with two levels was developed for the mortar compressive strength estimation at 2, 7 and 28 days. Mortar prisms made with 25% and 40% of granulated blast-furnace slag (GBFS) and/or coal fly ash (CFA) were tested. The effects of the interaction between GBFS and CFA on the compressive strength development of ternary Portland cement mortars were reported. Results show that the contribution of both cement constituents to the ternary mortar mix reduces the compressive strength for all the tested ages. Nevertheless, the finer the GBFS, the better ternary cement performance was achieved, showing that the synergistic effect is more effective when the finer GBFS is used, probably due to a more adequate particle size distribution. Finally, a relationship between compressive strength, fineness, GBFS content and CFA content was found for each age.

Canadian use of ground granulated blast-furnace slag as a supplementary cementing material for enhanced performance of concrete

2000 ◽  
Vol 27 (4) ◽  
pp. 754-760 ◽  
Author(s):  
R Doug Hooton
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Large Scale ◽  
Heat Of Hydration ◽  
Chloride Ingress ◽  
Blended Cements ◽  
Setting Times ◽  
Granulated Blast Furnace Slag ◽  
Cementing Material ◽  
Furnace Slag

The performance of concrete, in terms of its placeability, physical properties, and its durability, can be enhanced by the use of slag-blended cements or separately added ground granulated blast-furnace slag. It also has advantages for architectural purposes due to the whiteness it imparts to concrete. Properly proportioned and cured slag concretes will control deleterious alkali-silica reactions, impart sulphate resistance, greatly reduce chloride ingress, and reduce heat of hydration. Setting times and early age strengths can be controlled through appropriate proportioning, while later age properties are typically enhanced. CSA and ASTM standards cover both slag-blended cements (CSA A362; ASTM C595; ASTM C1157) and slag as a supplementary cementing material (CSA A23.5; ASTM C989). Since Lafarge introduced the first large-scale slag grinding plant near Hamilton in 1976, slag has become the predominant supplementary cementing material in Ontario. Recently, its availability in the U.S. has expanded dramatically.Key words: blast-furnace slag, concrete performance, supplementary cementing material.

scholarly journals Application of fly ash/granulated blast-furnace slag cementing material for immobilization of Pb2+

2018 ◽  
Vol 175 ◽  
pp. 01020 ◽  
Author(s):  
Li Chao ◽  
Zhao Feng-qing
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Low Cost ◽  
Hydration Products ◽  
Experimental Conditions ◽  
Granulated Blast Furnace Slag ◽  
Carbide Slag ◽  
Cementing Material ◽  
Furnace Slag

Based on activation and synergistic effect among various materials, a low-cost cementing material. FGC binder, was prepared by using fly ash. granulated blast-furnace slag (BFS). carbide slag and compound activator. The results showed that the immobilization efficiency of FGC binder for Pb2+: is higher than that of OPC cement. The hydration products and mechanism of immobilization were analyzed by using XRD. The major products of FGC binder are C-S-H, C-A-H. ettringite and zeolite-like materials. Under the experimental conditions, the Pb2+ curing efficiency of FGC binder is 1.04 ~ 1.24 times that of ordinary Portland cement.

The Influence of the Properties of the Material Used for Obtaining Geopolymers on Their Structure and Compressive Strength

2017 ◽  
Vol 68 (6) ◽  
pp. 1182-1187
Author(s):  
Ilenuta Severin ◽  
Maria Vlad
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Wheat Straw ◽  
Red Mud ◽  
Blast Furnace Slag ◽  
Complex Structure ◽  
Point Of View ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag ◽  
Straw Ash

This article presents the influence of the properties of the materials in the geopolymeric mixture, ground granulated blast furnace slag (GGBFS) + wheat straw ash (WSA) + uncalcined red mud (RMu), and ground granulated blast furnace slag + wheat straw ash + calcined red mud (RMc), over the microstructure and mechanical properties of the synthesised geopolymers. The activation solutions used were a NaOH solution with 8M concentration, and a solution realised from 50%wt NaOH and 50%wt Na2SiO3. The samples were analysed: from the microstructural point of view through SEM microscopy; the chemical composition was determined through EDX analysis; and the compressive strength tests was done for samples tested at 7 and 28 days, respectively. The SEM micrographies of the geopolymers have highlighted a complex structure and an variable compressive strength. Compressive strength varied from 24 MPa in the case of the same recipe obtained from 70% of GGBFS + 25% WSA +5% RMu, alkaline activated with NaOH 8M (7 days testing) to 85 MPa in the case of the recipe but replacing RMu with RMc with calcined red mud, alkaline activated with the 50%wt NaOH and 50%wt Na2SiO3 solution (28 days testing). This variation in the sense of the rise in compressive strength can be attributed to the difference in reactivity of the materials used in the recipes, the curing period, the geopolymers structure, and the presence of a lower or higher rate of pores, as well as the alkalinity and the nature of the activation solutions used.

scholarly journals Effect of Flue Gas Desulfurization Gypsum on the Properties of Calcium Sulfoaluminate Cement Blended with Ground Granulated Blast Furnace Slag

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 382 ◽  
Author(s):  
Danying Gao ◽  
Zhenqing Zhang ◽  
Yang Meng ◽  
Jiyu Tang ◽  
Lin Yang
Keyword(s):  
Blast Furnace ◽  
Mechanical Strength ◽  
Flue Gas ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Flue Gas Desulfurization ◽  
Calcium Sulfoaluminate Cement ◽  
Calcium Sulfoaluminate ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

This work aims to investigate the effect of additional flue gas desulfurization gypsum (FGDG) on the properties of calcium sulfoaluminate cement (CSAC) blended with ground granulated blast furnace slag (GGBFS). The hydration rate, setting time, mechanical strength, pore structure and hydration products of the CSAC-GGBFS mixture containing FGDG were investigated systematically. The results show that the addition of FGDG promotes the hydration of the CSAC-GGBFS mixture and improves its mechanical strength; however, the FGDG content should not exceed 6%.

scholarly journals Effect of Mineral Admixtures on the Performance of Low-Quality Recycled Aggregate Concrete

Crystals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 596
Author(s):  
Yasuhiro Dosho
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Mineral Admixtures ◽  
Structural Concrete ◽  
Aggregate Concrete ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

To improve the application of low-quality aggregates in structural concrete, this study investigated the effect of multi-purpose mineral admixtures, such as fly ash and ground granulated blast-furnace slag, on the performance of concrete. Accordingly, the primary performance of low-quality recycled aggregate concrete could be improved by varying the replacement ratio of the recycled aggregate and using appropriate mineral admixtures such as fly ash and ground granulated blast-furnace slag. The results show the potential for the use of low-quality aggregate in structural concrete.

Sign in / Sign up

Export Citation Format

Share Document