scholarly journals A broadbanded pressure differential wave energy converter based on dielectric elastomer generators

2021 ◽  
Author(s):  
Michele Righi ◽  
Giacomo Moretti ◽  
David Forehand ◽  
Lorenzo Agostini ◽  
Rocco Vertechy ◽  
...  
Keyword(s):  
Wave Energy ◽  
Large Deformations ◽  
Dielectric Elastomer ◽  
Wave Energy Converter ◽  
Pressure Differential ◽  
Design Stage ◽  
Small Scale ◽  
Energy Converter ◽  
Wide Range ◽  
The Waves

AbstractDielectric elastomer generators (DEGs) are a promising option for the implementation of affordable and reliable sea wave energy converters (WECs), as they show considerable promise in replacing expensive and inefficient power take-off systems with cheap direct-drive generators. This paper introduces a concept of a pressure differential wave energy converter, equipped with a DEG power take-off operating in direct contact with sea water. The device consists of a closed submerged air chamber, with a fluid-directing duct and a deformable DEG power take-off mounted on its top surface. The DEG is cyclically deformed by wave-induced pressure, thus acting both as the power take-off and as a deformable interface with the waves. This layout allows the partial balancing of the stiffness due to the DEG’s elasticity with the negative hydrostatic stiffness contribution associated with the displacement of the water column on top of the DEG. This feature makes it possible to design devices in which the DEG exhibits large deformations over a wide range of excitation frequencies, potentially achieving large power capture in a wide range of sea states. We propose a modelling approach for the system that relies on potential-flow theory and electroelasticity theory. This model makes it possible to predict the system dynamic response in different operational conditions and it is computationally efficient to perform iterative and repeated simulations, which are required at the design stage of a new WEC. We performed tests on a small-scale prototype in a wave tank with the aim of investigating the fluid–structure interaction between the DEG membrane and the waves in dynamical conditions and validating the numerical model. The experimental results proved that the device exhibits large deformations of the DEG power take-off over a broad range of monochromatic and panchromatic sea states. The proposed model demonstrates good agreement with the experimental data, hence proving its suitability and effectiveness as a design and prediction tool.

scholarly journals Experimental Analysis of a Novel Adaptively Counter-Rotating Wave Energy Converter for Powering Drifters

2019 ◽  
Vol 7 (6) ◽  
pp. 171 ◽  
Author(s):  
Guoheng Wu ◽  
Zhongyue Lu ◽  
Zirong Luo ◽  
Jianzhong Shang ◽  
Chongfei Sun ◽  
...  
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Irregular Waves ◽  
Surface Velocity ◽  
Small Scale ◽  
Power Constraint ◽  
Energy Converter ◽  
Wave Tank ◽  
Wide Range ◽  
Rotating Wave

Nowadays, drifters are used for a wide range of applications for researching and exploring the sea. However, the power constraint makes it difficult for their sampling intervals to be smaller, meaning that drifters cannot transmit more accurate measurement data to satellites. Furthermore, due to the power constraint, a modern Surface Velocity Program (SVP) drifter lives an average of 400 days before ceasing transmission. To overcome the power constraint of SVP drifters, this article proposes an adaptively counter-rotating wave energy converter (ACWEC) to supply power for drifters. The ACWEC has the advantages of convenient modular integration, simple conversion process, and minimal affection by the crucial sea environment. This article details the design concept and working principle, and the interaction between the wave energy converter (WEC) and wave is presented based on plane wave theory. To verify the feasibility of the WEC, the research team carried out a series of experiments in a wave tank with regular and irregular waves. Through experiments, it was found that the power and efficiency of the ACWEC are greatly influenced by parameters such as wave height and wave frequency. The maximum output power of the small scale WEC in a wave tank is 6.36 W, which allows drifters to detect ocean data more frequently and continuously.

scholarly journals Modelling and testing of a wave energy converter based on dielectric elastomer generators

2019 ◽  
Vol 475 (2222) ◽  
pp. 20180566 ◽  
Author(s):  
Giacomo Moretti ◽  
Gastone Pietro Rosati Papini ◽  
Luca Daniele ◽  
David Forehand ◽  
David Ingram ◽  
...  
Keyword(s):  
Wave Energy ◽  
Large Scale ◽  
Dielectric Elastomer ◽  
Wave Energy Converter ◽  
Irregular Waves ◽  
System Response ◽  
Small Scale ◽  
Energy Converter ◽  
Operational Conditions ◽  
Analysis And Design

This paper introduces the analysis and design of a wave energy converter (WEC) that is equipped with a novel kind of electrostatic power take-off system, known as dielectric elastomer generator (DEG). We propose a modelling approach which relies on the combination of nonlinear potential-flow hydrodynamics and electro-hyperelastic theory. Such a model makes it possible to predict the system response in operational conditions, and thus it is employed to design and evaluate a DEG-based WEC that features an effective dynamic response. The model is validated through the design and test of a small-scale prototype, whose dynamics is tuned with waves at tank-scale using a set of scaling rules for the DEG dimensions introduced here in order to comply with Froude similarity laws. Wave-tank tests are conducted in regular and irregular waves with a functional DEG system that is controlled using a realistic prediction-free strategy. Remarkable average performance in realistically scaled sea states has been recorded during experiments, with peaks of power output of up to 3.8 W, corresponding to hundreds of kilowatts at full-scale. The obtained results demonstrated the concrete possibility of designing DEG-based WEC devices that are conceived for large-scale electrical energy production.

scholarly journals Multi-Mode Wave Energy Converter Design Optimisation Using an Improved Moth Flame Optimisation Algorithm

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3737
Author(s):  
Mehdi Neshat ◽  
Nataliia Sergiienko ◽  
Seyedali Mirjalili ◽  
Meysam Majidi Nezhad ◽  
Giuseppe Piras ◽  
...  
Keyword(s):  
Wave Energy ◽  
Wave Energy Converter ◽  
Total Power ◽  
Energy Converter ◽  
Wave Regime ◽  
Optimisation Algorithm ◽  
Wide Range ◽  
Evolutionary Optimisation ◽  
Optimisation Methods ◽  
Optimisation Algorithms

Ocean renewable wave power is one of the more encouraging inexhaustible energy sources, with the potential to be exploited for nearly 337 GW worldwide. However, compared with other sources of renewables, wave energy technologies have not been fully developed, and the produced energy price is not as competitive as that of wind or solar renewable technologies. In order to commercialise ocean wave technologies, a wide range of optimisation methodologies have been proposed in the last decade. However, evaluations and comparisons of the performance of state-of-the-art bio-inspired optimisation algorithms have not been contemplated for wave energy converters’ optimisation. In this work, we conduct a comprehensive investigation, evaluation and comparison of the optimisation of the geometry, tether angles and power take-off (PTO) settings of a wave energy converter (WEC) using bio-inspired swarm-evolutionary optimisation algorithms based on a sample wave regime at a site in the Mediterranean Sea, in the west of Sicily, Italy. An improved version of a recent optimisation algorithm, called the Moth–Flame Optimiser (MFO), is also proposed for this application area. The results demonstrated that the proposed MFO can outperform other optimisation methods in maximising the total power harnessed from a WEC.

A Joint Numerical and Experimental Study of a Surging Point Absorbing Wave Energy Converter (WRASPA)

2009 ◽  
Author(s):  
Majid A. Bhinder ◽  
Clive G. Mingham ◽  
Derek M. Causon ◽  
Mohammad T. Rahmati ◽  
George A. Aggidis ◽  
...  
Keyword(s):  
Wave Energy ◽  
Informed Choice ◽  
Wave Energy Converter ◽  
Body Motion ◽  
Numerical Dissipation ◽  
Small Scale ◽  
Linear Wave ◽  
Energy Converter ◽  
Non Linear ◽  
Experimental Project

This paper presents the findings from using several commercial computational fluid dynamics codes in a joint numerical and experimental project to simulate WRASPA, a new wave energy converter (WEC) device. A series of fully 3D non-linear simulations of WRASPA are presented. Three commercial codes STAR-CCM, CFX and FLOW-3D are considered for simulating the WRASPA device and final results are presented based on the use of Flow-3D. Results are validated by comparison to experimental data obtained from small scale tank tests undertaken at Lancaster University (LU). The primary aim of the project is to use numerical simulation to optimize the collector geometry for power production over a range of likely wave climates. A secondary aim is to evaluate the ability of commercial codes to simulate rigid body motion in linear and non-linear wave climates in order to choose the optimal code with respect to compute speed and ease of problem setup. Issues relating to the ability of a code in terms of numerical dissipation of waves, wave absorption, wave breaking, grid generation and moving bodies will all be discussed. The findings of this paper serve as a basis for an informed choice of commercial package for such simulations. However the capability of these commercial codes is increasing with every new release.

Design and Potential Application of Small Scale Wave Energy Converter

2017 ◽  
Author(s):  
Tunde O. Aderinto ◽  
Francisco Haces-Fernandez ◽  
Hua Li
Keyword(s):  
Wave Energy ◽  
Energy Production ◽  
Energy Resource ◽  
Appropriate Technology ◽  
Wave Energy Converter ◽  
Small Scale ◽  
Ocean Energy ◽  
Energy Converter ◽  
Wave Energy Converters ◽  
Wave Properties

Although theoretical available wave energy is higher than most of ocean energy sources, the commercial utilization of wave energy is much slower than other ocean energy sources. The difficulty of integration with the electrical grid system and the challenges of the installation, operation and maintenance of large energy generation and transmission systems are the major reasons. Even though there are successfully tested models of wave energy converters, the fact that wave energy is directly affected by wave height and wave period makes the actual wave energy output with high variation and difficult to be predicted. And most of the previous studies on wave energy and its utilization have focused on the large scale energy production that can be integrated into a power grid system. In this paper, the authors identify and discuss stand-alone wave energy converter systems and facilities that are not connected to the electricity grid with focus on small scale wave energy systems as potential source of energy. For the proper identification, qualification and quantification of wave energy resource potential, wave properties such as wave height and period need to be characterized. This is used to properly determine and predict the probability of the occurrence of these wave properties at particular locations, which enables the choice of product design, installation, operation and maintenance to effectively capture wave energy. Meanwhile, the present technologies available for wave energy converters can be limited by location (offshore, nearshore or shoreline). Therefore, the potential applications of small scale stand-alone wave energy converter are influenced by the demand, location of the need and the appropriate technology to meet the identified needs. The paper discusses the identification of wave energy resource potentials, the location and appropriate technology suitable for small scale wave energy converter. Two simplified wave energy converter designs are created and simulated under real wave condition in order to estimate the energy production of each design.

scholarly journals Using Flexible Blades to Improve the Performance of Novel Small-Scale Counter-Rotating Self-Adaptable Wave Energy Converter for Unmanned Marine Equipment

2019 ◽  
Vol 7 (7) ◽  
pp. 223 ◽  
Author(s):  
Sun ◽  
Shang ◽  
Luo ◽  
Lu ◽  
Wu ◽  
...  
Keyword(s):  
Output Power ◽  
Wave Energy ◽  
Power Supply ◽  
Simulation Analysis ◽  
Average Power ◽  
Wave Energy Converter ◽  
Small Scale ◽  
Energy Converter ◽  
Experimental Conditions ◽  
Blade Thickness

Unmanned marine equipment has been increasingly developed for open seas. The lack of efficient and reliable power supply is currently one of the bottlenecks restricting the practical application of these devices. In order to provide a viable power supply method for unmanned marine equipment, such as sonic buoys and sea robots, we originally propose a novel small-scale flexible blade wave energy converter (WEC) based on self-adaptable counter-rotating operation mechanism. The flexible blade WEC is designed on the basis of the rigid blade WEC with the caging device. This paper identifies the key factors affecting WEC performance through theoretical analysis. According to the numerical simulation analysis, the output mechanical power of the double-layer absorber is 12.8 W, and the hydraulic efficiency is 36.3%. The results of the verification experiment show that the peak power of WEC is 5.8 W and the average power is 3.2 W. The WEC with 65Mn flexible blade under most experimental conditions has the best performance when the blade thickness is 0.10 mm. The study shows that the new generation WEC can effectively overcome the excessive fluctuation of the output power of the previous generation WEC. The output power curve of the novel WEC is relatively smooth, which is conducive to its smooth operation and subsequent utilization and storage of electrical energy.

Comparison of Mooring Loads in Survivability Mode on the Wave Dragon Wave Energy Converter Obtained by a Numerical Model and Experimental Data

2012 ◽  
Author(s):  
Stefano Parmeggiani ◽  
Made Jaya Muliawan ◽  
Zhen Gao ◽  
Torgeir Moan ◽  
Erik Friis-Madsen
Keyword(s):  
Numerical Model ◽  
Wave Energy ◽  
Complex Geometry ◽  
Wave Energy Converter ◽  
Scale Model ◽  
Coupled Analysis ◽  
Small Scale ◽  
Energy Converter ◽  
Numerical Predictions ◽  
Small Scale Model

The Wave Dragon Wave Energy Converter is ready to be up-scaled to commercial size. The design and feasibility analysis of a 1.5 MW pre-commercial unit to be deployed at the DanWEC test center in Hanstholm, Denmark, is currently ongoing. With regard to the mooring system, the design has to be carried out numerically, through coupled analyses of alternative solutions. The present study deals with the preliminary hydrodynamic characterization of Wave Dragon needed in order to calibrate the numerical model to be used for the mooring design. A hydrodynamic analysis of the small scale model in the frequency domain is performed by the software HydroD, which uses WAMIT as core software. The quadratic damping term, accounting for the viscous effect, is determined through an iterative procedure aimed at matching numerical predictions on the mooring tension, derived through time domain coupled analysis, with experimental results derived from tank tests of a small scale model. Due to the complex geometry of the device, a sensitivity analysis is performed to discuss the influence of the mean position on the quality of the numerical predictions. Good correspondence is achieved between the experimental and numerical model. The numerical model is hence considered reliable for future design applications.

scholarly journals Numerical Study on the Optimization of Hydrodynamic Performance of Oscillating Buoy Wave Energy Converter

2021 ◽  
Vol 28 (1) ◽  
pp. 48-58
Author(s):  
Wenbin Lai ◽  
Yonghe Xie ◽  
Detang Li
Keyword(s):  
Wave Energy ◽  
Numerical Study ◽  
Energy Conversion Efficiency ◽  
Absorption Efficiency ◽  
Wave Energy Converter ◽  
Hydrodynamic Performance ◽  
Energy Converter ◽  
Physical Experiments ◽  
Working Principle ◽  
The Waves

Abstract The oscillating buoy wave energy converter (OBWEC) captures wave energy through the undulating movement of the buoy in the waves. In the process of capturing wave energy, the hydrodynamic performance of the buoy plays an important role. This paper designed the “Haida No. 1” OBWEC, in which the buoy adopts a form of swinging motion. In order to further improve the hydrodynamic performance of the buoy, a 2D numerical wave tank (NWT) model is established using ADINA software based on the working principle of the device. According to the motion equation of the buoy in the waves, the influence of the buoy shape, arm length, tilt angle, buoy draft, buoy width, wave height and Power Take-off (PTO) damping on the hydrodynamic performance of the buoy is studied. Finally, a series of physical experiments are performed on the device in a laboratory pool. The experimental results verify the consistency of the numerical results. The research results indicate that the energy conversion efficiency of the device can be improved by optimizing the hydrodynamic performance of the buoy. However, the absorption efficiency of a single buoy for wave energy is limited, so it is very difficult to achieve full absorption of wave energy.

Sign in / Sign up

Export Citation Format

Share Document