On fineness of grain

2011 ◽  
Vol 163 (3) ◽  
pp. 763-781 ◽  
Author(s):  
Jeffrey C. King
Keyword(s):  
1977 ◽  
Vol 57 (1) ◽  
pp. 1-8
Author(s):  
A. R. MACK ◽  
E. J. BRACH

Samples of granular materials illuminated with a 20 m Watt (average power) laser energy source at a wavelength of 337.1 nm differed in their fluorescence spectra over a wide range of wavelengths from approximately 380 to 660 nm. The fluorescent yield was usually higher with increased fineness of grain size and with increased concentration of clay (> 10% of under 2-μ grain size). However, sandy soils containing a low content of clay (i.e. < 10%) had a higher yield than the regression estimate. Modifying the fluorosensor for greater resolution at a higher energy level (1 nm bandwidth and 25 m Watt average power) resulted in eight discernible peaks between 384 and 440 nm, at 486 and at 550 nm. Overall fluorescence was markedly increased by removal of Fe coatings from the surface of the grains by a dithionite treatment. Thus, laser-induced fluorescence spectra obtained from various partially vegetated land areas by airborne laser fluorosensing may be influenced by the granular material associated with non-vegetated "open" areas.


1904 ◽  
Vol 1 (8) ◽  
pp. 418-422 ◽  
Author(s):  
A. K. Coomáraswámy

The name ‘Balangoda group’ is proposed for a series of granitic and pegmatite-like rocks, intrusive in, but distinct from, the Charnockite series; first met with in the Balangoda district, but evidently widely distributed over a large area between Balangoda and Hatton. The rocks are best described as granites, but occur most often in rather narrow dykes, after the manner of pegmatites. Yet there is no reason for separating the smaller from the larger masses, and the term granite is applied to both. The group (of which a more detailed account will ultimately be needed) includes in particular zircon granite, allanite granite, magnetite granite, and granite without conspicuous accessory minerals; as well as the probably similar rocks in which the hitherto unlocated minerals geikielite, baddeleyite, rutile, fergusonite, thorite, thorianite, etc., may be looked for; and the vein of pegmatite at Gampola, which consisted of quartz, felspars, and biotite, with apatite, ilmenite, tourmaline, and the new mineral described as thorianite as accessory minerals.These granites are intrusive in the Charnockite series, and though frequently occurring in lenticular masses (Denagama) with a disposition parallel to that of the foliation planes of the charnockites, have often been observed to transgress these foliation planes and to behave as intrusive rocks. Contact phenomena have not, however, been observed, except perhaps in a slight tendency to a peripheral fineness of grain in the intrusive rocks. At the junctions granite and charnockite are usually welded together, there being no absolutely hard line of separation, although the junction may be called sharp; in the case of the larger masses no good junctions have been seen.


2018 ◽  
pp. 26-28
Author(s):  
A. R. Ashiev ◽  
М. V. Skulova ◽  
K. N. Khabibullin

The studies were carried out in 2016–2018 in the competitive variety testing of peas on the crop rotation fields belonging to the laboratory of legume breeding and seed-growing of the FSBSI “Agricultural Research Center “Donskoy”, located in the part of the Rostov region with unstable humidity (Zernograd). During the years of research, the meteorological conditions of the pea vegetation were contrast that made it possible to objectively estimate the pea lines in the given weather and climate conditions. In the com­petitive variety testing, the 18 lines were studied according to economically valuable traits (seed productivity, productivity elements, adaptability to machine harvesting). As a result of the study, the 6 pea lines were identified: 2 lines of the mustache morphotype “G-1002”, “G-1003”; 4 leafy lines “G-1010”, “G-1011”, “G-1013” and “G-1015”. In the group of the mustache morphotype, 2 lines “G-1002” (on 0.30 t/ha), “G-1003” (on 0.39 t/ha) exceeded the grain productivity of the standard variety for 3 years of study on aver­age. The productivity increase was from 12.4 to 16.1%. In the group of variety samples of the leafy morphotype, the line “G-1010” (on 0.31 t/ha) significantly exceeded grain productivity of the standard variety. All the selected lines were tolerant to their seed-shedding. The line “G-1010” (48.8 pc per plant) showed the highest seed yield per plant. The lines “G-1003” (222.1 g), “G-1011” (209.5 g) and “G-1013” (207.8 g) had the largest fineness of grain. The line “G-1010” (8.85 g/plant) demonstrated the highest productivity per plant. However, having a low coefficient of resistance to lodging (0.35), this line has the greatest loss of seeds during harvesting. The iden­tified lines will be used in further breeding work according to a number of their economically valuable traits.


Ratio ◽  
2011 ◽  
Vol 24 (3) ◽  
pp. 243-258 ◽  
Author(s):  
Kevin Connolly
Keyword(s):  

Dialogue ◽  
2008 ◽  
Vol 47 (3-4) ◽  
pp. 677-686
Author(s):  
Andre J. Abath
Keyword(s):  

2017 ◽  
Vol 750 ◽  
pp. 20-25
Author(s):  
Florina Violeta Anghelina ◽  
Ionica Ionita ◽  
Dan Nicolae Ungureanu ◽  
Elena Valentina Stoian ◽  
Ileana Nicoleta Popescu ◽  
...  

This paper presents experimental results revealed on the samples type 2024 aluminum alloy used in aeronautics. Adequate characterization of 2024 aluminum alloys with special destination (aviation) was achieved by combined investigations:(i) wet chemical analysis, (ii) spectrochemical analysis, (iii) X-ray diffraction and (iv) electron microscopy. The main conclusion that emerges from the investigations carried out on aluminum samples revealed that: (a) alloys fits in terms of composition with the standard specification for 2024, in all cases; (b) microstructure vary in fineness of grain, but meets the requirements of aviation rules; the investigated microstructures have been appreciated as adequate of aluminum alloys type "2024".


Sign in / Sign up

Export Citation Format

Share Document