Compressive strength and stability of sustainable self-consolidating concrete containing fly ash, silica fume, and GGBS

2017 ◽  
Vol 11 (4) ◽  
pp. 406-411 ◽  
Author(s):  
Osama Ahmed Mohamed ◽  
Omar Fawwaz Najm
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Self Consolidating Concrete

Durability of Sustainable Self-Consolidating Concrete

2018 ◽  
Vol 765 ◽  
pp. 285-289
Author(s):  
Osama Ahmed Mohamed ◽  
Waddah Al Hawat ◽  
Omar Fawwaz Najm
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cementitious Materials ◽  
Chloride Penetration ◽  
Supplementary Cementitious Materials ◽  
Test Results ◽  
Self Consolidating Concrete ◽  
Human Footprint ◽  
Granulated Blast Furnace Slag

Supplementary cementitious materials such as fly ash, silica fume and ground granulated blast furnace slag (GGBS) have been used widely to partially replace cement in producing self-consolidating concrete (SCC). The production of cement is associated with emission of significant amounts of CO2 and increases the human footprint on the environment. Fly ash, silica fume, and GGBS are recycled industrial by-products that also impart favorable fresh and hardened properties on concrete. This study aims to assess the effect of the amounts of fly ash and silica fume on strength and chloride penetration resistance of concrete. Rapid Chloride Penetration Test (RCPT) was used to assess the ability of SCC to resist ingress of chlorides into concrete. SCC mixes with different dosages of fly ash and silica fume were developed and tested at different curing ages. Test results showed that replacing 20% of cement with fly ash produced the highest compressive strength of 67.96 MPa among all fly ash-cement binary mixes. Results also showed that replacing15% of cement with silica fume produced the highest compressive strength of 95.3 MPa among fly ash-cement binary mixes. Using fly ash and silica fume consistently increased the concrete resistance to chloride penetration at the early ages. Silica fume at all dosages results in low or very low levels of chloride penetration at all curing ages of concrete.

scholarly journals Durability and Compressive Strength of High Cement Replacement Ratio Self-Consolidating Concrete

Buildings ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 153 ◽  
Author(s):  
Osama Mohamed
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Structural Engineering ◽  
Chloride Ion ◽  
Strength Development ◽  
Replacement Ratio ◽  
Self Consolidating Concrete ◽  
Granulated Blast Furnace Slag ◽  
Chloride Penetration Resistance

This study examines durability and mechanical properties of sustainable self-consolidating concrete (SCC) in which 80% of the cement is replaced with combinations of recycled industrial by-products including fly ash, silica fume, and ground granulated blast furnace slag (GGBS). The water to binder (w/b) ratio of SCC mixes studies was maintained at 0.36. The study proposes empirical relationships to predict 28-day compressive strengths based on the results of three-day and seven-day compressive strengths. In addition, the chloride penetration resistance of the various sustainable SCC mixes was determined after three days, seven days, and 28 days of moist curing of concrete standards. It was concluded that fly ash, silica fume, and GGBS contribute favorably to enhancing strength development, fresh properties, and durability of SCC in comparison to ordinary Portland cement (OPC). The compressive strength of the sustainable SCC mixes falls within ranges suitable for structural engineering applications. Replacing cement with 15% silica fume produced a 28-day average compressive strength of 95.3 MPa, which is 44.2% higher than the control mix. Replacing cement with 15% or 20% silica fume reduced the chloride ion permeability to very low amounts compared to high permeability in a control mix.

scholarly journals Effect of Mix Constituents and Curing Conditions on Compressive Strength of Sustainable Self-Consolidating Concrete

2019 ◽  
Vol 11 (7) ◽  
pp. 2094 ◽  
Author(s):  
Osama Ahmed Mohamed
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Stability Index ◽  
Strength Development ◽  
Self Consolidating Concrete ◽  
Curing Conditions ◽  
Practical Applications ◽  
Water Curing ◽  
Curing Method

The production of cement requires significant energy and is responsible for more than 5% of global CO2 emissions; therefore it is imperative to reduce the production and use of ordinary portland cement (OPC). This paper examines the compressive strength development of low water-to-binder (w/b) ratio self-consolidating concrete (SCC) in which 90% of the cement is replaced with industrial by-products including ground granulated blast furnace slag (GGBS), fly ash, and silica fume. The emphasis in this paper is on replacing a large volume of cement with GGBS, which represented 10% to 77.5% of the cement replaced. Fresh properties at w/b ratio of 0.27 were examined by estimating the visual stability index (VSI) and t50 time. The compressive strength was determined after 3, 7, 28, and 56 days of curing. The control mix made with 100% OPC developed compressive strength ranging from 55 MPa after three days of curing to 76.75 MPa after 56 days of curing. On average, sustainable SCC containing 10% OPC developed strength ranging from 31 MPa after three days of curing to 56.4 MPa after 56 days of curing. However, the relative percentages of fly ash, silica fume, and GGBS in the 90% binder affect the strength developed as well. In addition, this paper reports the effect of the curing method on the 28 day compressive strength of environmentally friendly SCC in which 90% of the cement is replaced by GGBS, silica fume, and fly ash. The highest compressive strength was achieved in samples that were cured for three days under water, then left to air-dry for 25 days, compared to samples cured using chemical compounds or samples continuously cured under water for 28 days. The study confirms that SCC with 10% OPC and 90% supplementary cementitious composites (GGBS, silica fume, fly ash) can achieve compressive strength sufficient for many practical applications by incorporating high amounts of GGBS. In addition, air-curing of samples in a relatively high temperature (after three days of water curing) produce a higher 28 day compressive strength compared to water curing for 28 days, or membrane curing.

COMPRESSIVE STRENGTH AND THERMAL CONDUCTIVITY OF WATER AND AIR CURED PORTLAND CEMENT-FLY ASH-SILICA FUME MORTARS

2018 ◽  
Vol 17 (9) ◽  
pp. 2023-2030
Author(s):  
Arnon Chaipanich ◽  
Chalermphan Narattha ◽  
Watcharapong Wongkeo ◽  
Pailyn Thongsanitgarn
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Fly Ash ◽  
Portland Cement ◽  
Silica Fume

Optimization of Concrete Porous Mix Using Slag as Substitute Material for Cement and Aggregates

2017 ◽  
Vol 865 ◽  
pp. 282-288 ◽  
Author(s):  
Jul Endawati ◽  
Rochaeti ◽  
R. Utami
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
Environmental Effect ◽  
Substitution Effect ◽  
Main Concern ◽  
Binder Material ◽  
Furnace Slag

In recent years, sustainability and environmental effect of concrete became the main concern. Substituting cement with the other cementitious material without decreasing mechanical properties of a mixture could save energy, reduce greenhouse effect due to mining, calcination and limestone refining. Therefore, some industrial by-products such as fly ash, silica fume, and Ground Iron Blast Furnace Slag (GIBFS) would be used in this study to substitute cement and aggregate. This substitution would be applied on the porous concrete mixture to minimize the environmental effect. Slag performance will be optimized by trying out variations of fly ash, silica fume, and slag as cement substitution material in mortar mixture. The result is narrowed into two types of substitution. First, reviewed from the fly ash substitution effect on binder material, highest compressive strength 16.2 MPa was obtained from mixture composition 6% fly ash, 3% silica fume and 17% grinding granular blast-furnace slag. Second, reviewed from slag types as cement substitution and silica fume substitution, highest compressive strength 15.2 MPa was obtained from mortar specimens with air-cooled blast furnace slag. It composed with binder material 56% Portland composite cement, 15% fly ash, 3% silica fume and 26% air-cooled blast furnace slag. Considering the cement substitution, the latter mixture was chosen.

scholarly journals Research on Mechanical Performance & Behaviour of Geopolymer Concrete Subjected to Elevated Temperatures

2019 ◽  
Vol 8 (2S8) ◽  
pp. 883-887
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Geopolymer Concrete ◽  
Sem Images ◽  
Before And After ◽  
Alkaline Conditions ◽  
Compressive Strength Of Concrete

The investigative studies on mechanical performance & behaviour, of Geopolymer Concrete (GPC) before and after the exposure to elevated temperatures (of 200 0 C -1000 0 C with an increment of 100 0 C). Indicate that the GPC Specimens Exhibited better Compressive strength at higher temperatures than that of those made by regular OPC Concrete with M30 Grade. The chronological changes in the geopolymeric structure upon exposure to these temperatures and their reflections on the thermal behaviour have also been explored. The SEM images indicate GPC produced by fly ash , metakaolin and silica fume, under alkaline conditions form Mineral binders that are not only non-flammable and but are also non-combustible resins and binders. Further the Observations drawn disclose that the mass and compressive strength of concrete gets reduced with increase in temperatures.

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

Fresh, Durability and Mechanical Behavior of Self Consolidating Concrete Incorporating Fly Ash and Admixture under Hot Weather

2021 ◽  
Vol 904 ◽  
pp. 453-457
Author(s):  
Samer Al Martini ◽  
Reem Sabouni ◽  
Abdel Rahman Magdy El-Sheikh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Weather Conditions ◽  
Chloride Penetration ◽  
The Self ◽  
Fresh Properties ◽  
Self Consolidating Concrete ◽  
Slump Flow ◽  
Hot Weather

The self-consolidating concrete (SCC) become the material of choice by concrete industry due to its superior properties. However, these properties need to be verified under hot weather conditions. The paper investigates the behavior of SCC under hot weather. Six SCC mixtures were prepared under high temperatures. The SCC mixtures incorporated polycarboxylate admixture at different dosages and prolonged mixed for up to 2 hours at 30 °C and 40 °C. The cement paste was replaced with 20% of fly ash (FA). The fresh properties were investigated using slump flow, T50, and VSI tests. The compressive strength was measured at 3, 7, and 28 days. The durability of SCC mixtures was evaluated by conducting rapid chloride penetration and water absorption tests.

Sign in / Sign up

Export Citation Format

Share Document