scholarly journals Ultrasound Assisted Alkaline Pre‐treatment Efficiently Solubilises Hemicellulose from Oat Hulls

2021 ◽  
Author(s):  
Eva Schmitz ◽  
Eva Nordberg Karlsson ◽  
Patrick Adlercreutz
Keyword(s):  
Main Chain ◽  
Waste Product ◽  
Deep Eutectic Solvents ◽  
Treatment Method ◽  
Oat Hulls ◽  
Physical Chemical ◽  
Physico Chemical ◽  
Ultrasound Assisted ◽  
Pre Treatment ◽  
Optimized Conditions

AbstractThe establishment of sustainable bioeconomies requires the utilization of new renewable biomaterials. One such material currently seen as a waste product is oat hulls. Oat hulls exhibit a great potential for the production of dietary fibres due to their exceptionally large hemicellulose content (35%). Their recalcitrant structure however requires a suitable pre-treatment method to access and process the hemicellulose. After a screening of various physical, chemical and physico-chemical pre-treatment methods, including autoclaving, ultrasonication, microwave-, deep eutectic solvents-, as well as alkaline treatments, a combined ultrasonication and alkali pre-treatment method was here found to be the most suitable. A factorial design resulted in optimized conditions of 10 min ultrasonication in water, followed by an incubation in 5 M NaOH at 80 ºC for 9 h yielding solubilisation of 72% of all hemicellulose in the hulls. The method was shown to efficiently break the ester bonds between ferulic acid and the hemicellulose main chain, contributing to its solubilisation. Graphic Abstract

scholarly journals Compost leachate treatment using polyaluminium chloride and nanofiltration

2017 ◽  
Vol 15 (1) ◽  
pp. 123-128 ◽  
Author(s):  
Marjana Simonič
Keyword(s):  
Zeta Potential ◽  
Isoelectric Point ◽  
Oxygen Demand ◽  
Treatment Method ◽  
Aluminium Chloride ◽  
Leachate Treatment ◽  
Physico Chemical ◽  
Pre Treatment ◽  
Ph Range ◽  
Compost Leachate

AbstractLaboratory scale filtration tests utilizing leachate were conducted to investigate fouling and filtration performance of nanofiltration membranes. The work presented in this study is conducted on real samples rather than model water. Physico-chemical analyses showed that the leachate contained a lot of organic substances, exceeding 20000 mg/L O2 expressed as chemical oxygen demand. Proper pre-treatment method must be chosen in order to reduce fouling index. Coagulation pre-treatment using poly-aluminium chloride was chosen. Two thin film polysulfone membranes were used, purchased by Osmonic Desal. The focus of this research is to assess the influence of the particle size and zeta-potential of the colloidal fraction in leachate on nanofiltration performance. The isoelectric point of both membranes was 4.7 and 4.3, respectively. The fouled membranes were negatively charged over the pH range with isoelectric point shifting to the left (lower pH) indicating the foulant material mainly not charged. It was confirmed by its zeta-potential, measured at -2 mV.

EELS characterization of “Smut” layer films on steel surface prepared for chrome plating by anodic etching

1995 ◽  
Vol 53 ◽  
pp. 538-539
Author(s):  
E Y. Wang ◽  
J. T. Cherian ◽  
A. Madsen ◽  
R. M. Fisher
Keyword(s):  
Steel Surface ◽  
Surface Preparation ◽  
Treatment Method ◽  
Chrome Plating ◽  
Transmission Electron ◽  
Alloy Steels ◽  
Pre Treatment ◽  
Hard Chrome ◽  
Electron Energy Loss

Many steel parts are electro-plated with chromium to protect them against corrosion and to improve their wear-resistance. Good adhesion of the chrome plate to the steel surface, which is essential for long term durability of the part, is extremely dependent on surface preparation prior to plating. Recently, McDonnell Douglas developed a new pre-treatment method for chrome plating in which the steel is anodically etched in a sulfuric acid and hydrofluoric acid solution. On carbon steel surfaces, this anodic pre-treatment produces a dark, loosely adhering material that is commonly called the “smut” layer. On stainless steels and nickel alloys, the surface is only darkened by the anodic pre-treatment and little residue is produced. Anodic pre-treatment prior to hard chrome plating results in much better adherence to both carbon and alloy steels.We have characterized the anodic pre-treated steel surface and the resulting “smut” layer using various techniques including electron spectroscopy for chemical analysis (ESCA) on bulk samples and transmission electron microscopy (TEM) and electron energy-loss spectroscopy (EELS) on stripped films.

Enzyme-assisted Extraction for Optimized Recovery of Phenolic Bioactives from Peganum hermala Leaves Using Response Surface Methodology

2018 ◽  
Vol 17 (4) ◽  
pp. 349-354
Author(s):  
Qadir Rahman ◽  
Anwar Farooq ◽  
Amjad Gilani Mazhar ◽  
Nadeem Yaqoob Muhammad ◽  
Ahmad Mukhtar
Keyword(s):  
Response Surface Methodology ◽  
Response Surface ◽  
Enzyme Concentration ◽  
Coumaric Acid ◽  
Assisted Extraction ◽  
Pre Treatment ◽  
Optimized Conditions ◽  
Enzyme Complexes ◽  
Hydrolysis Of ◽  
Central Composite

This study investigates the effect of enzyme formulations (Zympex-014, Kemzyme dry-plus and Natuzyme) on recovery of phenolics from Peganum hermala (harmal) leaves, under optimized conditions using response surface methodology. As compared to the other enzyme complexes, the yield (34 g/100g) obtained through Zympex-014-assisted extraction was higher under optimized conditions such as time (75 min), temperature (70°C), pH (6.5) and enzyme concentration (5 g/100 g) using central composite design (CCD). Effectiveness of Zympex-014 towards hydrolysis of P. hermala leaves cell wall was examined by analyzing the control and enzyme-treated leave residues using scanning electron microscope (SEM). GC/MS characterization authenticated the presence of quercetin (1.44), gallic acid (0.23), caffeic acid (0.04), cinnamic acid (0.05), m-coumaric acid (0.23) and p-coumaric acid (0.37 μg/g) as the potent phenolics in Zympex-014 based extract. It can be concluded from the findings of the current work that pre-treatment of P. hermala leaves with Zympex-014 significantly enhanced the recovery of phenolics that supports its potential uses in the nutra-pharamaceutical industry.

scholarly journals The effect of drying temperature on the properties of gelatin from carps (Cyprinus carpio) skin

2019 ◽  
Vol 37 (No. 4) ◽  
pp. 246-251 ◽  
Author(s):  
Joanna Tkaczewska ◽  
Maciej Wielgosz ◽  
Piotr Kulawik ◽  
Marzena Zajac
Keyword(s):  
Cyprinus Carpio ◽  
Freeze Drying ◽  
Treatment Method ◽  
Thermal Hydrolysis ◽  
Gel Properties ◽  
Drying Temperature ◽  
Freeze Dried ◽  
Different Temperatures ◽  
Pre Treatment ◽  
Hydrolysis Of

The influence of drying temperature on the characteristics and gel properties of gelatine from Cyprinus carpio L. skin was studied. Gelatine was extracted from the carp skin using NaOH and ethanol pre-treatment method, extracted in water in 45°C and then dried in 4 different temperatures: 50, 70, 80°C and freeze-dried. The  electrophoresis and functional properties of gelatines were investigated. Freeze drying allowed to obtain a high gelling force, and all other methods did not give satisfactory results. The proteins in gelatines dried at higher temperatures separated by electrophoresis gave severely blurred bands. It may be explained by thermal hydrolysis of collagen fibrils. Freeze drying is the only effective method for drying this product, which can be used in industry.

Development of an MSFIA-MPFS pre-treatment method for radium determination in water samples

Talanta ◽  
2007 ◽  
Vol 71 (3) ◽  
pp. 1172-1179 ◽  
Author(s):  
Y. Fajardo ◽  
E. Gómez ◽  
F. Garcias ◽  
V. Cerdà ◽  
M. Casas
Keyword(s):  
Water Samples ◽  
Treatment Method ◽  
Pre Treatment

scholarly journals Novel pre-treatment method for seawater reverse osmosis: Fibre media filtration

Desalination ◽  
2010 ◽  
Vol 250 (2) ◽  
pp. 557-561 ◽  
Author(s):  
J.J. Lee ◽  
M.A.H. Johir ◽  
K.H. Chinu ◽  
H.K. Shon ◽  
S. Vigneswaran ◽  
...  
Keyword(s):  
Reverse Osmosis ◽  
Treatment Method ◽  
Seawater Reverse Osmosis ◽  
Pre Treatment

Research on Detecting Tris-(2,3-dibromopropyl)-Phosphate in Textiles with the HPLC/DAD Method

2012 ◽  
Vol 441 ◽  
pp. 640-644
Author(s):  
Ke Jie Fu ◽  
Li Sheng Yang ◽  
Chang Sheng Feng ◽  
Liang Chen
Keyword(s):  
Limit Of Detection ◽  
Extraction Process ◽  
Ultrasound Assisted Extraction ◽  
Routine Testing ◽  
Assisted Extraction ◽  
Ultrasound Assisted ◽  
Pre Treatment ◽  
Finishing Agent ◽  
Detecting Method ◽  
Precision Test

A detecting method for toxic flame retardant finishing agent tris-(2,3-dibromopropyl) -phosphate (TRIS for short) in textiles was studied. In the method, an acetonitrile ultrasound-assisted extraction process was included in sample pre-treatment, and HPLC/DAD was used in the separation and identification of extractives. After that, the conditions of pre-treatment and chromatograph were optimized. The results showed that the limit of detection (LOD) by this method (S/N10) is 1.0 mg/kg, its recovery ranged from 78.1% to 98.4%, and RSD of the precision test is 3.2%, of which all met the requirements for routine testing.

Fabrication and characterization of composite MoS2-TiO2 coating material

2021 ◽  
pp. 095440622110157
Author(s):  
Avinash V Borgaonkar ◽  
Ismail Syed ◽  
Shirish H Sonawane
Keyword(s):  
Bond Strength ◽  
Treatment Method ◽  
Optical Microscope ◽  
Scratch Resistance ◽  
Substrate Material ◽  
Coating Film ◽  
Tribological Behaviour ◽  
Molybdenum Disulphide ◽  
Before And After ◽  
Pre Treatment

Molybdenum disulphide (MoS2) is a popularly used solid lubricant in various applications due to its superior tribological behaviour. However, it possesses poor wear resistance which requires further improvement. In the present study efforts have been made to enhance the tribological properties of pure MoS2 coating film by doping TiO2 nanoparticles as a reinforcement material. The Manganese phosphating is selected as a pre-treatment method to improve the bond strength between coating and substrate. The coating is bonded with the substrate material employing sodium silicate as a binder. The effects of wt. % of TiO2 onto the mechanical properties of composite MoS2-TiO2 coating such as hardness and bond strength have been studied. In addition coating microstructure before and after experimental test was studied using optical microscope and scanning electron microscope. It was also found that with increase in wt. % addition of TiO2 upto 15% into MoS2 base matrix, the hardness of coating increases proportionally. Beyond 15 wt. % addition of TiO2, the coating becomes brittle in nature. This leads to reduction in the scratch resistance.

Sign in / Sign up

Export Citation Format

Share Document