scholarly journals Force feedback-based quality monitoring of the friction stir welding process utilizing an analytic algorithm

2020 ◽  
Author(s):  
P. Rabe ◽  
A. Schiebahn ◽  
U. Reisgen
Keyword(s):  
Friction Stir Welding ◽  
Monitoring System ◽  
Force Feedback ◽  
Weld Seam ◽  
Position Control ◽  
Welding Process ◽  
Quality Monitoring ◽  
Welding Parameters ◽  
Process Data ◽  
Friction Stir

AbstractThe friction stir welding (FSW) process is known as a solid-state welding process, comparatively stable against external influences. Therefore, the process is commonly used with fixed welding parameters, utilizing axial force control or position control strategies. External and internal process disturbances introduced by workpiece, gap tolerance, tool wear, or machine/tool inadequacies are rarely monitored, and conclusions about the weld seam quality, based on the recorded process data, are not drawn. This paper describes an advancement, improving on research into the correlation of process force feedback events or gradual force changes and the resulting weld seam characteristics. Analyzing the correlation between examined weld sections and high-resolution rate force data, a quality monitoring system based on an analytic algorithm is described. The monitoring system is able to accurately distinguish sound welds from such with internal (void) and external (flash) defects.

Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

Process Parameter Optimization of Friction Crush Welding (FCW) of AISI 304 Stainless Steel

2017 ◽  
Author(s):  
Gurinder Singh Brar ◽  
Manpreet Singh ◽  
Ajay Singh Jamwal
Keyword(s):  
Stainless Steel ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Pressure Vessels ◽  
304 Stainless Steel ◽  
Welding Parameters ◽  
Work Piece ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304 ◽  
Friction Stir

AISI 304 stainless steel is one of the grades of steel widely used in engineering applications particularly in chemical equipments, food processing, pressure vessels and paper industry. Friction crush welding (FCW) is type of friction welding, where there is a relative motion between the tool and work-piece. In FCW process, the edges of the work-piece to be joined are prepared with flanged edges and then placed against each other. A non-consumable friction disc tool will transverse with a constant feed rate along the edges of the work-piece, which leads to welding. The joint is formed by the action of crushing a certain amount of additional flanged material into the gap formed by the contacting material. The novelty of present work is that FCW removes the limitations of friction stir welding and Steel work pieces can be economically welded by FCW. Taguchi method of Design of Experiments (DOE) is used to find optimal process parameters of Friction Crush Welding (FCW). A L9 Orthogonal Array, Signal to Noise ratio (S/N) and Analysis of Variance are applied to analyze the effect of welding parameters (welding speed, RPM, tool profile) on the weld properties like bond strength. Grain refinement takes place in friction crush welding as is seen in friction stir welding. Friction crush welding process also has added advantage in reducing distortion and residual stresses.

Heat Transfer Simulations and Analysis of Joint Cross-Sectional Microstructure on Friction Stir Welding between Steel and Aluminium

2020 ◽  
Vol 863 ◽  
pp. 85-95
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tu Vinh Thong ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Thermal Contact ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Sem Images ◽  
Cross Sectional ◽  
Friction Stir

This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between Aluminium and steel, and (3) The welding process using stiring friction is simulated. The simulations intended to predicting the temperature which is used for preheat and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength is carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed and offset), temperature and tensile strength. The maximum tensile strength is 77% compared to the strength of aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving good quality of welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

Influence of Tool Rotational Speed on the Mechanical Properties of Friction Stir Welded Al-Cu-Li Alloy

2016 ◽  
Vol 857 ◽  
pp. 228-231
Author(s):  
Ho Sung Lee ◽  
Ye Rim Lee ◽  
Kyung Ju Min
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Space Shuttle ◽  
Welding Process ◽  
High Strength ◽  
Fusion Welding ◽  
Welding Parameters ◽  
Friction Stir ◽  
Mechanical And Microstructural Properties ◽  
Tool Rotation

Aluminum-Lithium alloys have been found to exhibit superior mechanical properties as compared to the conventional aerospace aluminum alloys in terms of high strength, high modulus, low density, good corrosion resistance and fracture toughness at cryogenic temperatures. Even though they do not form low-melting eutectics during fusion welding, there are still problems like porosity, solidification cracking, and loss of lithium. This is why solid state friction stir welding is important in this alloy. It is known that using Al-Cu-Li alloy and friction stir welding to super lightweight external tank for space shuttle, significant weight reduction has been achieved. The objective of this paper is to investigate the effect of friction stir tool rotation speed on mechanical and microstructural properties of Al-Cu-Li alloy. The plates were joined with friction stir welding process using different tool rotation speeds (300-800 rpm) and welding speeds (120-420 mm/min), which are the two prime welding parameters in this process.

scholarly journals A Multi-attribute Control Chart for Monitoring Friction Stir Welding Process Considering Small Sample Sizes

2018 ◽  
Vol 23 (4) ◽  
pp. 474-484
Author(s):  
Esmeralda Ramírez-Méndez ◽  
Mario Cantu-Sifuentes ◽  
David Salvador González-González ◽  
Argelia Fabiola Miranda-Pérez ◽  
Rolando Javier Praga-Alejo
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Control Chart ◽  
Welding Process ◽  
Small Sample ◽  
Sample Sizes ◽  
Process Data ◽  
Friction Stir ◽  
Small Sample Sizes ◽  
Welding Processes

Abstract Often, welding processes used in the industry affect the mechanical properties of materials and quality of a manufactured product. There is, however, an alternative process named Friction Stir Welding (FSW), which is an solid state welding process developed to weld light alloys without compromising their mechanical properties. It is of interest to monitor the performance of FSW process to detect loss of quality. In practice, superficial and internal defects can be found; they can be identified through simple visual inspection and through visual recognition on destructive testing respectively, both procedures represent inspection by attributes. Therefore a multi-attribute control chart is assessed to monitor the process. Commonly, multi-attribute control charts involve high sampling rates to ensure accurate monitoring. In this paper, a multi-attribute control chart is proposed, considering the use of empirical control limits, instead of the theoretical ones, in order to improve its accuracy and lessen the small sample sizes effect. The performance of proposed approaches is analyzed by means of Monte Carlo simulation. The results suggest that the performance of the empirical designs is better than the theoretical ones in all tested cases. Finally, the results of monitoring FSW process data are detailed.

Friction Stir Welding of Mg and Al Alloys

2014 ◽  
Vol 875-877 ◽  
pp. 1477-1482
Author(s):  
Tomáš Kupec ◽  
Ivana Hlaváčová ◽  
Milan Turňa
Keyword(s):  
Friction Stir Welding ◽  
Slovak Republic ◽  
Welding Process ◽  
Hardness Measurement ◽  
Fusion Welding ◽  
Welding Parameters ◽  
Power Sources ◽  
Friction Stir ◽  
Alloy Type ◽  
Equipment Type

The work deals with welding of aluminium alloy typeAlMg4,5Mn and magnesium alloy type AZ 31 in solid state by FSW (Friction Stir Welding) process. Experiments were performed in cooperation with VÚZ PI SR (Welding Research Institute Industrial Institute of Slovak Republic) Bratislava, which has available a new installed equipment type FSW LM 060 manufactured in China. Welding parameters and conditions were proposed and approved. Quality of fabricated joints was assessed by optical microscopy, micro hardness measurement and radiographic test - RT. It was supposed that optimisation of welding parameters would allow to fabricate the joints of acceptable quality that might compete to technologies of fusion welding, including welding with concentrated power sources.

Effect of Shoulder Diameter on the Resulting Interfacial Regions of Friction Stir Welds between Aluminium and Copper

2011 ◽  
Vol 299-300 ◽  
pp. 1146-1150
Author(s):  
Esther Titilayo Akinlabi ◽  
Stephen Akinlabi
Keyword(s):  
Friction Stir Welding ◽  
Feed Rate ◽  
Rotational Speed ◽  
Force Feedback ◽  
Welding Process ◽  
Microstructural Characterization ◽  
Stir Zone ◽  
Vertical Force ◽  
Friction Stir ◽  
Shoulder Diameter

This paper reports the effect of shoulder diameter on the resulting interfacial regions of joints between aluminium and copper produced by the friction stir welding process. The welds were produced using three shoulder diameter tools, viz; 15, 18 and 25 mm. This paper focuses on welds produced at a constant rotational speed of 600 rpm and feed rate of 50 mm/min varying the shoulder diameters. Analysis of the force feedback revealed that the advancing force, the downward vertical force and the torque increases as the shoulder diameter increases. Microstructural characterization was conducted on the joint interfaces and it was observed that the widths of the interfacial regions comprising of the Stir Zone and the Thermo – Mechanically Affected Zone (TMAZ) increases as the shoulder size increases.

Experiment and Simulation of Influence of Welding Parameters on Temperature in Friction Stir Welding

2010 ◽  
Vol 44-47 ◽  
pp. 76-80
Author(s):  
Lei Wang ◽  
Jian Jun Zhu
Keyword(s):  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Temperature Distribution ◽  
Welding Process ◽  
Welding Parameters ◽  
Fem Model ◽  
Friction Stir ◽  
Model Of Friction ◽  
Welding Technique ◽  
Good Agreement

Temperature distribution is the foundation to study friction stir welding technique, influence of welding parameters on temperature was studied through experiment measurement on AA2024-T4 aluminum alloy plates. An instantaneous relative linear velocity based heat source was utilized to build the FEM model of friction stir welding process, good agreement was observed between the measured and simulated thermal profiles. FEM model was also utilized to study effect of welding parameters on temperature distribution.

Sign in / Sign up

Export Citation Format

Share Document