Investigation of cutting parameters affecting on tool wear and surface roughness in dry turning of Ti-6Al-4V using CVD and PVD coated tools

2016 ◽  
Vol 39 (6) ◽  
pp. 2085-2093 ◽  
Author(s):  
Yahya Hışman Çelik ◽  
Erol Kilickap ◽  
Musa Güney
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Parameters ◽  
Dry Turning ◽  
Coated Tools

Effect of cutting parameters on tool wear, cutting force and surface roughness in machining of MDN431 alloy using Al and Fe coated tools

2018 ◽  
Vol 6 (1) ◽  
pp. 016401 ◽  
Author(s):  
Pradeep V Badiger ◽  
Vijay Desai ◽  
M R Ramesh ◽  
B K Prajwala ◽  
K Raveendra
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Force ◽  
Cutting Parameters ◽  
Coated Tools

scholarly journals Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1783
Author(s):  
Hamza A. Al-Tameemi ◽  
Thamir Al-Dulaimi ◽  
Michael Oluwatobiloba Awe ◽  
Shubham Sharma ◽  
Danil Yurievich Pimenov ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Cutting Tool ◽  
Good Practice ◽  
Cutting Tools ◽  
Statistical Design ◽  
Cutting Parameters ◽  
Statistical Design Of Experiments ◽  
Hole Quality ◽  
Coated Tools ◽  
Tool Coating

Aluminum alloys are soft and have low melting temperatures; therefore, machining them often results in cut material fusing to the cutting tool due to heat and friction, and thus lowering the hole quality. A good practice is to use coated cutting tools to overcome such issues and maintain good hole quality. Therefore, the current study investigates the effect of cutting parameters (spindle speed and feed rate) and three types of cutting-tool coating (TiN/TiAlN, TiAlN, and TiN) on the surface finish, form, and dimensional tolerances of holes drilled in Al6061-T651 alloy. The study employed statistical design of experiments and ANOVA (analysis of variance) to evaluate the contribution of each of the input parameters on the measured hole-quality outputs (surface-roughness metrics Ra and Rz, hole size, circularity, perpendicularity, and cylindricity). The highest surface roughness occurred when using TiN-coated tools. All holes in this study were oversized regardless of the tool coating or cutting parameters used. TiN tools, which have a lower coating hardness, gave lower hole circularity at the entry and higher cylindricity, while TiN/TiAlN and TiAlN seemed to be more effective in reducing hole particularity when drilling at higher spindle speeds. Finally, optical microscopes revealed that a built-up edge and adhesions were most likely to form on TiN-coated tools due to TiN’s chemical affinity and low oxidation temperature compared to the TiN/TiAlN and TiAlN coatings.

COMPARISON OF PREPARATION METHODS IN TERMS OF TOOL LIFE AND SURFACE ROUGHNESS

2021 ◽  
Vol 2021 (4) ◽  
pp. 4836-4840
Author(s):  
ROBERT STRAKA ◽  
◽  
JOZEF PETERKA ◽  
TOMAS VOPAT ◽  
◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Cutting Parameters ◽  
Turning Process ◽  
Machined Surface ◽  
Preparation Methods ◽  
Machined Surface Roughness ◽  
Cutting Inserts ◽  
Drag Finishing ◽  
Edge Preparation

The article compares two cutting edge preparation methods and their influence on the machined surface roughness of the difficult to cut nickel alloy Inconel 718 and the tool wear of cutting inserts made of cemented carbide. The manufacturing and preparation process of cutting inserts used in the experiment were made by Dormer Pramet. The preparation methods used in the experiment were drag finishing and brushing. Cutting parameters did not change during the whole turning process to maintain the same conditions in each step of the process and were determined based on tests for a semi-finishing operation of the turning process. To obtain durability of 25 to 30 minutes with controlled development of the tool wear the cutting parameters were determined with cooperation with the cutting inserts manufacturer.

Statistical Study and Multi-Response Optimization of Cutting Parameters for Dry Turning Stainless Steel AISI 316L Using Cermet Tool

2020 ◽  
Vol 36 ◽  
pp. 28-46
Author(s):  
Youssef Touggui ◽  
Salim Belhadi ◽  
Salah Eddine Mechraoui ◽  
Mohamed Athmane Yallese ◽  
Mustapha Temmar
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Aisi 316L ◽  
Cutting Power ◽  
Dry Turning ◽  
Optimization Of Cutting Parameters

Stainless steels have gained much attention to be an alternative solution for many manufacturing industries due to their high mechanical properties and corrosion resistance. However, owing to their high ductility, their low thermal conductivity and high tendency to work hardening, these materials are classed as materials difficult to machine. Therefore, the main aim of the study was to examine the effect of cutting parameters such as cutting speed, feed rate and depth of cut on the response parameters including surface roughness (Ra), tangential cutting force (Fz) and cutting power (Pc) during dry turning of AISI 316L using TiCN-TiN PVD cermet tool. As a methodology, the Taguchi L27 orthogonal array parameter design and response surface methodology (RSM)) have been used. Statistical analysis revealed feed rate affected for surface roughness (79.61%) and depth of cut impacted for tangential cutting force and cutting power (62.12% and 35.68%), respectively. According to optimization analysis based on desirability function (DF), cutting speed of 212.837 m/min, 0.08 mm/rev feed rate and 0.1 mm depth of cut were determined to acquire high machined part quality

scholarly journals Prediction of Tool Lifetime and Surface Roughness for Nickel-Based Waspaloy

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Shao-Hsien Chen ◽  
Chung-An Yu
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
High Speed ◽  
Cutting Speed ◽  
High Strength ◽  
Cutting Parameters ◽  
Experimental Results ◽  
Predictive Values ◽  
Actual Surface ◽  
Wide Range

In recent years, most of nickel-based materials have been used in aircraft engines. Nickel-based materials applied in the aerospace industry are used in a wide range of applications because of their strength and rigidity at high temperature. However, the high temperatures and high strength caused by the nickel-based materials during cutting also reduce the tool lifetime. This research aims to investigate the tool wear and the surface roughness of Waspaloy during cutting with various cutting speeds, feed per tooth, cutting depth, and other cutting parameters. Then, it derives the formula for the tool lifetime based on the experimental results and explores the impacts of these cutting parameters on the cutting of Waspaloy. Since the impacts of cutting speed on the cutting of Waspaloy are most significant in accordance with the experimental results, the high-speed cutting is not recommended. In addition, the actual surface roughness of Waspaloy is worse than the theoretical surface roughness in case of more tool wear. Finally, a set of mathematical models can be established based on these results, in order to predict the surface roughness of Waspaloy cut with a worn tool. The errors between the predictive values and the actual values are 5.122%∼8.646%. If the surface roughness is within the tolerance, the model can be used to predict the residual tool lifetime before the tool is damaged completely. The errors between the predictive values and the actual values are 8.014%∼20.479%.

Turning of Inconel 718 by Cemented Carbides

2011 ◽  
Vol 496 ◽  
pp. 138-143 ◽  
Author(s):  
Ivan Mrkvica ◽  
Ryszard Konderla ◽  
Miroslav Faktor
Keyword(s):  
Tool Wear ◽  
Inconel 718 ◽  
Cutting Parameters ◽  
Nickel Superalloy ◽  
Cutting Conditions ◽  
Cutting Process ◽  
Cemented Carbides ◽  
Dry Turning ◽  
Cutting Inserts

This article deals with dry turning of nickel superalloy - Inconel 718. The different cemented carbides were applied for cutting process. These inserts were produced by Pramet Tools Ltd. company. This paper discusses durability of cutting inserts, the different intensity of tool wear at various cutting parameters. The most suitable cutting conditions are chosen in the scope of applied tools.

Sign in / Sign up

Export Citation Format

Share Document