Effect of sintering temperature on nonlinearity and surge degradation characteristics of Mn3O4/Nb2O5/Er2O3-doped ZnO–V2O5-based varistors

2019 ◽  
Vol 57 (1) ◽  
pp. 65-72
Author(s):  
Choon-W. Nahm
Keyword(s):  
Sintering Temperature ◽  
Doped Zno

Impact of sintering temperature on structural, optical and ferroelectric properties of V-doped ZnO

2015 ◽  
Vol 2 (4) ◽  
pp. 045901 ◽  
Author(s):  
Parmod Kumar ◽  
Rahul Joshi ◽  
Anurag Gaur ◽  
Lalit Kumar ◽  
K Asokan
Keyword(s):  
Sintering Temperature ◽  
Ferroelectric Properties ◽  
Doped Zno

Electrical Conductivity Measurements of Al-Doped ZnO Semiconductor in High Temperature

2018 ◽  
Vol 772 ◽  
pp. 105-109
Author(s):  
Syamsul Hadi ◽  
Husein Jaya Andika ◽  
Agus Kurniawan ◽  
Suyitno
Keyword(s):  
Electrical Conductivity ◽  
Temperature Effects ◽  
Sintering Temperature ◽  
High Porosity ◽  
Conductivity Measurements ◽  
Grain Sizes ◽  
Lower Porosity ◽  
Doped Zno ◽  
Zno Semiconductor ◽  
Zno Doping

Electrical conductivity plays an important role in the performance of thermoelectric semiconductor material. This study discusses the electrical conductivity measurements of Zinc Oxide (ZnO) doping Aluminium (Al) pellet as a material of thermoelectric using four-point probe method at high temperatures. Al-doped ZnO (2 wt%) pellet was sintered at the temperature of 1100°C, 1200°C, 1300°C, 1400°C, and 1500°C with the heating rate of 8°C/minute. SEM and XRD tests show that the higher sintering temperature effects to larger grain sizes, better crystallinity, and lower porosity. There is no electrical conductivity in the sintering sample at 1100°C due to the small grain sizes and high porosity. In the sintering sample at 1500°C, the phase of ZnAl2O4erupted. The highest electrical conductivity of 5923.48S/m of Al-doped ZnO pellet was obtained at the sintering temperature of 1400°C with measurement temperature of 500°C.

The Influence of AST Doping on the Dielectric Properties of MgTiO3-Based Ceramics Fabricated by Soild-State Sintering

2013 ◽  
Vol 634-638 ◽  
pp. 2378-2382
Author(s):  
Chun Yuan Luo ◽  
Jing Xiao Liu ◽  
Fei Shi ◽  
Ji Wei Wu ◽  
Chao Qian ◽  
...  
Keyword(s):  
Dielectric Properties ◽  
Solid State ◽  
Liquid Phase ◽  
Dielectric Loss ◽  
Sintering Temperature ◽  
Liquid Phase Sintering ◽  
Sintering Process ◽  
Solid State Sintering ◽  
Doped Zno

AST-doped ZnO-MgTiO3-SrTiO3ceramics were prepared using a solid-state sintering process. The effects of AST (Al2O3-SiO2-TiO2) on the dielectric properties of MgTiO3-based ceramics were investigated. The results indicate that AST-doped MgTiO3-based ceramics could be obtained after 1205~1280°C sintering for 3 h. The XRD results indicate that the obtained MgTiO3-based ceramics contain high percentage of MgTi2O5 phase and the percentage increased with the increase of AST content. It was found that the occurred liquid-phase sintering by adding AST glass could effectively lower the sintering temperature and decrease the dielectric loss of MgTiO3-based ceramics. A minimum tanδ of 1.5×10-4 associated with εr=19.0 was achieved for 6.0 wt% AST-doped samples sintered at 1255°C.

On the Grain Size Distribution of MnO Doped ZnO Ceramics

2007 ◽  
Vol 336-338 ◽  
pp. 2361-2362
Author(s):  
Shu Ai Li ◽  
Da Nian Liu ◽  
Jiang Hong Gong
Keyword(s):  
Grain Size ◽  
Size Distribution ◽  
Grain Size Distribution ◽  
Sintering Temperature ◽  
Grain Morphology ◽  
Holding Time ◽  
Grain Sizes ◽  
Different Temperatures ◽  
Doped Zno ◽  
Zno Ceramics

A series of MnO-doped ZnO with different grain sizes and grain morphologies were prepared by sintering the samples at different temperatures for different holding times. The grain size distribution for each sample was determined. It was found that, although the grain size increases and the grain morphology varies with the sintering temperature and/or the holding time, the normalized grain size distribution keeps invariable.

Sign in / Sign up

Export Citation Format

Share Document