Comparison of cycle-by-cycle variation of measured exhaust-gas temperature and in-cylinder pressure measurements

2010 ◽  
Vol 30 (5) ◽  
pp. 487-491 ◽  
Author(s):  
Francis Morey ◽  
Patrice Seers
Keyword(s):  
Exhaust Gas ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Cycle Variation ◽  
Exhaust Gas Temperature

Cylinder Pressure Information-Based Postinjection Timing Control for Aftertreatment System Regeneration in a Diesel Engine—Part II: Active Diesel Particulate Filter Regeneration

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Hyunjun Lee ◽  
Jaesik Shin ◽  
Manbae Han ◽  
Myoungho Sunwoo
Keyword(s):  
Diesel Particulate Filter ◽  
Fuel Injection ◽  
Control Method ◽  
Particulate Filter ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Diesel Particulate ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

The successful utilization of a diesel particulate filter (DPF) to reduce particulate matter (PM) in a passenger car diesel engine necessitates a periodic regeneration of the DPF catalyst without deterioration of the drivability and emission control performance. For successful active DPF regeneration, the exhaust gas temperature should be over 500 °C to oxidize the soot loaded in the DPF. Previous research increased the exhaust gas temperature by applying early and late post fuel injection with a look-up table (LUT) based feedforward control implemented into the engine management system (EMS). However, this method requires enormous calibration work to find the optimal timing and quantity of the main, early, and late post fuel injection with less certainty of accurate torque control. To address this issue, we propose a cylinder pressure based multiple fuel injection (MFI) control method for active DPF regeneration. The feedback control of the indicated mean effective pressure (IMEP), lambda, and DPF upstream temperature was applied to precisely control the injection quantity of the main, early, and late post fuel injection. To determine their fuel injection timings, a mass fraction burned 60% after location of the rate of heat release maximum (MFB60aLoROHRmax) was proposed based on the cylinder pressure information. The proposed control method was implemented in an in-house EMS and validated at several engine operating conditions. During the regeneration period, the exhaust gas temperature tracked the desired temperature, and the engine torque fluctuation was minimized with minimal PM and NOx emissions.

scholarly journals THE RESEARCH OF SIMPLIFICATION OF 1.9 TDI DIESEL ENGINE HEAT RELEASE PARAMETERS DETERMINATION / 1,9 TDI DYZELINIO VARIKLIO ŠILUMOS IŠSISKYRIMO PARAMETRŲ NUSTATYMO SUPAPRASTINIMO TYRIMAS

2014 ◽  
Vol 6 (5) ◽  
pp. 570-576
Author(s):  
Justas Žaglinskis ◽  
Kristóf Lukács ◽  
Ákos Bereczky ◽  
Paulius Rapalis
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Study Results ◽  
Release Data ◽  
Exhaust Gas Temperature ◽  
Main Engine

The investigation of modified methodology of Audi 1.9 TDI 1Z diesel engine heat release parameters’ determination is represented in the article. In this research the AVL BOOST BURN and IMPULS software was used to treat data and to simulate engine work process. The reverse task of indicated pressure determination from heat release data was solved here. T. Bulaty and W. Glanzman methodology was modified for purpose to simplify the determination of heat release parameters. The maximal cylinder pressure, which requires additional expensive equipment, was changed into the objective indicator – exhaust gas temperature. This modification allowed to simplify the experimental engine tests and also gave simulation results in an error range up to 2% of main engine operating parameters. The study results are assessed as an important point for the simplification of engine test under field conditions. Straipsnyje pateikta dyzelinio Audi variklio 1,9 TDI 1Z šilumos išsiskyrimo parametrų nustatymo metodikos ir jos modifikavimo tyrimas. Šio tyrimo procese atilikto eksperimento duomenims apdoroti ir darbo procesui modeliuoti panaudoti AVL BOOST BURN ir IMPULS programiniai paketai. Tyrime buvo sprendžiamas atvirkščias indikatorinio slėgio nustatymo iš šilumos charakteristikos duomenų uždavinys. Siekiant supaprastinti šilumos išsiskyrimo parametrų nustatymą, panaudota modifikuota T. Bulaty ir W. Glanzman metodika. Maksimalaus slėgio cilindre parametras, kurio nustatymas reikalauja papildomos brangios įrangos, buvo pakeistas objektyviu išmetamųjų dujų temperatūros parametru. Šis modifikavimas leidžia supaprastinti eksperimentinius tyrimus bei leido atlikti pagrindinių variklio darbo parametrų modeliavimą neviršijant 2 % paklaidų ribos. Tyrimo rezultatas vertinamas itin svarbiu variklių bandymų lauko sąlygomis supaprastinimo atžvilgiu.

scholarly journals Analisa Waktu Operasi Terhadap Temperatur dan Tekanan pada Mesin Diesel

Jurnal METTEK ◽  
2021 ◽  
Vol 7 (1) ◽  
pp. 39
Author(s):  
Nasmi Herlina Sari ◽  
Suteja Suteja ◽  
Yudi Ahmad Efendi
Keyword(s):  
The Other ◽  
Control Panel ◽  
Exhaust Gas ◽  
Engine Control ◽  
Pressure Measurements ◽  
Gas Temperature ◽  
Temperature And Pressure ◽  
Engine Components ◽  
Exhaust Gas Temperature ◽  
Temperature Side

Studi ini bertujuan untuk menganalisa temperatur, dan tekanan pada setiap komponen mesin Mesin diesel Sulzer 16 ZAV 40S selama beroperasi 8 jam. Penelitian ini dilakukan di PT. Iradat Aman Sektor Pringgabaya Lombok. Engine Control Panel (ECP) dan Generator Control Panel (GCP) telah digunakan untuk menentukan nilai dari tekanan, dan temperatur berdasarkan sensor yang telah dipasang pada komponen mesin. Pengukuran temperatur dan tekanan dilakukan setiap jam selama 8 jam. Hasil penelitian menunjukan bahwa setelah mesin beroperasi selama 4 jam sampai 7 jam; temperatur stator, temperatur gas buang, temperature silinder sisi A dan silider sisi B mengalami penurunan yang signifikan dikarenakan kebocoran pada silinder A dan B. Sedangkan tekanan pada mesin masih normal dan tidak mengalami perubahan yang signifikan. This study aims to analyze the temperature and pressure of each component of the Sulzer 16 ZAV 40S diesel engine for 8 hours of operation. This research was conducted at PT. Iradat Aman Sector Pringga Baya Lombok. The Engine Control Panel (ECP) and Generator Control Panel (GCP) have been used to determine the value of pressure and temperature based on sensors that have been installed on engine components. Temperature and pressure measurements were carried out every hour for 8 hours. The results showed that after the machine operated for 4 hours to 7 hours; stator temperature, exhaust gas temperature, cylinder temperature side A and side cylinder B experienced a significant decrease due to leaks in cylinders A and B. On the other hand, the pressure on the engine was still normal and did not experience a significant change.

Performance and Emissions of Acetone-Butanol-Ethanol (ABE) and Gasoline Blends in a Port Fuel Injected Spark Ignition Engine

2014 ◽  
Author(s):  
Karthik Nithyanandan ◽  
Chia-fon F. Lee ◽  
Han Wu ◽  
Jiaxiang Zhang
Keyword(s):  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Exhaust Gas ◽  
Engine Fuel ◽  
Cylinder Pressure ◽  
Gas Temperature ◽  
Promising Alternative ◽  
Unburned Hydrocarbons ◽  
Exhaust Gas Temperature ◽  
Acetone Butanol Ethanol

Acetone-Butanol-Ethanol (ABE), an intermediate product in the ABE fermentation process for producing bio-butanol, is considered a promising alternative fuel because it not only preserves the advantages of oxygenated fuels which typically emit fewer pollutants, but also lowers the cost of fuel recovery for each individual component during fermentation. An experiment was conducted using a Ford single-cylinder spark-ignition (SI) research engine to investigate the potential of ABE as an SI engine fuel. Blends of pure gasoline and ABE, ranging from 0% to 80% vol. ABE, were created and the performance and emission characteristics were compared with pure gasoline as the baseline. Measurements of brake torque and exhaust gas temperature along with in-cylinder pressure traces were used to study the performance of the engine and measurements of emissions of unburned hydrocarbons, carbon monoxide, and nitrogen oxides were used to compare the fuels in terms of combustion byproducts. Experiments were performed at a constant engine speed and a comparison was made on the basis of similar power output (Brake Mean Effective Pressure (BMEP)). In-cylinder pressure data showed that the peak pressure of all the blends was slightly lower than that of gasoline, except for ABE80 which showed a slightly higher and advanced peak relative to gasoline. ABE showed an increase in brake specific fuel consumption (BSFC); while exhaust gas temperature and nitrogen oxide measurements show that ABE combusts at a lower peak temperature. The emissions of unburned hydrocarbons were higher compared to those of gasoline but the CO emissions were lower. Of particular interest is the combined effect of the higher laminar flame speed (LFS) and higher latent heat of vaporization of ABE fuels on the combustion process.

scholarly journals Diesel engine performance, emissions and combustion characteristics of castor oil blends using pyrolysis

2020 ◽  
Vol 12 (12) ◽  
pp. 168781402097552
Author(s):  
Youssef A. Attai ◽  
Osayed S. Abu-Elyazeed ◽  
Mohamed R. ElBeshbeshy ◽  
Mohamed A. Ramadan ◽  
Mohamed S. Gad
Keyword(s):  
Heat Release ◽  
Fuel Consumption ◽  
Heat Release Rate ◽  
Release Rate ◽  
Thermal Efficiency ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Gas Oil ◽  
Gas Temperature ◽  
Exhaust Gas Temperature

Castor biodiesel (CBD) was manufactured by slow pyrolysis of oil from highly yielded seeds with anhydrous sodium hydroxide catalyst. An experimental study of engine’s performance, emissions and combustion characteristics using biodiesel blended with gas oil in volumetric ratios of 0, 10, 25, 50, 75, and 100% at different loads was performed. Increase of CBD percentage in the blend led to a reduction in engine’s thermal efficiency, cylinder pressure, net heat release rate, and smoke emission. The exhaust gas temperature, specific fuel consumption, unburned hydrocarbon, CO, and nitrogen oxide emissions were increased with the increase of CBD ratio. Biodiesel showed the maximum increase in specific fuel consumption by 10% and the thermal efficiency was decreased by 10.5% about pure diesel. Smoke emissions were decreased for CBD100 by 12% about gas oil. The maximum increases in NOx, CO, HC emissions, and exhaust gas temperature for CBD 100 were 22, 34, 48, and 11%, respectively related to diesel oil. The maximum reductions in cylinder pressure and net heat release rate were 5 and 13% for CBD100 about gas oil, respectively. Biodiesel percentage of 10% showed near values of performance parameters and emissions to gas oil, so, it is recommended as the optimum percentage.

Lime kiln conversion from coke to natural gas operation – an option in direction of sustainable energy

2020 ◽  
pp. 431-434
Author(s):  
Oliver Arndt
Keyword(s):  
Natural Gas ◽  
New Technology ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Gaseous Fuels ◽  
Lime Kiln ◽  
Lime Kilns ◽  
Co2 Balance ◽  
Exhaust Gas Temperature

This paper deals with the conversion of coke fired lime kilns to gas and the conclusions drawn from the completed projects. The paper presents (1) the decision process associated with the adoption of the new technology, (2) the necessary steps of the conversion, (3) the experiences and issues which occurred during the first campaign, (4) the impacts on the beet sugar factory (i.e. on the CO2 balance and exhaust gas temperature), (5) the long term impressions and capabilities of several campaigns of operation, (6) the details of available technologies and (7) additional benefits that would justify a conversion from coke to natural gas operation on existing lime kilns. (8) Forecast view to develop systems usable for alternative gaseous fuels (e.g. biogas).

scholarly journals Exhaust Gas Temperature Measurements in Diagnostics of Turbocharged Marine Internal Combustion Engines Part I Standard Measurements

2015 ◽  
Vol 22 (1) ◽  
pp. 47-54 ◽  
Author(s):  
Zbigniew Korczewski
Keyword(s):  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Technical Condition ◽  
Temperature Measurements ◽  
Injection System ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Gas Temperature ◽  
Measuring Signal ◽  
Exhaust Gas Temperature

Abstract The article discusses the problem of diagnostic informativeness of exhaust gas temperature measurements in turbocharged marine internal combustion engines. Theoretical principles of the process of exhaust gas flow in turbocharger inlet channels are analysed in its dynamic and energetic aspects. Diagnostic parameters are defined which enable to formulate general evaluation of technical condition of the engine based on standard online measurements of the exhaust gas temperature. A proposal is made to extend the parametric methods of diagnosing workspaces in turbocharged marine engines by analysing time-histories of enthalpy changes of the exhaust gas flowing to the turbocompressor turbine. Such a time-history can be worked out based on dynamic measurements of the exhaust gas temperature, performed using a specially designed sheathed thermocouple. The first part of the article discusses possibilities to perform diagnostic inference about technical condition of a marine engine with pulse turbocharging system based on standard measurements of exhaust gas temperature in characteristic control cross-sections of its thermal and flow system. Selected metrological issues of online exhaust gas temperature measurements in those engines are discusses in detail, with special attention being focused on the observed disturbances and thermodynamic interpretation of the recorded measuring signal. Diagnostic informativeness of the exhaust gas temperature measurements performed in steady-state conditions of engine operation is analysed in the context of possible evaluations of technical condition of the engine workspaces, the injection system, and the fuel delivery process.

Energetic Based Organic Fluid Selection for a Solid Oxide Fuel Cell-Organic Rankine Cycle Combined System

2012 ◽  
Vol 622-623 ◽  
pp. 1162-1167
Author(s):  
Han Fei Tuo
Keyword(s):  
Fuel Cell ◽  
Solid Oxide Fuel Cell ◽  
Heat Recovery ◽  
Waste Heat ◽  
Solid Oxide ◽  
Exhaust Gas ◽  
Oxide Fuel ◽  
Gas Temperature ◽  
Selection For ◽  
Exhaust Gas Temperature

In this study, energetic based fluid selection for a solid oxide fuel cell-organic rankine combined power system is investigated. 9 dry organic fluids with varied critical temperatures are chosen and their corresponding ORC cycle performances are evaluated at different turbine inlet temperatures and exhaust gas temperature (waste heat source) from the upper cycle. It is found that actual ORC cycle efficiency for each fluid strongly depends on the waste heat recovery performance of the heat recovery vapor generator. Exhaust gas temperature determines the optimal fluid which yields the highest efficiency.

Experimental Study of Natural Gas Fuel Temperature Influence on Radiation Enhancement and Emission

2010 ◽  
Author(s):  
S. Mohammad Javadi ◽  
Pourya Nikoueeyan ◽  
Mohammad Moghiman ◽  
M. Ebrahim Feyz
Keyword(s):  
Radiation Intensity ◽  
Flame Temperature ◽  
Photovoltaic Module ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Fuel Temperature ◽  
Flame Radiation ◽  
Exhaust Gases ◽  
No Formation ◽  
Exhaust Gas Temperature

The enhancement of the flame radiation in gas fueled burners not only improves the thermal efficiency, but also can suppress the rate of NO emission due to reducing the flame temperature. In this experimental investigation, the effect of inlet gas temperature on the flame radiation intensity and the rate of NO formation are studied. To serve this aim, with increasing the temperature of inlet methane to the burner up to 310°C, the variations of CO and NO level in exhaust gases and also the exhaust gas temperature are recorded by gas analyzer device. In each case, the flame radiation intensity was also measured by a photovoltaic module. The results revealed that by increasing the inlet gas temperature up to 250°C, the NO concentration and the exhaust gases temperature are raising. But when the inlet gas temperature exceeds from 250°C and reaches to 310°C, the flame luminosity gradually increases which results in 70 percent growth in flame radiation and 10 percent drop in exhaust gas temperature. The results of the preheating of inlet air also show the same behavior.

Sign in / Sign up

Export Citation Format

Share Document