scholarly journals Investigation of C-S-H in ternary cement pastes containing nanosilica and highly-reactive supplementary cementitious materials (SCMs): Microstructure and strength

2019 ◽  
Vol 198 ◽  
pp. 445-455 ◽  
Author(s):  
Daniel da Silva Andrade ◽  
João Henrique da Silva Rêgo ◽  
Paulo Cesar Morais ◽  
Anne Neiry de Mendonça Lopes ◽  
Moisés Frías Rojas
Keyword(s):  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Cement Pastes

scholarly journals New Approach for the Determination of Radiological Parameters on Hardened Cement Pastes with Coal Fly Ash

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 475
Author(s):  
Ana María Moreno de los Reyes ◽  
José Antonio Suárez-Navarro ◽  
Maria del Mar Alonso ◽  
Catalina Gascó ◽  
Isabel Sobrados ◽  
...  
Keyword(s):  
Fly Ash ◽  
Activity Concentration ◽  
Gamma Ray ◽  
Coal Fly Ash ◽  
Cementitious Materials ◽  
New Method ◽  
Supplementary Cementitious Materials ◽  
Hardened Cement ◽  
Cement Pastes ◽  
Activity Concentrations

Supplementary cementitious materials (SCMs) in industrial waste and by-products are routinely used to mitigate the adverse environmental effects of, and lower the energy consumption associated with, ordinary Portland cement (OPC) manufacture. Many such SCMs, such as type F coal fly ash (FA), are naturally occurring radioactive materials (NORMs). 226Ra, 232Th and 40K radionuclide activity concentration, information needed to determine what is known as the gamma-ray activity concentration index (ACI), is normally collected from ground cement samples. The present study aims to validate a new method for calculating the ACI from measurements made on unground 5 cm cubic specimens. Mechanical, mineralogical and radiological characterisation of 28-day OPC + FA pastes (bearing up to 30 wt % FA) were characterised to determine their mechanical, mineralogical and radiological properties. The activity concentrations found for 226Ra, 212Pb, 232Th and 40K in hardened, intact 5 cm cubic specimens were also statistically equal to the theoretically calculated values and to the same materials when ground to a powder. These findings consequently validated the new method. The possibility of determining the activity concentrations needed to establish the ACI for cement-based materials on unground samples introduces a new field of radiological research on actual cement, mortar and concrete materials.

scholarly journals Mechanically activated mine tailings for use as supplementary cementitious materials

2021 ◽  
Vol 6 ◽  
pp. 61-69
Author(s):  
Sivakumar Ramanathan ◽  
Priyadarshini Perumal ◽  
Mirja Illikainen ◽  
Prannoy Suraneni
Keyword(s):  
Mine Tailings ◽  
Isothermal Calorimetry ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Strong Correlations ◽  
Negative Effects ◽  
Cement Pastes ◽  
Amorphous Content ◽  
Milling Duration ◽  
Median Particle

Two mine tailings are evaluated for their potential as supplementary cementitious materials. The mine tailings were milled using two different methods – ball milling for 30 minutes and disc milling for durations ranging from 1 to 15 minutes. The modified R3 test was carried out on the mine tailings to quantify their reactivity. The reactivity of the disc milled tailings is greater than those of the ball milled tailings. Strong correlations are obtained between milling duration, median particle size, amorphous content, dissolved aluminum and silicon, and reactivity of the mine tailings. The milling energy results in an increase in the fineness and the amorphous content, which do not appreciably increase beyond a disc milling duration of 8 minutes. The reactivity increases significantly beyond a certain threshold fineness and amorphous content. Cementitious pastes were prepared at 30% supplementary cementitious materials replacement level at a water-to-cementitious materials ratio of 0.40. No negative effects of the mine tailings were observed at early ages in cement pastes based on isothermal calorimetry and thermogravimetric analysis, demonstrating the potential for these materials to be used as supplementary cementitious materials.

scholarly journals Synthesis of a New Polycarboxylate at Room Temperature and Its Influence on the Properties of Cement Pastes with Different Supplementary Cementitious Materials

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Shuncheng Xiang ◽  
Yingli Gao ◽  
Caijun Shi
Keyword(s):  
Room Temperature ◽  
Autogenous Shrinkage ◽  
Drying Shrinkage ◽  
Cementitious Materials ◽  
Heat Evolution ◽  
Hydration Heat ◽  
Supplementary Cementitious Materials ◽  
Cement Pastes ◽  
Binder Ratio ◽  
Water Binder Ratio

Three polycarboxylates with different comb structures (i.e., the same degree of polymerization in side chains but different main chains) were synthesized via radical polymerization reaction at room temperature. The effect of polycarboxylates on the surface tension and the flowability in cement pastes was determined. The best product was selected to study its effects on the hydration heat evolution, compressive strength, autogenous shrinkage, and drying shrinkage of cement pastes with different kinds and contents of supplementary cementitious materials. The results showed that with the increase of molar ratio between AA and TPEG to 6 : 1, we could synthesis the best product. When the water-binder ratio was 0.4, with the increase of polycarboxylates, the cement hydration heat evolution had been slowed down, and the more the dosage was, the more obvious the effect was. Adding supplementary cementitious materials to cement under the same experimental conditions also played a mitigation role in slowing down the hydration heat. When the water-binder ratio was 0.3, supplementary cementitious materials could increase the strength of cement by 24.5% in maximum; its autogenous shrinkage and drying shrinkage could be decreased, respectively, by 60.1% and 21.9% in the lowest.

scholarly journals Suitability of Remediated PFAS-Affected Soil in Cement Pastes and Mortars

2020 ◽  
Vol 12 (10) ◽  
pp. 4300
Author(s):  
Andras Fehervari ◽  
Will P. Gates ◽  
Chathuranga Gallage ◽  
Frank Collins
Keyword(s):  
Contaminated Soils ◽  
Strength Loss ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Fine Aggregate ◽  
Cement Pastes ◽  
Supplementary Cementitious Material ◽  
Treated Soil ◽  
Fine Aggregates ◽  
Heat Treated

Australia and many other parts of the world face issues of contamination in groundwater and soils by per- and poly-fluoroalkyl substances (PFAS). While the pyrolytic treatment of contaminated soils can destroy PFAS, the resulting heat-treated soils currently have limited applications. The purpose of this study was to demonstrate the usefulness of remediated soils in concrete applications. Using heat-treated soil as a fine aggregate, with a composition and particle size distribution similar to that of traditional concrete sands, proved to be a straightforward process. In such situations, complete fine aggregate replacement could be achieved with minimal loss of compressive strength. At high fine aggregate replacement (≥ 60%), a wetting agent was required for maintaining adequate workability. When using the heat-treated soil as a supplementary cementitious material, the initial mineralogy, the temperature of the heat-treatment and the post-treatment storage (i.e., keeping the soil dry) were found to be key factors. For cement mortars where minimal strength loss is desired, up to 15% of cement can be replaced, but up to 45% replacement can be achieved if moderate strengths are acceptable. This study successfully demonstrates that commercially heat-treated remediated soils can serve as supplementary cementitious materials or to replace fine aggregates in concrete applications.

Relationship between Internal Relative Humidity and Autogenous Shrinkage of Cement Paste with Supplementary Cementitious Materials (SCM)

2013 ◽  
Vol 539 ◽  
pp. 35-39 ◽  
Author(s):  
Yue Li ◽  
Qian Qian Yan
Keyword(s):  
Fly Ash ◽  
Relative Humidity ◽  
Autogenous Shrinkage ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Cement Pastes ◽  
Different Types ◽  
Influence Of Water ◽  
Internal Relative Humidity ◽  
Main Factor

The influence of water to binder (W/B), types and dosage of supplementary cementitious materials (SCM) on the internal relative humidity (IRH) and autogenous shrinkage (AS) of cement pastes caused by self-desiccation were investigated, and their relationship was discussed. The results show that, W/B is a main factor that affects IRH change and AS of cement pastes with SCM. With the decrease of W/B, IRH of cement pastes decreases, but AS of cement pastes increases. Different types and dosages of SCM affect the IRH differently; fly ash (FA) reduces AS, silica fume (SF) increases AS, and the effect of GBFS on AS is between FA and GBFS. The linear correlation between the change of IRH and AS of cement pastes with SCM is established.

scholarly journals Self-Healing Products of Cement Pastes with Supplementary Cementitious Materials, Calcium Sulfoaluminate and Crystalline Admixtures

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7201
Author(s):  
Byoungsun Park ◽  
Young-Cheol Choi
Keyword(s):  
Phase Composition ◽  
Cementitious Materials ◽  
The Self ◽  
Ion Concentration ◽  
Supplementary Cementitious Materials ◽  
Self Healing ◽  
Cement Pastes ◽  
Main Compound ◽  
Calcium Sulfoaluminate ◽  
Granulated Blast Furnace Slag

The phase composition of self-healing products generated in cracks affects self-healing performance. This study investigated the self-healing products of cementitious materials using supplementary cementitious materials (SCMs), a calcium sulfoaluminate (CSA) expansion agent, and crystalline additives (CAs). Ground-granulated blast-furnace slag (GGBFS), fly ash (FA), and silica fume (SF) were used as SCMs, and anhydrite, Na2SO4, Na2CO3, and MgCO3 were used as crystalline additives (CAs). An artificial crack method was used to collect the self-healing products in the crack of the paste. The phase composition of the self-healing products was analyzed through X-ray diffraction (XRD)/Rietveld refinements and thermogravimetry/differential thermogravimetry (TG/DTG) analysis, and their morphology and ion concentration were examined through scanning electron microscopy with energy dispersive spectroscopy (SEM–EDS). From the results, the main compound of self-healing products was found to be calcite. GGBFS and FA decreased the content of portlandite, and the use of CAs led to the formation of alkali sulfate and alkali carbonate. The SEM–EDS analysis results showed that when GGBFS and FA were used, a large proportion of the self-healing products contained C-S-H and C-A-H, and the use of CSA led to the formation of monosulfate and ettringite.

Sign in / Sign up

Export Citation Format

Share Document