scholarly journals Experimental dataset on the tensile and compressive mechanical properties of plain Kraft and crepe papers used as insulation in power transformers after ageing in mineral oil

Data in Brief ◽  
2021 ◽  
Vol 36 ◽  
pp. 107031
Author(s):  
Carmela Oria ◽  
Isidro Carrascal ◽  
Diego Ferreño ◽  
Inmaculada Fernández ◽  
Alfredo Ortiz
Keyword(s):  
Mechanical Properties ◽  
Mineral Oil ◽  
Power Transformers ◽  
Experimental Dataset

scholarly journals Kinetic Assessment of Mechanical Properties of a Cellulose Board Aged in Mineral Oil and Synthetic Ester

Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4150
Author(s):  
Cristina Fernández-Diego ◽  
Alfredo Ortiz ◽  
Isidro A. Carrascal ◽  
Inmaculada Fernández ◽  
Carlos J. Renedo
Keyword(s):  
Mechanical Properties ◽  
Kinetic Models ◽  
Mineral Oil ◽  
Power Transformers ◽  
Fiber Direction ◽  
Insulation System ◽  
Synthetic Ester ◽  
Aging Study ◽  
Kinetic Assessment ◽  
Materials Used

In oil-immersed power transformers, the insulation system is constituted of a dielectric oil–solid combination. The insulation oil generally used is mineral oil; however, this fluid has started to be substituted by natural and synthetic esters due to their higher biodegradability and flash point. The introduction of a new fluid in the insulation system of power transformers requires kinetic models that can estimate the degradation rate of insulation solids. The aim of this work was to go further in quantifying through different kinetic models the deterioration suffered by a commercial cellulose board (PSP 3055), which is one of the solid materials used in the insulation system of oil-filled transformers. The aging study was extended to cellulose board specimens immersed in two different oils (mineral and synthetic ester). It was obtained that there is a lower degradation when synthetic ester is used in the insulation system. Additionally, it can be concluded that the use of mechanical properties to quantify the degradation of the cellulose board through kinetic models provides information about the different behavior shown by PSP 3055 when different fiber direction angles are considered.

scholarly journals Decoupling of Mechanical and Transport Properties in Organogels via Solvent Variation

Gels ◽  
2021 ◽  
Vol 7 (2) ◽  
pp. 61
Author(s):  
Kenneth P. Mineart ◽  
Cameron Hong ◽  
Lucas A. Rankin
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Transdermal Drug Delivery ◽  
Triblock Copolymer ◽  
Polymer Concentration ◽  
Mineral Oil ◽  
Solute Diffusion ◽  
Oil Viscosity ◽  
Chain Entanglement ◽  
Mineral Oils

Organogels have recently been considered as materials for transdermal drug delivery media, wherein their transport and mechanical properties are among the most important considerations. Transport through organogels has only recently been investigated and findings highlight an inextricable link between gels’ transport and mechanical properties based upon the formulated polymer concentration. Here, organogels composed of styrenic triblock copolymer and different aliphatic mineral oils, each with a unique dynamic viscosity, are characterized in terms of their quasi-static uniaxial mechanical behavior and the internal diffusion of two unique solute penetrants. Mechanical testing results indicate that variation of mineral oil viscosity does not affect gel mechanical behavior. This likely stems from negligible changes in the interactions between mineral oils and the block copolymer, which leads to consistent crosslinked network structure and chain entanglement (at a fixed polymer concentration). Conversely, results from diffusion experiments highlight that two penetrants—oleic acid (OA) and aggregated aerosol-OT (AOT)—diffuse through gels at a rate inversely proportional to mineral oil viscosity. The inverse dependence is theoretically supported by the hydrodynamic model of solute diffusion through gels. Collectively, our results show that organogel solvent variation can be used as a design parameter to tailor solute transport through gels while maintaining fixed mechanical properties.

Electrophysical properties of mixtures of mineral oil and synthetic ester dielectric liquid

2021 ◽  
Vol 14 (2) ◽  
pp. 132-141
Author(s):  
M. N. Lyutikova ◽  
S. M. Korobeynikov ◽  
A. A. Konovalov
Keyword(s):  
Dielectric Loss ◽  
Breakdown Voltage ◽  
Loss Tangent ◽  
Dielectric Loss Tangent ◽  
Kinematic Viscosity ◽  
Mineral Oil ◽  
Flash Point ◽  
Power Transformers ◽  
Synthetic Ester ◽  
Insulating Properties

Power transformers are key equipment in power generation, transmission, and distribution systems. The reliability of power transformers is based on the performance of the insulation system, which includes solid cellulose insulation and a liquid dielectric. Modern power engineering requires liquid insulation to have excellent insulating properties, high fire resistance, and biodegradability. Mineral oil that has been in use for over 100 years does not meet certain requirements. Therefore, various methods of enhancing the insulating properties of the oil are currently being considered, including mixing it with other liquid dielectrics, which have excellent properties. Synthetic and natural esters are considered as alternative fluids.This article discusses the possibility of enhancing the insulating characteristics of mineral oil with a high content of aromatic hydrocarbons (for example, T-750 oil) by mixing it with synthetic ester Midel 7131. Assessment is given of insulating parameters of the resulting mixtures with an ester fraction in mineral oil from 0% to fifty%. The main characteristics of the mixtures are described, such as density, kinematic viscosity, flash point, dielectric loss tangent, relative dielectric permittivity, breakdown voltage, and moisture content. It is shown that with an increase in the proportion of ester, some parameters of the obtained insulating liquid improve (flash point, dielectric constant, breakdown voltage), while values of other parameters (density, kinematic viscosity, dielectric loss tangent) with an ester content of more than 10% in the mixture do not meet the requirements for mineral oils.

scholarly journals Optimizing characteristics in mineral insulating oil used in high power transformers

2019 ◽  
pp. 222-228
Author(s):  
Irina Alina Chera Anghel ◽  
Loredana Popescu
Keyword(s):  
Mineral Oil ◽  
The Other ◽  
Power Transformers ◽  
Anaerobic Conditions ◽  
Mineral Oils ◽  
Insulating Liquid ◽  
Different Characteristics ◽  
Aerobic And Anaerobic ◽  
Good Heat ◽  
Aerobic And Anaerobic Conditions

The most commonly used insulating liquid in transformers is mineral oil. Special synthetic applications such as silicone, ester, perchloroethene, etc. are used today in special applications, with different characteristics, very low or nonexistent toxicity to mineral oils used in transformers. On the other hand, they have a much better biodegradability than mineral oils in both aerobic and anaerobic conditions. But they cannot directly replace the mineral oil in operation or in repaired units. They have dielectric properties and good heat transfer but have limited their use to special transformers due to the relatively high cost and availability.

scholarly journals Comparative analysis of the impact of dissolved decay products on the dielectric performances of natural monoesters and mineral oil for power transformers

2021 ◽  
Vol 14 ◽  
pp. e00977
Author(s):  
Emeric Tchamdjio Nkouetcha ◽  
Ghislain Mengata Mengounou ◽  
Adolphe Moukengue Imano
Keyword(s):  
Comparative Analysis ◽  
Mineral Oil ◽  
Power Transformers ◽  
Decay Products ◽  
The Impact

scholarly journals Comparative Study on Mechanical Properties of Sealing Grease Composed of Different Base Oils for Shield Tunnel

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 692 ◽  
Author(s):  
Xiangqian Li ◽  
Yuyou Yang ◽  
Fan Li
Keyword(s):  
Mechanical Properties ◽  
Vegetable Oil ◽  
Exponential Function ◽  
Flow Rate ◽  
Temperature Sensitivity ◽  
Mineral Oil ◽  
Shield Tunnel ◽  
Fixed Temperature ◽  
Base Oil ◽  
Base Oils

This study proposes a novel sealing grease with improved mechanical properties and environmental performance. A series of sealing grease samples were made with different base oils, including mineral oil and renewable oil (vegetable oil and lard). In this study, thermogravimetric analysis (TGA) was conducted to study the adsorption capacity of the thickener to the base oil. The fluidity of the sealing grease was also tested at different temperatures. Furthermore, an exponential function was proposed for the flow rate of the sealing grease and the temperature. Moreover, a cone penetration test was conducted to study the consistency of the sealing grease. The results indicated that the capacity of the thickener to adsorb vegetable oil was greater than that of mineral oil, but less than that of lard. Additionally, the flow rate of the sealing grease increased with an increase in temperature. At a fixed temperature, the flow rate of the sealing grease increased with the base oil content. According to the exponential function, the composition of the base oil is the key factor that determines the temperature sensitivity of the sealing grease. In addition, the sealing grease made of vegetable oil has the minimum temperature sensitivity coefficient.

Effect of Waste Vegetable Oil on Cooling Performance and Lifetime of Power Transformers

2020 ◽  
Author(s):  
Ehsan Ebrahimnia-Bajestan ◽  
Mohammad Arjmand ◽  
Hani Tiznobaik
Keyword(s):  
Magnetic Energy ◽  
Power Transformer ◽  
Mineral Oil ◽  
Power Transformers ◽  
Cooling Performance ◽  
Mineral Oils ◽  
Waste Vegetable Oil ◽  
Lower Viscosity ◽  
Insulating Liquid ◽  
Main Factor

Abstract During the operation of a power transformer, a large amount of heat is generated due to the electrical and magnetic energy losses in its core and windings, causing a temperature rise in transformers. This generated heat is known as the main factor for aging the electrical insulating system of a transformer. In this research, we numerically studied the ability of a vegetable-based oil — as an alternative coolant for the petroleum-based oils — on the cooling performance of a power transformer. The studied oil was a biodiesel produced from waste cooking vegetable oils, having lower viscosity compared to traditional mineral oils. We also calculated the aging rate of the transformer in the presence of the biodiesel. The results indicated that compared to the mineral oil, the average hotspot temperature of the transformer is 3 degrees lower when the biodiesel was used. The life expectancy of the transformer with the vegetable-based oil was also significantly longer than the case with mineral oil. In conclusion, this study provided a sustainable way to use an eco-friendly material produced from a waste resource as an alternative insulating liquid for the cooling of power transformers.

scholarly journals Prediction of the Progressive Loss of Winding Clamping Pressure in Power Transformers

2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Shuguo Gao ◽  
Jun Zhao ◽  
Lingming Meng ◽  
Hongliang Liu
Keyword(s):  
Mechanical Properties ◽  
Initial Pressure ◽  
Order Reaction ◽  
Power Transformers ◽  
Pressure Drops ◽  
First Order ◽  
Progressive Loss ◽  
Out Of Plane ◽  
Transformer Winding ◽  
Clamping Pressure

This paper investigates the progressive loss of winding clamping pressure resulted from thermal aging in power transformers. Firstly, out-of-plane stress-strain characteristics of aging pressboards are investigated experimentally and relationship between mechanical properties of pressboards and aging hours is established accordingly. Then, a thermal-mechanical model is built to correlate the aging time with temperature based on the first-order reaction kinetics. Based on the above investigations, the correlation between temperature and mechanical properties of pressboards is obtained and the progressive loss of clamping pressure is predicted. The results show that with the progressive softening of pressboards from aging, the clamping pressure drops linearly under 60°C and nonlinearly over 60°C. The remaining clamping pressure of a transformer winding with 30 years’ service history is only 80.12% and 51.59% of its initial pressure under 50°C and 60°C, respectively.

Silicone-Based Tissue-Mimicking Phantom for Needle Insertion Simulation

2014 ◽  
Vol 8 (2) ◽  
Author(s):  
Yancheng Wang ◽  
Bruce L. Tai ◽  
Hongwei Yu ◽  
Albert J. Shih
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Medical Devices ◽  
Room Temperature ◽  
Needle Insertion ◽  
Mineral Oil ◽  
Medical Procedures ◽  
Insertion Force ◽  
Needle Insertion Force ◽  
Porcine Tissues

Silicone-based tissue-mimicking phantom is widely used as a surrogate of tissue for clinical simulators, allowing clinicians to practice medical procedures and researchers to study the performance of medical devices. This study investigates using the mineral oil in room-temperature vulcanizing silicone to create the desired mechanical properties and needle insertion characteristics of a tissue-mimicking phantom. Silicone samples mixed with 0, 20, 30, and 40 wt. % mineral oil were fabricated for indentation and needle insertion tests and compared to four types of porcine tissues (liver, muscle with the fiber perpendicular or parallel to the needle, and fat). The results demonstrated that the elastic modulus and needle insertion force of the phantom both decrease with an increasing concentration of mineral oil. Use of the mineral oil in silicone could effectively tailor the elastic modulus and needle insertion force to mimic the soft tissue. The silicone mixed with 40 wt. % mineral oil was found to be the best tissue-mimicking phantom and can be utilized for needle-based medical procedures.

Sign in / Sign up

Export Citation Format

Share Document