Effects of direct injection timing and premixed ratio on combustion and emissions characteristics of RCCI (Reactivity Controlled Compression Ignition) with N-heptane/gasoline-like fuels

Energy ◽  
2015 ◽  
Vol 93 ◽  
pp. 383-392 ◽  
Author(s):  
Lifeng Zhu ◽  
Yong Qian ◽  
Xiaole Wang ◽  
Xingcai Lu
Keyword(s):  
Direct Injection ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition

Investigation of the Effect of Injection and Control Strategies on Combustion Instability in Reactivity-Controlled Compression Ignition Engines

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
David T. Klos ◽  
Sage L. Kokjohn
Keyword(s):  
Direct Injection ◽  
Combustion Instability ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Cfd Modeling ◽  
Surface Model ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition

This paper uses detailed computational fluid dynamics (CFD) modeling with the kiva-chemkin code to investigate the influence of injection timing, combustion phasing, and operating conditions on combustion instability. Using detailed CFD simulations, a large design of experiments (DOE) is performed with small perturbations in the intake and fueling conditions. A response surface model (RSM) is then fit to the DOE results to predict cycle-to-cycle combustion instability. Injection timing had significant tradeoffs between engine efficiency, emissions, and combustion instability. Near top dead center (TDC) injection timing can significantly reduce combustion instability, but the emissions and efficiency drop close to conventional diesel combustion levels. The fuel split between the two direct injection (DI) injections has very little effect on combustion instability. Increasing exhaust gas recirculation (EGR) rate, while making adjustments to maintain combustion phasing, can significantly reduce peak pressure rise rate (PPRR) variation until the engine is on the verge of misfiring. Combustion phasing has a very large impact on combustion instability. More advanced phasing is much more stable, but produces high PPRRs, higher NOx levels, and can be less efficient due to increased heat transfer losses. The results of this study identify operating parameters that can significantly improve the combustion stability of dual-fuel reactivity-controlled compression ignition (RCCI) engines.

RCCI Investigations With n-Butanol and ULSD

2019 ◽  
Author(s):  
Valentin Soloiu ◽  
Cesar E. Carapia ◽  
Justin T. Wiley ◽  
Jose Moncada ◽  
Remi Gaubert ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Ultra Low Sulfur Diesel ◽  
Constant Volume Combustion Chamber ◽  
Soot Emissions ◽  
Low Sulfur

Abstract The focus of this study is to reduce harmful NOx and soot emissions of a compression ignition (CI) engine using reactivity-controlled compression ignition (RCCI) with n-Butanol. RCCI was achieved with the port fuel injection (PFI) of a low reactivity fuel, n-butanol, and a direct injection (DI) of the highly reactive fuel ULSD #2 (Ultra Low Sulfur Diesel) into the combustion chamber. The reactivity, ID, and CD where determined using a Constant Volume Combustion Chamber (CVCC) where ID for n-butanol was found to be 15 times slower than ULSD. The emissions and combustion analysis was conducted at 1500 RPM at an experimental low engine load of 4 bar IMEP; the baseline for emissions comparison was conducted using conventional diesel combustion (CDC) with an injection timing of 16° BTDC at a rail pressure of 800 bar. RCCI was conducted utilizing 75% by mass PFI of n-butanol with 25% ULSD DI, showed a simultaneous reduction of both NOx and soot emissions at a rate of 96.2% and 98.7% respectively albeit with an increase in UHC emissions by a factor of 5. Ringing Intensity was also significantly reduced for Bu75ULSD25 (RCCI Experiment) with a reduction of 62.1% from CDC.

scholarly journals Effect of Injection Timing and Injection Duration of Manifold Injected Fuels in Reactivity Controlled Compression Ignition Engine Operated with Renewable Fuels

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4621
Author(s):  
P. A. Harari ◽  
N. R. Banapurmath ◽  
V. S. Yaliwal ◽  
T. M. Yunus Khan ◽  
Irfan Anjum Badruddin ◽  
...  
Keyword(s):  
Nitric Oxide ◽  
Injection Timing ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Compressed Natural Gas ◽  
Reactivity Controlled Compression Ignition ◽  
Brake Thermal Efficiency ◽  
Injection Duration ◽  
Fuel Mixtures

In the current work, an effort is made to study the influence of injection timing (IT) and injection duration (ID) of manifold injected fuels (MIF) in the reactivity controlled compression ignition (RCCI) engine. Compressed natural gas (CNG) and compressed biogas (CBG) are used as the MIF along with diesel and blends of Thevetia Peruviana methyl ester (TPME) are used as the direct injected fuels (DIF). The ITs of the MIF that were studied includes 45°ATDC, 50°ATDC, and 55°ATDC. Also, present study includes impact of various IDs of the MIF such as 3, 6, and 9 ms on RCCI mode of combustion. The complete experimental work is conducted at 75% of rated power. The results show that among the different ITs studied, the D+CNG mixture exhibits higher brake thermal efficiency (BTE), about 29.32% is observed at 50° ATDC IT, which is about 1.77, 3.58, 5.56, 7.51, and 8.54% higher than D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. The highest BTE, about 30.25%, is found for the D+CNG fuel combination at 6 ms ID, which is about 1.69, 3.48, 5.32%, 7.24, and 9.16% higher as compared with the D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. At all ITs and IDs, higher emissions of nitric oxide (NOx) along with lower emissions of smoke, carbon monoxide (CO), and hydrocarbon (HC) are found for D+CNG mixture as related to other fuel mixtures. At all ITs and IDs, D+CNG gives higher In-cylinder pressure (ICP) and heat release rate (HRR) as compared with other fuel combinations.

An integrated effort of medium reactivity fuel, in-cylinder, and after-treatment strategies to demonstrate potential reduction in challenging emissions of reactivity controlled compression ignition combustion

2019 ◽  
Vol 234 (5) ◽  
pp. 1260-1278
Author(s):  
R Murugan ◽  
D Ganesh ◽  
G Nagarajan
Keyword(s):  
Carbon Monoxide ◽  
Direct Injection ◽  
Cetane Number ◽  
Combustion Process ◽  
Oxidation Catalyst ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Potential Reduction ◽  
Carbon Monoxide Emission ◽  
Compression Ignition Combustion

Previous studies on reactivity controlled compression ignition combustion indicated that, reducing the hydrocarbon and carbon monoxide emissions at low load conditions still remains a challenge because of lower in-cylinder temperatures due to lower global reactivity gradient and reduced oxidation process. Research in this direction has not been reported so far and with this motivation, an attempt has been made to increase the global reactivity gradient and oxidation of fuel–air mixture by converting the low reactivity fuel methanol into medium reactivity fuel. This is achieved by mixing high octane oxygenated fuel, methanol (Octane Number: 110), with an oxygenated better cetane and volatility fuels like polyoxymethylene dimethyl ether (Cetane Number: 78) and isobutanol (Cetane Number: 15). The medium reactivity fuel with multiple direct injection of diesel fuel timed the combustion of dual fuel–air mixture to avoid too late or too advanced combustion which are the prime factors in controlling the unburnt emissions in a low temperature combustion process. Four medium reactivity fuel samples, M80IB20, M60IB40, M90P10, and M80P20, on percentage volume basis have been prepared and tested on the modified on-road three-cylinder turbocharged common rail direct injection diesel engine to demonstrate higher indicated thermal efficiency and potential reduction in unburnt and oxides of nitrogen/particulate matter emissions from reactivity controlled compression ignition combustion. Experimental results show that, use of medium reactivity fuel with optimized diesel injection strategy resulted in 66% decrease in hydrocarbon emission and 74% decrease in carbon monoxide emission by enhancing the oxidation of fuel–air mixture at lower temperatures which is evidently noticed in the combustion characteristics. Further reduction in hydrocarbon and carbon monoxide emission of about 90% has been achieved by integrating the diesel oxidation catalyst with the engine.

Computational optimization of reactivity controlled compression ignition combustion to achieve high efficiency and clean combustion

2020 ◽  
pp. 146808742093173 ◽  
Author(s):  
Avilash Jain ◽  
Anand Krishnasamy ◽  
Pradeep V
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Fuel Injection ◽  
Direct Injection ◽  
Network Models ◽  
Compression Ignition ◽  
Neural Network Models ◽  
Reactivity Controlled Compression Ignition ◽  
Artificial Neural ◽  
Artificial Neural Network Models

One of the major limitations of reactivity controlled compression ignition is higher unburned hydrocarbon and carbon monoxide emissions and lower thermal efficiency at part load operating conditions. In the present study, a combined numerical approach using a commercial three-dimensional computational fluid dynamics code CONVERGE along with artificial neural network and genetic algorithm is presented to address the above limitation. A production light-duty diesel engine is modified to run in reactivity controlled compression ignition by replacing an existing mechanical fuel injection system with a flexible electronic port fuel injection and common rail direct injection systems. The injection schedules of port fuel injection and direct injection injectors are controlled using National Instruments port and direct injection driver modules. Upon validation of combustion and emission parameters, parametric investigations are carried out to establish the effects of direct-injected diesel fuel timing start of injection (SOI), premixed fuel ratio and intake charge temperature on the engine performance and emissions in reactivity controlled compression ignition. The results obtained show that the start of injection timing and intake charge temperature significantly influence combustion phasing, while the premixed fuel ratio controls mixture reactivity and combustion quality. By utilizing the data generated with the validated computational fluid dynamics models, the artificial neural network models are trained to predict the engine exhaust emissions and efficiency. The artificial neural network models for gross indicated efficiency and oxides of nitrogen (NOx) are then coupled with genetic algorithm to maximize gross indicated efficiency while keeping the NOx and soot emissions within Euro VI emission limits. By optimizing the start of injection timing, premixed fuel ratio and intake charge temperature simultaneously using the artificial neural network models coupled with genetic algorithm, 19% improvement in gross indicated efficiency, 60% and 64% reduction in hydrocarbon and carbon monoxide emissions, respectively, are obtained in reactivity controlled compression ignition compared to the baseline case.

Reactivity Controlled Compression Ignition Using Premixed Hydrated Ethanol and Direct Injection Diesel

2012 ◽  
Vol 134 (8) ◽  
Author(s):  
Adam B. Dempsey ◽  
Bishwadipa Das Adhikary ◽  
Sandeep Viswanathan ◽  
Rolf D. Reitz
Keyword(s):  
Direct Injection ◽  
Fuel Efficiency ◽  
High Reactivity ◽  
Water Mixture ◽  
Compression Ignition ◽  
Load Range ◽  
Reactivity Controlled Compression Ignition ◽  
Hcci Combustion ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel

The present study uses numerical simulations to explore the use of hydrated (wet) ethanol for reactivity controlled compression ignition (RCCI) operation in a heavy duty diesel engine. RCCI uses in-cylinder blending of a low reactivity fuel with a high reactivity fuel and has demonstrated significant fuel efficiency and emissions benefits using a variety of fuels, including gasoline and diesel. Combustion timing is controlled by the local blended fuel reactivity (i.e., octane number), and the combustion duration can be controlled by establishing optimized gradients in fuel reactivity in the combustion chamber. In the present study, the low reactivity fuel was hydrated ethanol while the higher reactivity fuel was diesel. First, the effect of water on ethanol/water/diesel mixtures in completely premixed HCCI combustion was investigated using GT-Power and single-zone CHEMKIN simulations. The results showed that the main impact of the water in the ethanol is to reduce the initial in-cylinder temperature due to vaporization cooling. Next, multi-dimensional engine modeling was performed using the KIVA code at engine loads from 5 to 17 bars IMEP at 1300 rev/min with various grades of hydrated ethanol and a fixed diesel fraction of the total fuel. The results show that hydrated ethanol can be used in RCCI combustion with gross indicated thermal efficiencies up to 55% and very low emissions. A 70/30 ethanol/water mixture (by mass) was found to yield the best results across the entire load range without the need for EGR.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

Sign in / Sign up

Export Citation Format

Share Document