Combined effect of silica fume and steel fibers on the impact resistance and mechanical properties of concrete

2010 ◽  
Vol 37 (8) ◽  
pp. 879-886 ◽  
Author(s):  
Mahmoud Nili ◽  
V. Afroughsabet
Keyword(s):  
Mechanical Properties ◽  
Silica Fume ◽  
Impact Resistance ◽  
Steel Fibers ◽  
Combined Effect ◽  
The Impact

Effect of combined drink cans and steel fibers on the impact resistance and mechanical properties of concrete

2020 ◽  
Vol 14 (2) ◽  
pp. 6734-6742
Author(s):  
A. Syamsir ◽  
S. M. Mubin ◽  
N. M. Nor ◽  
V. Anggraini ◽  
S. Nagappan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Indirect Tensile ◽  
The Impact

This study investigated the combine effect of 0.2 % drink cans and steel fibers with volume fractions of 0%, 0.5%, 1%, 1.5%, 2%, 2.5% and 3% to the mechanical properties and impact resistance of concrete. Hooked-end steel fiber with 30 mm and 0.75 mm length and diameter, respectively was selected for this study.  The drinks cans fiber were twisted manually in order to increase friction between fiber and concrete. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the strength performance of concrete, especially the compressive strength, flexural strength and indirect tensile strength. The results of the experiment showed that the combination of steel fibers and drink cans fibers improved the compressive strength, flexural strength and indirect tensile strength by 2.3, 7, and 2 times as compare to batch 1, respectively. Moreover, the impact resistance of fiber reinforced concrete has increase by 7 times as compared to non-fiber concretes. Moreover, the impact resistance of fiber reinforced concrete consistently gave better results as compared to non-fiber concretes. The fiber reinforced concrete turned more ductile as the dosage of fibers was increased and ductility started to decrease slightly after optimum fiber dosage was reached. It was found that concrete with combination of 2% steel and 0.2% drink cans fibers showed the highest compressive, split tensile, flexural as well as impact strength.    

SHPB Dynamic Experiment on Silica Fume Concrete

2013 ◽  
Vol 631-632 ◽  
pp. 771-775 ◽  
Author(s):  
Rong Jun Chen ◽  
Hong Wei Liu ◽  
Rui Zeng
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Silica Fume ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Compression ◽  
Impact Resistance ◽  
Dynamic Mechanical Properties ◽  
Hopkinson Pressure Bar ◽  
The Impact

Dynamic mechanical properties of silica fume concrete in a number of strain rate under the conditions of dynamic compression mechanical properties subjected to various strain rates were studied, and gained the stress versus strain curves, details of an experimental investigation using 74 mm-diameter split Hopkinson pressure bar(SHPB) apparatus were presented. The results showed that: The admixture of silica fume concrete impact resistance, especially under the impact of the performance of high-speed has a very important influence, with the impact velocity increased, the strain rate increase, and its impact more obvious.

scholarly journals Effect of SWCNT-Tuball Paper on the Lightning Strike Protection of CFRPs and Their Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3140
Author(s):  
Kamil Dydek ◽  
Anna Boczkowska ◽  
Rafał Kozera ◽  
Paweł Durałek ◽  
Łukasz Sarniak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Copper Foil ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Lightning Strike ◽  
Single Wall Carbon Nanotubes ◽  
Carbon Fibre Reinforced Polymer ◽  
The Impact

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt% or 90 wt% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

Phase Morphology, Thermal and Mechanical Properties of Compatibilized Nylon12/Natural Rubber Blends Using PS/MNR

2013 ◽  
Vol 844 ◽  
pp. 53-56
Author(s):  
Saravalee Saengthaveep ◽  
Sadhan C. Jana ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Moisture Absorption ◽  
Rubber Particle ◽  
Impact Resistance ◽  
Phase Morphology ◽  
Thermal And Mechanical Properties ◽  
Binary Blend ◽  
Polyamide 12 ◽  
The Impact

To produce a tough material for application demanding high impact resistance and low moisture absorption, melt blending of Nylon12 (Polyamide 12, PA12) and natural rubber (NR) was carried out in a brabender plasticorder at 210 °C with rotor speed of 70 rpm in the presence of polystyrene/maleated natural rubber (PS/MNR) blend as a compatibilizer. The effect of compatibilizer content (1, 3, 5, 7 and 10 phr) on phase morphology, thermal, and mechanical properties of [Nylon12/NR]/[PS/MNR] blends was investigated by using SEM, DSC, and Izod impact tester, respectively. The result revealed that PS/MNR blend improved the compatibility of Nylon12/NR blends efficiently due to the presence of amide linkage at the interfaces from the reaction between the reactive groups of MNR and the NH2 end groups of Nylon12 during mixing. A fine phase morphology (good dispersion and small dispersed phase size of NR domains in Nylon12 matrix) of [Nylon12/NR]/[PS/MNR] blends was observed at the optimum compatibilizer content of 7 phr, relating to the improvement of mechanical property. The impact energy of [Nylon12/NR]/[PS/MNR] blends was 503 J/m higher than that of neat Nylon12 (115 J/m) and Nylon12/NR binary blend (241 J/m) due to the toughening effect of rubber and proper morphology. The melting temperature of all blends did not change obviously from thermal analysis. However, the presence of rubber particle obstructed the crystallization of Nylon12 phase, leading to the decreasing of %crystallinity from 93% to around 70%.

Impact of Steel Fibers on Workability and Properties of UHPC

2016 ◽  
Vol 249 ◽  
pp. 57-61 ◽  
Author(s):  
Milan Rydval ◽  
Tomáš Bittner ◽  
Jiří Kolísko ◽  
Šárka Nenadálová
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
High Performance Concrete ◽  
Volume Fraction ◽  
Fresh Concrete ◽  
Mixture Design ◽  
Steel Fibers ◽  
Hardened Concrete ◽  
Hardened Cement ◽  
The Impact

This paper is focused on properties of fresh and hardened cement-based composite Ultra-High Performance Concrete with regard to different volume fraction of short brass coated steel fibers BASF MASTERFIBER® 482. Workability of fresh concrete and basic mechanical properties (tensile strength in bending, compressive strength) of hardened UHPC were found out. The workability of fresh concrete was measured by small mortar Haegermann cone. Percentage differences at cost were obtained at hardened concrete, too. The aim of the first experimental part of the research was the impact of volume fraction of steel fibers according to workability of fresh concrete and also according to mechanical properties of hardened UHPC with the same volume fraction of each component of the mixture, only the volume fraction of the steel fibers was different at each mixture. The mixture design of UHPC was changed to maintaining the workability of fresh concrete at the second part of the research. The workability at mixture with dosage of steel fibers of 300 kg/m3 measured by Haegermann cone was around 300 mm. In the framework of grant project GAČR 15-05791S the basic mechanical properties of hardened fine-grained cementitious composite material UHPC at small beams size of 160/40/40 mm and beams size 300/70/70 mm were determined. The aim of the research project was not only the determination of basic mechanical properties for each mixture design but also workability assessment and costs linked with higher amount of the volume fracture of steel fibers.

scholarly journals Developing Geopolymer Concrete Properties by Using Nanomaterials and Steel Fibers

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
E. Rabiaa ◽  
R. A. S. Mohamed ◽  
W. H. Sofi ◽  
Taher A. Tawfik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Sodium Hydroxide ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Steel Fibers ◽  
Hardened Concrete ◽  
Geopolymer Concrete ◽  
Alkaline Activator ◽  
The Impact

This research investigates the simultaneous impact of two different types of steel fibers, nanometakaolin, and nanosilica on the mechanical properties of geopolymer concrete (GPC) mixes. To achieve this aim, different geopolymer concrete mixes were prepared. Firstly, with and without nanomaterials (nanosilica and nanometakaolin) of 0, 2%, 4%, 6%, and 8% from ground granulated blast furnace slag (GGBFS) were used. Secondly, steel fiber (hooked end and crimped) content of (0, 0.5%, 1, and 1.5%) was used. Thirdly, optimum values of nanomaterials with the optimum values of steel fiber were used. Crimped and hooked-end steel fibers were utilized with an aspect ratio of 60 and a length of 30 mm. Geopolymer mixes were manufactured by using a constant percentage of alkaline activator to binder proportion equal to 0.45 with GGBFS cured at ambient conditions. For alkaline activator, sodium hydroxide molar (NaOH) and sodium hydroxide solution (NaOH) were used according to a proportion (Na2SiO3/NaOH) of 2.33. The hardened concrete tests were performed through the usage of splitting tensile strength, flexural, and compressive experiments to determine the impact of steel fibers, nanometakaolin, and nanosilica individually and combined on performance of GPC specimens. The results illustrated that using a mix composed of the optimum steel fibers (1% content) accompanied by an optimum percentage of 6% nanometakaolin or 4% nanosilica demonstrated a significant enhancement in the mechanical properties of GPC specimens compared to all other mixtures. Besides, the impact of using nanomaterials individually was found to be predominant on compressive strength on GPC specimens especially with the usage of the optimum values. However, using nanomaterials individually compared to using the steel fibers individually was found to have approximately the same splitting tensile strength and flexural performance.

Sign in / Sign up

Export Citation Format

Share Document