In-situ micro-tensile investigation of strain rate response along and directions in single crystal nickel

2018 ◽  
Vol 106 ◽  
pp. 129-144 ◽  
Author(s):  
Alan Xu ◽  
Michael Saleh ◽  
Joel Davis ◽  
Lyndon Edwards ◽  
Dhriti Bhattacharyya
Keyword(s):  
Strain Rate ◽  
Single Crystal

Structure of Palladium Single-Crystal Films Prepared by Flash Evaporation onto (001) NaCl Substrates

1970 ◽  
Vol 28 ◽  
pp. 456-457
Author(s):  
L. E. Murr ◽  
G. Wong
Keyword(s):  
Single Crystal ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
High Rate ◽  
Flash Evaporation ◽  
Optimum Load ◽  
Single Crystal Films ◽  
Crystal Films ◽  
A Current

Palladium single-crystal films have been prepared by Matthews in ultra-high vacuum by evaporation onto (001) NaCl substrates cleaved in-situ, and maintained at ∼ 350° C. Murr has also produced large-grained and single-crystal Pd films by high-rate evaporation onto (001) NaCl air-cleaved substrates at 350°C. In the present work, very large (∼ 3cm2), continuous single-crystal films of Pd have been prepared by flash evaporation onto air-cleaved (001) NaCl substrates at temperatures at or below 250°C. Evaporation rates estimated to be ≧ 2000 Å/sec, were obtained by effectively short-circuiting 1 mil tungsten evaporation boats in a self-regulating system which maintained an optimum load current of approximately 90 amperes; corresponding to a current density through the boat of ∼ 4 × 104 amperes/cm2.

Observation of dislocations in dynamically loaded Cu-SiO2

1986 ◽  
Vol 44 ◽  
pp. 424-425
Author(s):  
D. S. Pritchard
Keyword(s):  
Electron Microscope ◽  
Strain Rate ◽  
Single Crystal ◽  
Transmission Electron Microscope ◽  
Volume Fraction ◽  
Screw Dislocations ◽  
Spherical Inclusions ◽  
Transmission Electron ◽  
Crystal Dispersion ◽  
Strain Rate Loading

The effect of varying the strain rate loading conditions in compression on a copper single crystal dispersion-hardened with SiO2 particles has been examined. These particles appear as small spherical inclusions in the copper lattice and have a volume fraction of 0.6%. The structure of representative crystals was examined prior to any testing on a transmission electron microscope (TEM) to determine the nature of the dislocations initially present in the tested crystals. Only a few scattered edge and screw dislocations were viewed in those specimens.

Single Crystal Growth of High-Pressure Phases of Ice and Salt Hydrate Far Below the Original Melting Point by Mixing Alcohol: Crystal Structure Determination of Magnesium Chloride Heptahydrate

2020 ◽  
Author(s):  
Keishiro Yamashita ◽  
Kazuki Komatsu ◽  
Hiroyuki Kagi
Keyword(s):  
Crystal Structure ◽  
High Pressure ◽  
Crystal Growth ◽  
Single Crystal ◽  
Room Temperature ◽  
Growth Technique ◽  
Salt Hydrate ◽  
X Ray

An crystal-growth technique for single crystal x-ray structure analysis of high-pressure forms of hydrogen-bonded crystals is proposed. We used alcohol mixture (methanol: ethanol = 4:1 in volumetric ratio), which is a widely used pressure transmitting medium, inhibiting the nucleation and growth of unwanted crystals. In this paper, two kinds of single crystals which have not been obtained using a conventional experimental technique were obtained using this technique: ice VI at 1.99 GPa and MgCl<sub>2</sub>·7H<sub>2</sub>O at 2.50 GPa at room temperature. Here we first report the crystal structure of MgCl2·7H2O. This technique simultaneously meets the requirement of hydrostaticity for high-pressure experiments and has feasibility for further in-situ measurements.

scholarly journals Hot Workability of 300M Steel Investigated by In Situ and Ex Situ Compression Tests

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 880 ◽  
Author(s):  
Rongchuang Chen ◽  
Haifeng Xiao ◽  
Min Wang ◽  
Jianjun Li
Keyword(s):  
Flow Stress ◽  
Strain Rate ◽  
Hot Working ◽  
Ex Situ ◽  
Lower Strain Rate ◽  
Hot Workability ◽  
Compression Tests ◽  
300M Steel ◽  
Lower Strain

In this work, hot compression experiments of 300M steel were performed at 900–1150 °C and 0.01–10 s−1. The relation of flow stress and microstructure evolution was analyzed. The intriguing finding was that at a lower strain rate (0.01 s−1), the flow stress curves were single-peaked, while at a higher strain rate (10 s−1), no peak occurred. Metallographic observation results revealed the phenomenon was because dynamic recrystallization was more complete at a lower strain rate. In situ compression tests were carried out to compare with the results by ex situ compression tests. Hot working maps representing the influences of strains, strain rates, and temperatures were established. It was found that the power dissipation coefficient was not only related to the recrystallized grain size but was also related to the volume fraction of recrystallized grains. The optimal hot working parameters were suggested. This work provides comprehensive understanding of the hot workability of 300M steel in thermal compression.

scholarly journals Understanding the Strain Path Effect on the Deformed Microstructure of Single Crystal Pure Aluminum

Metals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 1189
Author(s):  
Yingjue Xiong ◽  
Qinmeng Luan ◽  
Kailun Zheng ◽  
Wei Wang ◽  
Jun Jiang
Keyword(s):  
Strain Rate ◽  
Single Crystal ◽  
Strain Path ◽  
Mechanical Response ◽  
Pure Aluminum ◽  
Lattice Rotation ◽  
Softening Behavior ◽  
Theoretical Support ◽  
Commercial Applications ◽  
Electron Back Scattered Diffraction

During plastic deformation, the change of structural states is known to be complicated and indeterminate, even in single crystals. This contributes to some enduring problems like the prediction of deformed texture and the commercial applications of such material. In this work, plane strain compression (PSC) tests were designed and implemented on single crystal pure aluminum to reveal the deformation mechanism. PSC tests were performed at different strain rates under strain control in either one-directional or two-directional compression. The deformed microstructures were analyzed according to the flow curve and the electron back-scattered diffraction (EBSD) mappings. The effects of grain orientation, strain rate, and strain path on the deformation and mechanical response were analyzed. Experimental results revealed that the degree of lattice rotation of one-dimensional compression mildly dependents on cube orientation, but it is profoundly sensitive to the strain rate. For two-dimensional compression, the softening behavior is found to be more pronounced in the case that provides greater dislocations gliding freeness in the first loading. Results presented in this work give new insights into aluminum deformation, which provides theoretical support for forming and manufacturing of aluminum.

Laser damage mechanism and in-situ observation of stacking fault relaxation in β-Ga2O3 single crystal by EFG method

CrystEngComm ◽  
2021 ◽  
Author(s):  
Bo Fu ◽  
Gaohang He ◽  
Wenxiang Mu ◽  
Yang Li ◽  
Boyuan Feng ◽  
...  
Keyword(s):  
Single Crystal ◽  
Light Field ◽  
Damage Mechanism ◽  
Stacking Fault ◽  
High Light ◽  
Laser Damage ◽  
In Situ Observation ◽  
Structure Destruction

We designed an original and effective method to study the laser damage mechanism of β-Ga2O3 single crystal grown by edge-defined film-fed growth (EFG). The structure destruction under high light field...

In-situ X-ray tomography investigation of pore damage effects during a tensile test of a Ni-based single crystal superalloy

2021 ◽  
pp. 111180
Author(s):  
Keli Liu ◽  
Junsheng Wang ◽  
Bing Wang ◽  
Pengcheng Mao ◽  
Yanhong Yang ◽  
...  
Keyword(s):  
Tensile Test ◽  
Single Crystal ◽  
Single Crystal Superalloy ◽  
X Ray

scholarly journals Crack Propagation Behavior of a Ni-Based Single-Crystal Superalloy during In Situ SEM Tensile Test at 1000 °C

Crystals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1047
Author(s):  
Wenxiang Jiang ◽  
Xiaoyi Ren ◽  
Jinghao Zhao ◽  
Jianli Zhou ◽  
Jinyao Ma ◽  
...  
Keyword(s):  
Crack Propagation ◽  
Tensile Test ◽  
Single Crystal ◽  
Crack Propagation Rate ◽  
Propagation Rate ◽  
Single Crystal Superalloy ◽  
Propagation Path ◽  
Propagation Behavior ◽  
Crack Propagation Behavior

An in situ scanning electron microscope (SEM) tensile test for Ni-based single-crystal superalloy was carried out at 1000 °C. The stress displacement was obtained, and the yield strength and tensile strength of the superalloy were 699 MPa and 826 MPa, respectively. The crack propagation process, consisting of Model I crack and crystallographic shearing crack, was determined. More interestingly, the crack propagation path and rate affected by eutectics was directly observed and counted. Results show that the coalescence of the primary crack and second microcrack at the interface of a γ/γ′ matrix and eutectics would make the crack propagation rate increase from 0.3 μm/s to 0.4 μm/s. On the other hand, crack deflection decreased the rate to 0.05 μm/s. Moreover, movement of dislocations in front of the crack was also analyzed to explain the different crack propagation behavior in the superalloy.

On The Optimized Nucleation of Near-Single-Crystal Cvd Diamond Film

1995 ◽  
Vol 416 ◽  
Author(s):  
L. C. Chen ◽  
C. C. Juan ◽  
J. Y. Wu ◽  
K. H. Chen ◽  
J. W. Teng
Keyword(s):  
Single Crystal ◽  
Photoelectron Spectroscopy ◽  
Morphological Evolution ◽  
Present Report ◽  
Ex Situ ◽  
Nucleation Density ◽  
Induced Current ◽  
Current Time ◽  
Single Crystal Diamond

ABSTRACTNear-single-crystal diamond films have been obtained in a number of laboratories recently. The optimization of nucleation density by using a bias-enhanced nucleation (BEN) method is believed to be a critical step. However, the condition of optimized nucleation has never been clearly delineated. In the present report, a novel quantitative technique was established to monitor the nucleation of diamond in-situ. Specifically, the induced current was measured as a function of nucleation time during BEN. The timedependence of induced current was studied under various methane concentrations as well as substrate temperatures. The optimized nucleation condition can be unambiguously determined from the current-time plot. Besides the in-situ current probe, ex-situ x-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) were also used to investigate the chemical and morphological evolution. Characteristic XPS and AFM features of optimized nucleation is discussed.

Sign in / Sign up

Export Citation Format

Share Document