Three-dimensional carbon- and binder-free nickel nanowire arrays as a high-performance and low-cost anode for direct hydrogen peroxide fuel cell

2015 ◽  
Vol 300 ◽  
pp. 147-156 ◽  
Author(s):  
Ke Ye ◽  
Fen Guo ◽  
Yinyi Gao ◽  
Dongming Zhang ◽  
Kui Cheng ◽  
...  
2015 ◽  
Vol 275 ◽  
pp. 831-834 ◽  
Author(s):  
L. An ◽  
T.S. Zhao ◽  
X.L. Zhou ◽  
X.H. Yan ◽  
C.Y. Jung

2016 ◽  
Vol 18 (2) ◽  
pp. 908-915 ◽  
Author(s):  
Bo Wang ◽  
Songmei Li ◽  
Xiaoyu Wu ◽  
Jianhua Liu ◽  
Wenming Tian

Novel three-dimensional (3D) NiMoO4nanowire arrays (NWAs) grown directly onto the surface of macroporous graphene foams (GF) with robust adhesion were synthesizedviaa facile chemical vapor deposition (CVD) and subsequent hydrothermal route.


Author(s):  
Marcel Simsek ◽  
Nongnoot Wongkaew

AbstractNon-enzymatic electrochemical sensors possess superior stability and affordability in comparison to natural enzyme-based counterparts. A large variety of nanomaterials have been introduced as enzyme mimicking with appreciable sensitivity and detection limit for various analytes of which glucose and H2O2 have been mostly investigated. The nanomaterials made from noble metal, non-noble metal, and metal composites, as well as carbon and their derivatives in various architectures, have been extensively proposed over the past years. Three-dimensional (3D) transducers especially realized from the hybrids of carbon nanomaterials either with metal-based nanocatalysts or heteroatom dopants are favorable owing to low cost, good electrical conductivity, and stability. In this critical review, we evaluate the current strategies to create such nanomaterials to serve as non-enzymatic transducers. Laser writing has emerged as a powerful tool for the next generation of devices owing to their low cost and resultant remarkable performance that are highly attractive to non-enzymatic transducers. So far, only few works have been reported, but in the coming years, more and more research on this topic is foreseeable. Graphical abstract


RSC Advances ◽  
2014 ◽  
Vol 4 (110) ◽  
pp. 65031-65034 ◽  
Author(s):  
L. An ◽  
T. S. Zhao ◽  
X. L. Zhou ◽  
L. Wei ◽  
X. H. Yan

We propose to create the cathode potential by introducing a redox couple to the cathode while using hydrogen peroxide to chemically charge the redox ions, which eliminates the mixed potential associated with direct reduction of hydrogen peroxide.


2022 ◽  
Vol 6 (1) ◽  
Author(s):  
Taikyu Kim ◽  
Cheol Hee Choi ◽  
Pilgyu Byeon ◽  
Miso Lee ◽  
Aeran Song ◽  
...  

AbstractAchieving high-performance p-type semiconductors has been considered one of the most challenging tasks for three-dimensional vertically integrated nanoelectronics. Although many candidates have been presented to date, the facile and scalable realization of high-mobility p-channel field-effect transistors (FETs) is still elusive. Here, we report a high-performance p-channel tellurium (Te) FET fabricated through physical vapor deposition at room temperature. A growth route involving Te deposition by sputtering, oxidation and subsequent reduction to an elemental Te film through alumina encapsulation allows the resulting p-channel FET to exhibit a high field-effect mobility of 30.9 cm2 V−1 s−1 and an ION/OFF ratio of 5.8 × 105 with 4-inch wafer-scale integrity on a SiO2/Si substrate. Complementary metal-oxide semiconductor (CMOS) inverters using In-Ga-Zn-O and 4-nm-thick Te channels show a remarkably high gain of ~75.2 and great noise margins at small supply voltage of 3 V. We believe that this low-cost and high-performance Te layer can pave the way for future CMOS technology enabling monolithic three-dimensional integration.


Author(s):  
Jifeng Wang ◽  
Qubo Li ◽  
Norbert Mu¨ller

A mechanical and optimal analyses procedure is developed to assess the stresses and deformations of Novel Wound Composite Axial-Impeller under loading conditions particular to centrifuge. This procedure is based on an analytical method and Finite Element Analysis (FEA, commercial software ANSYS) results. A low-cost, light-weight, high-performance, composite turbomachinery impeller from differently designed patterns will be evaluated. Such impellers can economically enable refrigeration plants using water as a refrigerant (R718). To create different complex patterns of impellers, MATLAB is used for creating the geometry of impellers, and CAD software UG is used to build three-dimensional impeller models. Available loading conditions are: radial body force due to high speed rotation about the cylindrical axis and fluid forces on each blade. Two-dimensional plane stress and three-dimensional stress finite element analysis are carried out using ANSYS to validate these analytical mechanical equations. The von Mises stress is investigated, and maximum stress and Tsai-Wu failure criteria are applied for composite material failure, and they generally show good agreement.


ACS Catalysis ◽  
2018 ◽  
Vol 8 (5) ◽  
pp. 4569-4575 ◽  
Author(s):  
Lingzheng Bu ◽  
Chongyang Tang ◽  
Qi Shao ◽  
Xing Zhu ◽  
Xiaoqing Huang

Sign in / Sign up

Export Citation Format

Share Document