Numerical study of wind turbine wakes over escarpments by a modified delayed detached eddy simulation

2019 ◽  
Vol 191 ◽  
pp. 41-53 ◽  
Author(s):  
Guo-Wei Qian ◽  
Takeshi Ishihara
Keyword(s):  
Wind Turbine ◽  
Numerical Study ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

Numerical study of the flow over the modified simple frigate shape

2020 ◽  
pp. 095441002097775
Author(s):  
Tong Li ◽  
Yibin Wang ◽  
Ning Zhao
Keyword(s):  
Bluff Body ◽  
Recirculation Zone ◽  
Numerical Study ◽  
Reference Value ◽  
Flow Fields ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Simulation Results

The simple frigate shape (SFS) as defined by The Technical Co-operative Program (TTCP), is a simplified model of the frigate, which helps to investigate the basic flow fields of a frigate. In this paper, the flow fields of the different modified SFS models, consisting of a bluff body superstructure and the deck, were numerically studied. A parametric study was conducted by varying both the superstructure length L and width B to investigate the recirculation zone behind the hangar. The size and the position of the recirculation zones were compared between different models. The numerical simulation results show that the size and the location of the recirculation zone are significantly affected by the superstructure length and width. The results obtained by Reynolds-averaged Navier-Stokes method were also compared well with both the time averaged Improved Delayed Detached-Eddy Simulation results and the experimental data. In addition, by varying the model size and inflow velocity, various flow fields were numerically studied, which indicated that the changing of Reynolds number has tiny effect on the variation of the dimensionless size of the recirculation zone. The results in this study have certain reference value for the design of the frigate superstructure.

A numerical study of snow accumulation on the bogies of high-speed trains based on coupling improved delayed detached eddy simulation and discrete phase model

2018 ◽  
Vol 233 (7) ◽  
pp. 715-730 ◽  
Author(s):  
Mingyang Liu ◽  
Jiabin Wang ◽  
Huifen Zhu ◽  
Sinisa Krajnovic ◽  
Guangjun Gao
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Snow Accumulation ◽  
Phase Model ◽  
Detached Eddy Simulation ◽  
Discrete Phase Model ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Flow Mechanisms ◽  
Discrete Phase

A numerical simulation method based on the improved delayed detached eddy simulation coupled with a discrete phase model is used to study the influence of the snow on the performance of bogies of a high-speed train running in snowy weather. The snow particle trajectories, mass of snow packing on the bogie, and thickness of snow accumulation have been analyzed to investigate the flow mechanisms of snow accumulation on different parts of the bogies. The results show that the snow accumulation on the first bogie of the head vehicle is almost the same as that of the second bogie, but the total accumulated snow on the top side of the second bogie is more than 74% higher than that of the first bogie. Among all the components of the bogies, the motors were found to be strongly influenced by the snow accumulation. The underlying flow mechanisms responsible for the snow accumulations are discussed.

LES and Hybrid RANS/LES of a Fundamental Trailing Edge Slot

2014 ◽  
Author(s):  
Elizaveta Ivanova ◽  
Gregory M. Laskowski
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Numerical Study ◽  
Mixing Layer ◽  
Detached Eddy Simulation ◽  
Trailing Edge ◽  
Adiabatic Wall ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This paper presents the results of a numerical study on the predictive capabilities of Large Eddy Simulation (LES) and hybrid RANS/LES methods for heat transfer, mean velocity, and turbulence in a fundamental trailing edge slot. The geometry represents a landless slot (two-dimensional wall jet) with adjustable slot lip thickness. The reference experimental data taken from the publications of Kacker and Whitelaw [1] [2] [3] [4] contains the adiabatic wall effectiveness together with the velocity and the Reynolds-stress profiles for various blowing ratios and slot lip thicknesses. The simulations were conducted at three different lip thickness and several blowing ratio values. The comparison with the experimental data shows a general advantage of LES and hybrid RANS/LES methods against unsteady RANS. The predictive capability of the tested LES models (dynamic ksgs-equation [5] and WALE [6]) was comparable. The Improved Delayed Detached Eddy Simulation (IDDES) hybrid method [7] also shows satisfactory agreement with the experimental data. In addition to the described baseline investigations, the influence of the inlet turbulence boundary conditions and their implication for the initial mixing layer and heat transfer development were studied for both LES and IDDES.

scholarly journals A Dynamic Rotor Vertical-Axis Wind Turbine with a Blade Transitioning Capability

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1446 ◽  
Author(s):  
Elie Antar ◽  
Amne El Cheikh ◽  
Michel Elkhoury
Keyword(s):  
Wind Turbine ◽  
Average Power ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Optimized Design ◽  
Detached Eddy Simulation ◽  
Vertical Axis Wind Turbine ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This work presents an optimized design of a dynamic rotor vertical-axis wind turbine (DR VAWT) which maximizes the operational tip-speed ratio (TSR) range and the average power coefficient (Cp) value while maintaining a low cut-in wind velocity. The DR VAWT is capable of mimicking a Savonius rotor during the start-up phase and transitioning into a Darrieus one with increasing rotor radius at higher TSRs. The design exploits the fact that with increasing rotor radius, the TSR value increases, where the peak power coefficient is attained. A 2.5D improved delayed detached eddy simulation (IDDES) approach was adopted in order to optimize the dynamic rotor design, where results showed that the generated blades’ trajectories can be readily replicated by simple mechanisms in reality. A thorough sensitivity analysis was conducted on the generated optimized blades’ trajectories, where results showed that they were insensitive to values of the Reynolds number. The performance of the DR VAWT turbine with its blades following different trajectories was contrasted with the optimized turbine, where the influence of the blade pitch angle was highlighted. Moreover, a cross comparison between the performance of the proposed design and that of the hybrid Savonius–Darrieus one found in the literature was carefully made. Finally, the effect of airfoil thickness on the performance of the optimized DR VAWT was thoroughly analyzed.

Numerical Study on Vortex-Induced Motions of Semisubmersibles With Three Columns With Different Sections Types

2019 ◽  
Author(s):  
Chenling Tian ◽  
Longfei Xiao ◽  
Mingyue Liu ◽  
Lijun Yang ◽  
Jing Liu
Keyword(s):  
Wind Turbine ◽  
Lift Force ◽  
Transverse Direction ◽  
Numerical Study ◽  
Offshore Structures ◽  
Detached Eddy Simulation ◽  
Fluid Forces ◽  
Eddy Simulation ◽  
Resonance Behavior ◽  
Induced Motion

Abstract Vortex-induced motion (VIM) phenomenon is a great challenge for design and operation of offshore structures subjected to ocean flow. Semi-submersibles with three columns are often applied to the field of wind turbine, suffering VIM motions probably. In recent years, it is showed that many factors have more or less influence on VIM of platforms. A comparison of circular columns with square columns on VIM characteristics of three-column semisubmersibles is carried out using the detached eddy simulation (DES) method via Star-ccm+ software. This paper analyzes motions in the transverse direction and yaw, as well as fluid forces including drag force and fluctuating lift force. The results show that transverse amplitudes of semisubmersible with three square columns are much lower than those of semisubmersible with three circular columns at all incidences. Besides, the authors conclude that the semisubmersible with three square columns do not experience obvious resonance behavior, which is different from the semisubmersible with three circular columns. Besides, galloping phenomenon occurred at large reduced velocities at 0°-incidence for the semisubmersible with three square columns, which is likely not induced by lift force directly. Meanwhile, in these cases, yaw amplitudes are also larger than the others. This may be due to the galloping behavior, which is just a conjecture.

scholarly journals Prediction and measurement of the aerodynamic performance of a wind turbine

2018 ◽  
Vol 240 ◽  
pp. 04001
Author(s):  
Ali Cemal Benim ◽  
Michael Diederich ◽  
Fethi Gül
Keyword(s):  
Wind Turbine ◽  
Transport Model ◽  
Three Dimensional ◽  
Detached Eddy Simulation ◽  
Simulation Framework ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation ◽  
Shear Stress Transport Model ◽  
Flow Turbulence ◽  
Good Agreement

Aerodynamic behavior of a small wind turbine is analyzed, both experimentally and numerically. Mainly, an unsteady three-dimensional formulation is adopted, where the flow turbulence is modelled by an Improved Delayed Detached Eddy Simulation framework, using the four-equation transitional Shear Stress Transport model, as the turbulence model. A quite good agreement between the measurements and calculations is observed.

Aeroacoustics response of wind turbine blade profiles in normal and icing conditions

2018 ◽  
Vol 42 (3) ◽  
pp. 243-251 ◽  
Author(s):  
Edison H Caicedo ◽  
Muhammad S Virk
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Turbine Blade ◽  
Numerical Study ◽  
Turbulence Models ◽  
Wind Turbine Blade ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Eddy Simulation

This article describes a multiphase computational fluid dynamics–based numerical study of the aeroacoustics response of symmetric and asymmetric wind turbine blade profiles in both normal and icing conditions. Three different turbulence models (Reynolds-averaged Navier–Stokes, detached eddy simulation, and large eddy simulation) have been used to make a comparison of numerical results with the experimental data, where a good agreement is found between numerical and experimental results. Detached eddy simulation turbulence model is found suitable for this study. Later, an extended computational fluid dynamics–based aeroacoustics parametric study is carried out for both normal (clean) and iced airfoils, where the results indicate a significant change in sound levels for iced profiles as compared to clean.

Sign in / Sign up

Export Citation Format

Share Document