An average fluid temperature to estimate borehole thermal resistance of ground heat exchanger

2011 ◽  
Vol 36 (6) ◽  
pp. 1880-1885 ◽  
Author(s):  
Ciyuan Du ◽  
Youming Chen
Keyword(s):  
Heat Exchanger ◽  
Thermal Resistance ◽  
Fluid Temperature ◽  
Ground Heat Exchanger ◽  
Borehole Thermal Resistance

scholarly journals Borehole Thermal Analysis for a Closed Loop Vertical U-Tube DX Ground Heat Exchanger

2021 ◽  
Vol 8 (4) ◽  
pp. 501-509
Author(s):  
Ali H. Tarrad
Keyword(s):  
Heat Exchanger ◽  
Thermal Resistance ◽  
Thermal Design ◽  
Ground Heat Exchanger ◽  
Total Thermal Resistance ◽  
Steady State Condition ◽  
Tube Heat Exchanger ◽  
Cooling Unit ◽  
Geometry Configuration ◽  
Borehole Thermal Resistance

The borehole geometry configuration and its sizing represent great challenges to the thermal equipment designer in the field of geothermal energy source. The present work represents a piece in that direction to avoid elaborate mathematical and computation schemes constraints for the preliminary design of the U-tube ground heat exchanger operates under a steady-state condition. A correlation was built for the prediction of the borehole thermal resistance. The U-tube diameter, leg spacing, borehole diameter, and the offset configuration with respect to the center of the borehole were introduced in the present correlation. An equivalent tube formula and borehole configuration were postulated to possess the same grout volume as the original loop. A variety of geometrical configurations were tested at different U-tube and borehole sizes. The predicted total thermal resistance of the borehole was implemented into the thermal design of the (DX) ground condenser to sizing the borehole U-tube heat exchanger. A hypothetical cooling unit of (1) ton of refrigeration that circulates R410A refrigerant was chosen for the verification of the present model outcomes. The predicted thermal resistance revealed an excellent agreement with other previously published work in this category.

scholarly journals Analysis on Thermal Performance of Ground Heat Exchanger According to Design Type Based on Thermal Response Test

Energies ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 651 ◽  
Author(s):  
Sang Bae ◽  
Yujin Nam ◽  
Jong Choi ◽  
Kwang Lee ◽  
Jae Choi
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchanger ◽  
Heat Exchange ◽  
Thermal Resistance ◽  
Heat Pump ◽  
Thermal Performance ◽  
Thermal Response ◽  
Ground Heat Exchanger ◽  
Thermal Response Test ◽  
Borehole Thermal Resistance

A ground source heat pump (GSHP) system has higher performance than air source heat pump system due to the use of more efficient ground heat source. However, the GSHP system performance depends on ground thermal properties and groundwater conditions. There are many studies on the improvement of GSHP system by developing ground heat exchanger (GHX) and heat exchange method. Several studies have suggested methods to improve heat exchange rate for the development of GHX. However, few real-scale experimental studies have quantitatively analyzed their performance using the same ground conditions. Therefore, the objective of this study was to evaluate the thermal performance of various pipe types of GHX by the thermal response test (TRT) under the same field and test conditions. Four kinds of GHX (HDPE type, HDPE-nano type, spiral fin type, and coaxial type) were constructed in the same site. Inlet and outlet temperatures of GHXs and effective thermal conductivity were measured through the TRT. In addition, the borehole thermal resistance was calculated to comparatively analyze the correlation of the heat exchange performance with each GHX. Result of the TRT revealed that averages effective thermal conductivities of HDPE type, HDPE-nano, spiral fin type, and coaxial type GHX were 2.25 W/m·K, 2.34 W/m·K, 2.55 W/m·K, and 2.16 W/m·K, respectively. In the result, it was found that the average borehole thermal resistance can be an important factor in TRT, but the effect of increased thermal conductivity of pipe material itself was not significant.

Comparison of Borehole Thermal Resistance Values of Ground Heat Exchanger Obtained by Several Methods

2013 ◽  
Vol 732-733 ◽  
pp. 103-108 ◽  
Author(s):  
Han Byul Kang ◽  
Seok Yoon ◽  
Gyu Hyun Go ◽  
Seung Rae Lee
Keyword(s):  
Heat Exchanger ◽  
Thermal Resistance ◽  
Heat Pump ◽  
Heating System ◽  
Geothermal System ◽  
Ground Heat Exchanger ◽  
Ubiquitous System ◽  
Borehole Thermal Resistance ◽  
Quantity Of Heat ◽  
Emission Of Greenhouse Gases

The Ground-Coupled or Source Heat Pump (GCHP/GSHP) system is increasingly being considered as an alternative to traditional cooling/heating system because it can reduce the emission of greenhouse gases. The GCHP/GSHP system uses sustainable ground temperature to emit heat during the summer and to extract heat during the winter. It is a ubiquitous system because it can be used at any time or place and semi-permanent energy. The geothermal system is composed of Ground Heat Exchanger (GHE), heat pump and load facilities. The GHE is embedded in a borehole, which is made up of GHE and grout. The borehole thermal resistance is the most important parameter in designing the geothermal system because it shows the quantity of heat transfer in the borehole. There are many methods to estimate the borehole thermal resistance. Thermal Performance Tests (TPTs) were conducted to directly measure the borehole thermal resistance of several kinds of GHEs. Then the experiment results and analytical results were compared in order to select the most accurate methods to evaluate the borehole thermal resistance.

scholarly journals Evaluation of Borehole Thermal Resistance in Ground Heat Exchanger

2013 ◽  
Vol 29 (10) ◽  
pp. 49-56 ◽  
Author(s):  
Seok Yoon ◽  
Seung-Rae Lee ◽  
Han-Byul Kang ◽  
Gyu-Hyun Go ◽  
Min-Jun Kim ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Thermal Resistance ◽  
Ground Heat Exchanger ◽  
Borehole Thermal Resistance

scholarly journals Borehole Resistance and Heat Conduction Around Vertical Ground Heat Exchangers

2012 ◽  
Vol 6 (1) ◽  
pp. 32-40 ◽  
Author(s):  
Zoi Sagia ◽  
Athina Stegou ◽  
Constantinos Rakopoulos
Keyword(s):  
Heat Conduction ◽  
Heat Exchanger ◽  
Thermal Resistance ◽  
Heat Exchangers ◽  
Borehole Diameter ◽  
Working Fluid ◽  
Geometrical Parameters ◽  
Conductive Heat ◽  
Ground Heat Exchanger ◽  
Borehole Thermal Resistance

Borehole thermal resistance in Ground Heat Exchanger (GHE) installations is affected by several parameters such as geometrical attributes of heat exchanger in the borehole, pipes' characteristics and grout’s thermal conductivity. A study is carried out to compare the values computed by Ground Loop Design (GLD) Software, GLD 2009, with three ana-lytical solutions for U-shaped tubes. The analysis is focused on dimensionless ratios of borehole geometrical parameters (borehole diameter to outside pipe diameter and shank spacing to borehole diameter) and pipes according to Standard Di-mension Ratio (SDR) and on eight common grouts. Finally, the effect of heat conduction in the borehole is examined by means of finite element analysis by Heat Transfer Module of COMSOL Multiphysics. A two-dimensional (2-D) steady-state simulation is done assuming working fluid temperatures for winter and summer conditions and typical Greek undis-turbed ground temperature in a field of four ground vertical U-tube heat exchangers surrounded by infinite ground. The temperature profile is presented and the total conductive heat flux from the pipe to the borehole wall per meter of length of ground heat exchanger is computed for pipes SDR11 (the outside diameter of the pipe is 11 times the thickness of its wall), SDR9 and SDR17 for summer working conditions and three different configurations. It is attempted to reach to comparative results for borehole thermal resistance value through different types of analysis, having considered the major factors that affect it and giving trends for the influence of each factor to the magnitude of its value.

scholarly journals Effects of the Circuit Arrangement on the Thermal Performance of Double U-Tube Ground Heat Exchangers

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3275
Author(s):  
Aminhossein Jahanbin ◽  
Giovanni Semprini ◽  
Andrea Natale Impiombato ◽  
Cesare Biserni ◽  
Eugenia Rossi di Schio
Keyword(s):  
Thermal Resistance ◽  
Thermal Performance ◽  
Numerical Code ◽  
Geometrical Parameters ◽  
Fluid Temperature ◽  
The Finite Element Method ◽  
Ground Heat Exchangers ◽  
Borehole Thermal Resistance ◽  
The Impact ◽  
Circuit Configuration

Given that the issue of variations in geometrical parameters of the borehole heat exchanger (BHE) revolves around the phenomenon of thermal resistance, a thorough understanding of these parameters is beneficial in enhancing thermal performance of BHEs. The present study seeks to identify relative changes in the thermal performance of double U-tube BHEs triggered by alterations in circuit arrangements, as well as the shank spacing and the borehole length. The thermal performance of double U-tube BHEs with different configurations is comprehensively analyzed through a 3D transient numerical code developed by means of the finite element method. The sensitivity of each circuit configuration in terms of the thermal performance to variations of the borehole length and shank spacing is investigated. The impact of the thermal interference between flowing legs, namely thermal short-circuiting, on parameters affecting the borehole thermal resistance is addressed. Furthermore, the energy exchange characteristics for different circuit configurations are quantified by introducing the thermal effectiveness coefficient. The results indicate that the borehole length is more influential than shank spacing in increasing the discrepancy between thermal performances of different circuit configurations. It is shown that deviation of the averaged-over-the-depth mean fluid temperature from the arithmetic mean of the inlet and outlet temperatures is more critical for lower shank spacings and higher borehole lengths.

scholarly journals An Enhanced Vertical Ground Heat Exchanger Model for Whole-Building Energy Simulation

Energies ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 4058
Author(s):  
Matt S. Mitchell ◽  
Jeffrey D. Spitler
Keyword(s):  
Heat Exchanger ◽  
Temperature Response ◽  
Building Energy ◽  
Energy Simulation ◽  
Building Energy Simulation ◽  
Response Factor ◽  
Fluid Temperature ◽  
Ground Heat Exchanger ◽  
Vertical Ground ◽  
Whole Building Energy Simulation

This paper presents an enhanced vertical ground heat exchanger (GHE) model for whole-building energy simulation (WBES). WBES programs generally have computational constraints that affect the development and implementation of component simulation sub-models. WBES programs require models that execute quickly and efficiently due to how the programs are utilized by design engineers. WBES programs also require models to be formulated so their performance can be determined from boundary conditions set by upstream components and environmental conditions. The GHE model developed during this work utilizes an existing response factor model and extends its capabilities to accurately and robustly simulate at timesteps that are shorter than the GHE transit time. This was accomplished by developing a simplified dynamic borehole model and then exercising that model to generate exiting fluid temperature response factors. This approach blends numerical and analytical modeling methods. The existing response factor models are then extended to incorporate the exiting fluid temperature response factor to provide a better estimate of the GHE exiting fluid temperature at short simulation timesteps.

Effect of depth and fluid flow rate on estimate for borehole thermal resistance of single U-pipe borehole heat exchanger

2020 ◽  
Vol 147 ◽  
pp. 2399-2408 ◽  
Author(s):  
Changxing Zhang ◽  
Xinjie Wang ◽  
Pengkun Sun ◽  
Xiangqiang Kong ◽  
Shicai Sun
Keyword(s):  
Fluid Flow ◽  
Heat Exchanger ◽  
Thermal Resistance ◽  
Flow Rate ◽  
Fluid Flow Rate ◽  
Borehole Heat Exchanger ◽  
Borehole Thermal Resistance
Sign in / Sign up

Export Citation Format

Share Document