Compliant Foil Bearings Technology and Their Application to High Speed Turbomachinery

1993 ◽  
pp. 559-575 ◽  
Author(s):  
H. Heshmat ◽  
P. Hermel
Keyword(s):  
High Speed ◽  
Foil Bearings

Rotordynamic Performance of a Rotor Supported on Bump Type Foil Gas Bearings: Experiments and Predictions

2006 ◽  
Vol 129 (3) ◽  
pp. 850-857 ◽  
Author(s):  
Luis San Andrés ◽  
Dario Rubio ◽  
Tae Ho Kim
Keyword(s):  
High Speed ◽  
Critical Speed ◽  
Load Capacity ◽  
Test System ◽  
Foil Bearings ◽  
Rotor Imbalance ◽  
Synchronous Motion ◽  
Damping Characteristics ◽  
Rotor Surface ◽  
Stiffness And Damping

Gas foil bearings (GFBs) satisfy the requirements for oil-free turbomachinery, i.e., simple construction and ensuring low drag friction and reliable high speed operation. However, GFBs have a limited load capacity and minimal damping, as well as frequency and amplitude dependent stiffness and damping characteristics. This paper provides experimental results of the rotordynamic performance of a small rotor supported on two bump-type GFBs of length and diameter equal to 38.10mm. Coast down rotor responses from 25krpm to rest are recorded for various imbalance conditions and increasing air feed pressures. The peak amplitudes of rotor synchronous motion at the system critical speed are not proportional to the imbalance introduced. Furthermore, for the largest imbalance, the test system shows subsynchronous motions from 20.5krpm to 15krpm with a whirl frequency at ∼50% of shaft speed. Rotor imbalance exacerbates the severity of subsynchronous motions, thus denoting a forced nonlinearity in the GFBs. The rotor dynamic analysis with calculated GFB force coefficients predicts a critical speed at 8.5krpm, as in the experiments; and importantly enough, unstable operation in the same speed range as the test results for the largest imbalance. Predicted imbalance responses do not agree with the rotor measurements while crossing the critical speed, except for the lowest imbalance case. Gas pressurization through the bearings’ side ameliorates rotor subsynchronous motions and reduces the peak amplitudes at the critical speed. Posttest inspection reveal wear spots on the top foils and rotor surface.

An experimental investigation of a microturbine simulated rotor supported on multileaf gas foil bearings with backing bump foils

2017 ◽  
Vol 232 (9) ◽  
pp. 1169-1180 ◽  
Author(s):  
Bo Zhang ◽  
Shemiao Qi ◽  
Sheng Feng ◽  
Haipeng Geng ◽  
Yanhua Sun ◽  
...  
Keyword(s):  
High Speed ◽  
Preliminary Test ◽  
Journal Bearings ◽  
Rotating Machinery ◽  
System Stability ◽  
Test Rig ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Simulated System ◽  
First Time

Two multileaf gas foil journal bearings with backing bump foils and one set of gas foil thrust bearings were designed, fabricated, and used in a 100 kW class microturbine simulated rotor system to ensure stability of the system. Meanwhile, a preliminary test rig had been built to verify the simulated system stability. The rotor synchronous and subsynchronous responses were well controlled by using of the gas foil bearings. It is on the multileaf gas foil bearings with backing bump foils that the test was conducted and verified for the first time in open literatures. The success in the experiments shows that the design and fabrication of the rotor and the gas foil bearings can provide a useful guide to the development of the advanced high speed rotating machinery.

Analysis of high speed permanent magnet synchronous motor rotor supported by air foil bearings

2019 ◽  
Vol 59 (2) ◽  
pp. 755-764
Author(s):  
Hao Lin ◽  
Haipeng Geng ◽  
Tingchen Du ◽  
Xiangming Xu ◽  
Yanyan Zhang ◽  
...  
Keyword(s):  
Permanent Magnet ◽  
High Speed ◽  
Permanent Magnet Synchronous Motor ◽  
Synchronous Motor ◽  
Foil Bearings

Rotordynamics Performance of Hybrid Foil Bearing Under Forced Vibration Input

2017 ◽  
Author(s):  
Daejong Kim ◽  
Brian Nicholson ◽  
Lewis Rosado ◽  
Garry Givan
Keyword(s):  
Impulse Response ◽  
High Speed ◽  
Load Capacity ◽  
Supply System ◽  
Forced Response ◽  
Experimental Results ◽  
Lateral Acceleration ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Gas Supply

Foil bearings are one type of hydrodynamic air/gas bearings but with a compliant bearing surface supported by structural material that provides stiffness and damping to the bearing. The hybrid foil bearing (HFB) in this paper is a combination of a traditional hydrodynamic foil bearing with externally-pressurized air/gas supply system to enhance load capacity during the start and to improve thermal stability of the bearing. The HFB is more suitable for relatively large and heavy rotors where rotor weight is comparable to the load capacity of the bearing at full speed and extra air/gas supply system is not a major added cost. With 4,448N∼22,240N thrust class turbine aircraft engines in mind, the test rotor is supported by HFB in one end and duplex rolling element bearings in the other end. This paper presents experimental work on HFB with diameter of 102mm performed at the US Air force Research Laboratory. Experimental works include: measurement of impulse response of the bearing to the external load corresponding to rotor’s lateral acceleration of 5.55g, forced response to external subsynchronous excitation, and high speed imbalance response. A non-linear rotordynamic simulation model was also applied to predict the impulse response and forced subsynchronous response. The simulation results agree well with experimental results. Based on the experimental results and subsequent simulations, an improved HFB design is also suggested for higher impulse load capability up to 10g and rotordynamics stability up to 30,000rpm under subsynchronous excitation.

Rotordynamic Performance of a Shaft With Large Overhung Mass Supported by Foil Bearings

2016 ◽  
Vol 139 (4) ◽  
Author(s):  
Nguyen LaTray ◽  
Daejong Kim
Keyword(s):  
High Speed ◽  
Foil Bearings ◽  
Speed Test ◽  
Foil Bearing ◽  
Stable Conditions ◽  
Bending Mode ◽  
Mode Vibration ◽  
Lift Off ◽  
Compact Design ◽  
Bearing System

This work presents the theoretical and experimental rotordynamic evaluations of a rotor–air foil bearing (AFB) system supporting a large overhung mass for high-speed application. The proposed system highlights the compact design of a single shaft rotor configuration with turbomachine components arranged on one side of the bearing span. In this work, low-speed tests up to 45 krpm are performed to measure lift-off speed and to check bearing manufacturing quality. Rotordynamic performance at high speeds is evaluated both analytically and experimentally. In the analytical approach, simulated imbalance responses are studied using both rigid and flexible shaft models with bearing forces calculated from the transient Reynolds equation along with the rotor motion. The simulation predicts that the system experiences small synchronous rigid mode vibration at 20 krpm and bending mode at 200 krpm. A high-speed test rig is designed to experimentally evaluate the rotor–air foil bearing system. The high-speed tests are operated up to 160 krpm. The vibration spectrum indicates that the rotor–air foil bearing system operates under stable conditions. The experimental waterfall plots also show very small subsynchronous vibrations with frequency locked to the system natural frequency. Overall, this work demonstrates potential capability of the air foil bearings in supporting a shaft with a large overhung mass at high speed.

Influence of geometric parameters on the bump foil bearing performance

2019 ◽  
Vol 234 (7) ◽  
pp. 1017-1026
Author(s):  
Sadanand Kulkarni ◽  
Soumendu Jana
Keyword(s):  
Carrying Capacity ◽  
High Speed ◽  
System Development ◽  
Load Capacity ◽  
Radial Clearance ◽  
Load Carrying Capacity ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Load Carrying ◽  
Lift Off

High-speed rotating system development has drawn considerable attention of the researchers, in the recent past. Foil bearings are one of the major contenders for such applications, particularly for high speed and low load rotating systems. In foil bearings, process fluid or air is used as the working medium and no additional lubricant is required. It is known from the published literature that the load capacity of foil bearings depend on the operating speed, viscosity of the medium, clearance, and stiffness of the foil apart from the geometric dimensions of the bearing. In case of foil bearing with given dimensions, clearance governs the magnitude of pressure developed, whereas stiffness dictates the change in radial clearance under the generated pressure. This article deals with the effect of stiffness, clearance, and its interaction on the bump foil bearings load-carrying capacity. For this study, four sets of foil bearings of the same geometry with two levels of stiffness and clearance values are fabricated. Experiments are carried out following two factor-two level factorial design approach under constant load and in each case, the lift-off speed is measured. The experimental output is analyzed using statistical techniques to evaluate the influence of parameters under consideration. The results indicate that clearance has the maximum influence on the lift-off speed/ load-carrying capacity, followed by interaction effect and stiffness. A regression model is developed based on the experimental values and model is validated using error analysis technique.

scholarly journals Rotor dynamic experimental investigation of an ultra-high-speed permanent magnet synchronous motor supported on a three-pad bidirectional gas foil bearing

2019 ◽  
Vol 11 (9) ◽  
pp. 168781401987536
Author(s):  
Wenjie Cheng ◽  
Zhikai Deng ◽  
Ling Xiao ◽  
Bin Zhong ◽  
Wenbo Duan
Keyword(s):  
Permanent Magnet ◽  
High Speed ◽  
Permanent Magnet Synchronous Motor ◽  
Synchronous Motor ◽  
Rotor System ◽  
Permanent Magnet Motors ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Ultra High Speed ◽  
Rotor Dynamic

With a 10-kW, 120,000-r/min, ultra-high-speed permanent magnet synchronous motor taken as a prototype, experimental research is conducted on the rotor dynamic behaviours of a three-pad bidirectional gas foil bearing high-speed motor rotor system. Load-carrying properties of the three-pad bidirectional gas foil bearing are analysed, and natural frequencies of conical and parallel whirling modes of the elastically supported rotor are calculated based on an appropriate simplification to the stiffness and damping coefficients of the gas foil bearings. The prototype passes through a 90,000-r/min coast-down experiment. Experiments show that there are violent subsynchronous whirling motions that are evoked by the gas foil bearing–rotor system itself. The cause of shaft orbit drift is analysed, and the corresponding solution is put forward. The theoretical analysis and experimental results can offer a useful reference to the bearing–rotor system design of ultra-high-speed permanent magnet motors and its subsequent dynamic analysis.

Vibration Mitigation of Rotors Suspended on Low-Cost Hybrid Gas Foil Bearing

2019 ◽  
Author(s):  
Kamal Kumar Basumatary ◽  
Karuna Kalita ◽  
Sashindra K. Kakoty ◽  
Seamus D. Garvey
Keyword(s):  
High Speed ◽  
Low Cost ◽  
Current Source ◽  
Magnetic Bearing ◽  
Active Magnetic Bearing ◽  
Electromagnetic Actuators ◽  
Manufacturing Method ◽  
Foil Bearings ◽  
Foil Bearing ◽  
Small Series

Abstract The hybrid Gas Foil Bearings combining the Gas Foil Bearing and Active Magnetic Bearing is a possibility for application in high-speed turbomachinery and a few developments have been made in this context. As such, the cost of conventional Gas Foil Bearing increases due to its requirement of precise manufacturing method and the coating material for the top foil and bump foil. In case of Active Magnetic Bearing, the normal electrical arrangement includes a multiplicity of independently controlled current sources usually at least four drives per bearing which increases its cost. Therefore, the hybrid Gas Foil Bearing will have much higher cost. In this work, a new electrical arrangement for the electromagnetic actuators of the hybrid Gas Foil Bearing has been proposed. The new arrangement requires only two drives per bearing and the bias current has been provided (in the same set of windings) through a simple rectifier with small series choke and shunt capacitor. As the number of drives required is less, the proposed bearing will have low cost. Implementing the new approach, the force vectors are achieved using only two current-source drives whereas the usual conventional arrangement requires four such drives. Numerical simulations are performed to explore the capabilities of the low cost bearing.

Development of Foil Thrust Bearings with Simple Structure for Micro Turbines

2011 ◽  
Vol 368-373 ◽  
pp. 1392-1395 ◽  
Author(s):  
Quan Zhou ◽  
Yu Hou ◽  
Ru Gang Chen
Keyword(s):  
High Speed ◽  
Simple Structure ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Complicated Structure ◽  
Thrust Bearings ◽  
Foil Bearings ◽  
Rotational Systems ◽  
Micro Turbine ◽  
Foil Thrust Bearing

Because of the low power loss and high stability, foil bearings are suitable lubrication components for high speed rotational systems. At present, the foil bearings used in actual applications almost have complicated structure and are hard to manufacture. In this paper, two kinds of foil thrust bearings with simple structure are presented. Configurations of these two foil thrust bearings are introduced; meanwhile, the load capacity and running stability are also tested in a high speed micro turbine. It is shown that viscoelastic supported foil thrust bearing has higher load capacity and hemisphere convex dots supported foil thrust bearing is more stable in high speed operational condition.

Foil Bearings Makes Oil-Free Turbocharger Possible

2005 ◽  
Author(s):  
Crystal A. Heshmat ◽  
Hooshang Heshmat ◽  
Mark J. Valco ◽  
Kevin C. Radil ◽  
Christopher Della Corte
Keyword(s):  
High Speed ◽  
Solid Lubricant ◽  
Load Capacity ◽  
Maximum Load ◽  
Solid Lubricant Coating ◽  
Foil Bearings ◽  
Wide Range ◽  
Rotor Bearing ◽  
Component Development ◽  
Bearing System

This paper describes an oil-free, 150 Hp turbocharger that was successfully operated with compliant foil bearings in a range of pitch and roll angles, including vertical operation, thereby demonstrating its viability for aircraft applications. On a gas test stand the turbocharger was operated to 120,000 rpm, under extreme conditions. In addition, the compliant foil bearing-supported turbocharger successfully tolerated shock and vibration of 40 g. Advanced technologies have been applied to the second generation of this turbocharger, shown in Figure 1, including self acting, compliant foil hydrodynamic air bearings with advanced coatings capable, of operation above 815 °C (1500°F). Journal foil bearings with maximum load capacity up to 670 kPa (97 psi) were used in conjunction with thrust foil bearings capable of maximum loads to 570 kPa (83 psi). Bearing component development tests demonstrated 30,000 start stop cycles at 815 °C (1500°F) with a newly developed, solid lubricant coating, KOROLON™. KOROLON™ exhibits a coefficient of friction of less than 0.1 at a wide range of temperatures. Current-designed foil bearings with KOROLON™ have immensely decreased turbolag, allowing acceleration from rest to over 100,000 rpm in less than 2 seconds. Advanced bearing stiffness maintained rotor total axial end-to-end motion within 100 microns (0.004 inch). Total radial static and dynamic motion was controlled within 25 microns (0.001 inch). Development of this high speed turbomachine included bearing and solid lubricant component development tests, rotor-bearing dynamic simulator qualification and gas stand tests of the assembled turbocharger. Gas stand and simulator test results revealed stable bearing temperatures, low rotor vibrations, good shock tolerance and the ability of the rotor bearing system to sustain overspeed conditions beyond 120,000 rpm. This combination of component and integrated rotor-bearing system technology addresses many of the issues associated with application of compliant foil bearings to industrial compressors, blowers, and gas turbine engines, overcoming many of the inherently show-stopping and debilitating features of rolling element bearings, i.e., speed and temperature limitations.

Sign in / Sign up

Export Citation Format

Share Document