Three-dimensional instability of the flow over a forward-facing step

2012 ◽  
Vol 695 ◽  
pp. 390-404 ◽  
Author(s):  
Daniel Lanzerstorfer ◽  
Hendrik C. Kuhlmann
Keyword(s):  
Stability Boundary ◽  
Temporal Stability ◽  
Three Dimensional ◽  
Plane Channel ◽  
Separated Flow ◽  
Critical Mode ◽  
Flow Deceleration ◽  
Forward Facing Step ◽  
Adjoint Analysis ◽  
The Stability

AbstractThe global, temporal stability of the two-dimensional, incompressible flow over a forward-facing step in a plane channel is investigated numerically. The geometry is varied systematically covering constriction ratios (step-to-inlet height) from 0.23 to 0.965. A three-dimensional linear stability analysis shows that the stability boundary is a smooth continuous function of the constriction ratio. If the critical Reynolds and wavenumbers are scaled appropriately, they approach a linear asymptotic behaviour for large step heights. The critical mode is found to be stationary and confined to the region of separated flow downstream of the step for all constriction ratios. An energy-transfer analysis reveals that the basic flow becomes unstable due to a combined effect involving lift-up and flow deceleration, leading to a critical mode exhibiting steady streaks. Moreover, the receptivity of the flow to initial as well as to structural perturbations is studied by means of an adjoint analysis.

Experiments on the stability of sinusoidal flow over a circular cylinder

2002 ◽  
Vol 457 ◽  
pp. 157-180 ◽  
Author(s):  
TURGUT SARPKAYA
Keyword(s):  
Stokes Flow ◽  
Coherent Structures ◽  
High Speed ◽  
Three Dimensional ◽  
Separated Flow ◽  
Circular Cylinders ◽  
Centrifugal Forces ◽  
Complex Interactions ◽  
Sinusoidal Flow ◽  
The Stability

The instabilities in a sinusoidally oscillating non-separated flow over smooth circular cylinders in the range of Keulegan–Carpenter numbers, K, from about 0.02 to 1 and Stokes numbers, β, from about 103 to 1.4 × 106 have been observed from inception to chaos using several high-speed imagers and laser-induced fluorescence. The instabilities ranged from small quasi-coherent structures, as in Stokes flow over a flat wall (Sarpkaya 1993), to three-dimensional spanwise perturbations because of the centrifugal forces induced by the curvature of the boundary layer (Taylor–Görtler instability). These gave rise to streamwise-oriented counter-rotating vortices or mushroom-shaped coherent structures as K approached the Kh values theoretically predicted by Hall (1984). Further increases in K for a given β led first to complex interactions between the coherent structures and then to chaotic motion. The mapping of the observations led to the delineation of four states of flow in the (K, β)-plane: stable, marginal, unstable, and chaotic.

scholarly journals Effects of the Control Parameters on the Stability of a Laminar Boundary Layer on a Porous Flat Plate

2021 ◽  
Vol 26 (4) ◽  
pp. 113-127
Author(s):  
T.F. Lihonou ◽  
A.V. Monwanou ◽  
C.H. Miwadinou ◽  
J.B. Chabi Orou
Keyword(s):  
Boundary Layer ◽  
Numerical Solutions ◽  
Temporal Stability ◽  
Three Dimensional ◽  
Darcy Number ◽  
Basic Flow ◽  
Marginal Stability ◽  
Stability Diagrams ◽  
Plane Plate ◽  
The Stability

Abstract This work is devoted to the analysis of the linear temporal stability of a laminar dynamic boundary layer on a horizontal porous plane plate. The basic flow is assumed to be laminar and two-dimensional. The basic flow velocity profiles are obtained by numerically solving the Blasius equation using the Runge-Kutta method. The perturbations of these basic solutions are expressed in the form of three-dimensional Tollmien-Schlichting waves. The formulation of the stability problem leads to the Orr-Sommerfeld equation modified by the permeability parameter (Darcy number) and the small Reynolds number. This equation is given in a general form which can be applied to the Chebyshev domain and the boundary layer domain and solved numerically using the Chebyshev spectral collocation method. The marginal stability diagrams, the critical Reynolds numbers and the eigenvalue spectra are obtained for different values of the parameters which have modified the stability equation. Numerical solutions indicate the importance of the effect of these parameters on the flow stability characteristics.

Stability of thermoviscous Hele-Shaw flow

1996 ◽  
Vol 308 ◽  
pp. 111-128 ◽  
Author(s):  
S. J. S. Morris
Keyword(s):  
Variable Viscosity ◽  
Temporal Stability ◽  
Three Dimensional ◽  
Channel Length ◽  
Base Flow ◽  
Plane Flow ◽  
Entry Length ◽  
Specific Heats ◽  
The Stability ◽  
Long Channel

Viscous fingering can occur as a three-dimensional disturbance to plane flow of a hot thermoviscous liquid in a Hele-Shaw cell with cold isothermal walls. This work assumes the principle of exchange of stabilities, and uses a temporal stability analysis to find the critical viscosity ratio and finger spacing as functions of channel length, Lc. Viscous heating is taken as negligible, so the liquid cools with distance (x) downstream. Because the base flow is spatially developing, the disturbance equations are not fully separable. They admit, however, an exact solution for a liquid whose viscosity and specific heats are arbitrary functions of temperature. This solution describes the neutral disturbances in terms of the base flow and an amplitude, A(x). The stability of a given (computed) base flow is determined by solving an eigenvalue problem for A(x), and the critical finger spacing. The theory is illustrated by using it to map the instability for variable-viscosity flow with constant specific heat. Two fingering modes are predicted, one being a turning-point instability. The preferred mode depends on Lc. Finger spacing is comparable with the thermal entry length in a long channel, and is even larger in short channels. When applied to magmatic systems, the results suggest that fingering will occur on geological scales only if the system is about freeze.

Nonlinear Dynamics of a Rigid Block on a Rigid Base

1996 ◽  
Vol 63 (1) ◽  
pp. 55-61 ◽  
Author(s):  
R. N. Iyengar ◽  
D. Roy
Keyword(s):  
Stability Boundary ◽  
Three Dimensional ◽  
Melnikov Function ◽  
Rigid Base ◽  
Rigid Block ◽  
Stable And Unstable Manifolds ◽  
Melnikov Functions ◽  
Unstable Manifolds ◽  
Simulation Results ◽  
The Stability

The planar rocking of a prismatic rectangular rigid block about either of its corners is considered. The problem of homoclinic intersections of the stable and unstable manifolds of the perturbed separatrix is addressed to and the corresponding Melnikov functions are derived. Inclusion of the vertical forcing in the Hamiltonian permits the construction of a three-dimensional separatrix. The corresponding modified Melnikov function of Wiggins for homoclinic intersections is derived. Further, the 1-period symmetric orbits are predicted analytically using the method of averaging and compared with the simulation results. The stability boundary for such orbits is also established.

Implications of Person Fluctuation for the Stability and Validity of Test Scores

Methodology ◽  
2006 ◽  
Vol 2 (4) ◽  
pp. 142-148 ◽  
Author(s):  
Pere J. Ferrando
Keyword(s):  
Item Response ◽  
Test Scores ◽  
Temporal Stability ◽  
Person Fit ◽  
Item Parameters ◽  
Individual Trait ◽  
The Stability ◽  
The Individual ◽  
Different Levels ◽  
Fluctuation Model

In the IRT person-fluctuation model, the individual trait levels fluctuate within a single test administration whereas the items have fixed locations. This article studies the relations between the person and item parameters of this model and two central properties of item and test scores: temporal stability and external validity. For temporal stability, formulas are derived for predicting and interpreting item response changes in a test-retest situation on the basis of the individual fluctuations. As for validity, formulas are derived for obtaining disattenuated estimates and for predicting changes in validity in groups with different levels of fluctuation. These latter formulas are related to previous research in the person-fit domain. The results obtained and the relations discussed are illustrated with an empirical example.

A Liquid Metal Flow Between Two Coaxial Cylinders System

2019 ◽  
Vol 11 (1) ◽  
pp. 79-86
Author(s):  
Abdelkrim Merah ◽  
Ridha Kelaiaia ◽  
Faiza Mokhtari
Keyword(s):  
Couette Flow ◽  
Metal Flow ◽  
Three Dimensional ◽  
Liquid Sodium ◽  
Taylor Vortex ◽  
Turbulent Regime ◽  
Coaxial Cylinders ◽  
Concentric Cylinders ◽  
Ideal Tool ◽  
The Stability

Abstract The Taylor-Couette flow between two rotating coaxial cylinders remains an ideal tool for understanding the mechanism of the transition from laminar to turbulent regime in rotating flow for the scientific community. We present for different Taylor numbers a set of three-dimensional numerical investigations of the stability and transition from Couette flow to Taylor vortex regime of a viscous incompressible fluid (liquid sodium) between two concentric cylinders with the inner one rotating and the outer one at rest. We seek the onset of the first instability and we compare the obtained results for different velocity rates. We calculate the corresponding Taylor number in order to show its effect on flow patterns and pressure field.

Handheld Laser Scanner Research

2019 ◽  
Vol 952 (10) ◽  
pp. 47-54
Author(s):  
A.V. Komissarov ◽  
A.V. Remizov ◽  
M.M. Shlyakhova ◽  
K.K. Yambaev
Keyword(s):  
Point Cloud ◽  
Three Dimensional ◽  
Laser Scanner ◽  
Test Site ◽  
Optical Systems ◽  
Advantages And Disadvantages ◽  
Site Survey ◽  
Laser Scanners ◽  
Three Dimensional Models ◽  
The Stability

The authors consider hand-held laser scanners, as a new photogrammetric tool for obtaining three-dimensional models of objects. The principle of their work and the newest optical systems based on various sensors measuring the depth of space are described in detail. The method of simultaneous navigation and mapping (SLAM) used for combining single scans into point cloud is outlined. The formulated tasks and methods for performing studies of the DotProduct (USA) hand-held laser scanner DPI?8X based on a test site survey are presented. The accuracy requirements for determining the coordinates of polygon points are given. The essence of the performed experimental research of the DPI?8X scanner is described, including scanning of a test object at various scanner distances, shooting a test polygon from various scanner positions and building point cloud, repeatedly shooting the same area of the polygon to check the stability of the scanner. The data on the assessment of accuracy and analysis of research results are given. Fields of applying hand-held laser scanners, their advantages and disadvantages are identified.

scholarly journals Gum Tragacanth (GT): A Versatile Biocompatible Material beyond Borders

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1510 ◽  
Author(s):  
Mohammad Ehsan Taghavizadeh Yazdi ◽  
Simin Nazarnezhad ◽  
Seyed Hadi Mousavi ◽  
Mohammad Sadegh Amiri ◽  
Majid Darroudi ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Food Packaging ◽  
Three Dimensional ◽  
Great Promise ◽  
Anionic Polymer ◽  
Gum Tragacanth ◽  
New Horizons ◽  
Tissue Healing ◽  
The Stability ◽  
Therapeutic Substance

The use of naturally occurring materials in biomedicine has been increasingly attracting the researchers’ interest and, in this regard, gum tragacanth (GT) is recently showing great promise as a therapeutic substance in tissue engineering and regenerative medicine. As a polysaccharide, GT can be easily extracted from the stems and branches of various species of Astragalus. This anionic polymer is known to be a biodegradable, non-allergenic, non-toxic, and non-carcinogenic material. The stability against microbial, heat and acid degradation has made GT an attractive material not only in industrial settings (e.g., food packaging) but also in biomedical approaches (e.g., drug delivery). Over time, GT has been shown to be a useful reagent in the formation and stabilization of metal nanoparticles in the context of green chemistry. With the advent of tissue engineering, GT has also been utilized for the fabrication of three-dimensional (3D) scaffolds applied for both hard and soft tissue healing strategies. However, more research is needed for defining GT applicability in the future of biomedical engineering. On this object, the present review aims to provide a state-of-the-art overview of GT in biomedicine and tries to open new horizons in the field based on its inherent characteristics.

Sign in / Sign up

Export Citation Format

Share Document