scholarly journals II.—Circular Magnetisations accompanying Axial and Sectional Currents along Iron Tubes

1895 ◽  
Vol 37 (1) ◽  
pp. 7-16
Author(s):  
Cargill G. Knott
Keyword(s):  
Magnetic Induction ◽  
Entire Length ◽  
The Other ◽  
External Diameter ◽  
Diameter Measurement ◽  
Current Passing ◽  
The Mean ◽  
Iron Tube ◽  
Different Diameters ◽  
A Current

The experiments now to be described have for their object the investigation of the magnetic induction in an iron conductor under the influence of a current passing through it. The method of experiment was briefly in this wise. An iron tube was magnetised circularly by a current passed from end to end along its entire length; and the induction so produced in the iron was measured in terms of the current induced in a coil of wire wound longitudinally round the walls of the tube.In the experiments four tubes were used, all of the same length and nearly the same external diameter. The internal diameters of one pair were approximately double those of the other. The various dimensions are given accurately in the following table, the tubes being distinguished as A, B, a, b. Each diameter measurement is the mean of eight measurements taken across different diameters.

scholarly journals Association of changes of retinal vessels diameter with ocular blood flow in eyes with diabetic retinopathy

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yoshitaka Ueno ◽  
Takeshi Iwase ◽  
Kensuke Goto ◽  
Ryo Tomita ◽  
Eimei Ra ◽  
...  
Keyword(s):  
Blood Flow ◽  
Diabetic Retinopathy ◽  
Adaptive Optics ◽  
Laser Speckle ◽  
The Other ◽  
Systemic Hypertension ◽  
Laser Speckle Flowgraphy ◽  
Retinal Vessels ◽  
External Diameter ◽  
The Mean

AbstractWe investigated morphological changes of retinal arteries to determine their association with the blood flow and systemic variables in type 2 diabetes patients. The patients included 47 non-diabetic retinopathy eyes, 36 mild or moderate nonproliferative diabetic retinopathy (M-NPDR) eyes, 22 severe NPDR (S-NPDR) eyes, 32 PDR eyes, and 24 normal eyes as controls. The mean wall to lumen ratio (WLR) measured by adaptive optics camera was significantly higher in the PDR groups than in all of the other groups (all P < 0.001). However, the external diameter of the retinal vessels was not significantly different among the groups. The mean blur rate (MBR)-vessel determined by laser speckle flowgraphy was significantly lower in the PDR group than in the other groups (P < 0.001). The WLR was correlated with MBR-vessel (r = − 0.337, P < 0.001), duration of disease (r = 0.191, P = 0.042), stage of DM (r = 0.643, P < 0.001), systolic blood pressure (r = 0.166, P < 0.037), and presence of systemic hypertension (r = 0.443, P < 0.001). Multiple regression analysis demonstrated that MBR-vessel (β = − 0.389, P < 0.001), presence of systemic hypertension (β = 0.334, P = 0.001), and LDL (β = 0.199, P = 0.045) were independent factors significantly associated with the WLR. The increased retinal vessel wall thickness led to a narrowing of lumen diameter and a decrease in the blood flow in the PDR group.

Rem Study of Current Effect on the Structure of Clean Si(111) Surface

1990 ◽  
Vol 48 (1) ◽  
pp. 306-307
Author(s):  
A. Yamanaka ◽  
H. Ohse ◽  
K. Yagi
Keyword(s):  
The Other ◽  
Current Direction ◽  
Clean Surface ◽  
Current Effect ◽  
Atomic Steps ◽  
Step Bunching ◽  
Terrace Width ◽  
Step Down ◽  
A Current

Recently current effects on clean and metal adsorbate surfaces have attracted much attention not only because of interesting phenomena but also because of practically importance in treatingclean and metal adsorbate surfaces [1-6]. In the former case, metals deposited migrate on the deposit depending on the current direction and a patch of the deposit expands on the clean surface [1]. The migration is closely related to the adsorbate structures and substrate structures including their anisotropy [2,7]. In the latter case, configurations of surface atomic steps depends on the current direction. In the case of Si(001) surface equally spaced array of monatom high steps along the [110] direction produces the 2x1 and 1x2 terraces. However, a relative terrace width of the two domain depends on the current direction; a step-up current widen terraces on which dimers are parallel to the current, while a step-down current widen the other terraces [3]. On (111) surface, a step-down current produces step bunching at temperatures between 1250-1350°C, while a step-up current produces step bunching at temperatures between 1050-1250°C [5].In the present paper, our REM observations on a current induced step bunching, started independently, are described.Our results are summarized as follows.(1) Above around 1000°C a step-up current induces step bunching. The phenomenon reverses around 1200 C; a step-down current induces step bunching. The observations agree with the previous reports [5].

Multi-Center Study of Thromboplastin Calibration Precision – Influence of Reagent Species, Composition, and International Sensitivity Index (ISI)

1993 ◽  
Vol 69 (01) ◽  
pp. 035-040 ◽  
Author(s):  
A M H P van den Besselaar ◽  
R M Bertina
Keyword(s):  
Oral Anticoagulants ◽  
International Normalized Ratio ◽  
The Other ◽  
World Health ◽  
Rabbit Brain ◽  
Sensitivity Index ◽  
Bovine Plasma ◽  
Significant Difference ◽  
The Mean ◽  
International Sensitivity Index

SummaryFour thromboplastin reagents were tested by 18 laboratories in Europe, North-America, and Australasia, according to a detailed protocol. One thromboplastin was the International Reference Preparation for ox brain thromboplastin combined with adsorbed bovine plasma (coded OBT/79), and the second was a certified reference material for rabbit brain thromboplastin, plain (coded CRM 149R). The other two thromboplastin reagents were another rabbit plain brain thromboplastin (RP) with a lower ISI than CRM 149R and a rabbit brain thromboplastin combined with adsorbed bovine plasma (RC). Calibration of the latter two reagents was performed according to methods recommended by the World Health Organization (W. H. O.).The purpose of this study was to answer the following questions: 1) Is the calibration of the RC reagent more precise against the bovine/combined (OBT/79) than against the rabbit/plain reagent (CRM 149R)? 2) Is the precision of calibration influenced by the magnitude of the International Sensitivity Index (ISI)?The lowest inter-laboratory variation of ISI was observed in the calibration of the rabbit/plain reagent (RP) against the other rabbit/plain reagent (CRM 149R) (CV 1.6%). The highest interlaboratory variation was obtained in the calibration of rabbit/plain (RP) against bovine/combined (OBT/79) (CV 5.1%). In the calibration of the rabbit/combined (RC) reagent, there was no difference in precision between OBT/79 (CV 4.3%) and CRM 149R (CV 4.2%). Furthermore, there was no significant difference in the precision of the ISI of RC obtained with CRM 149R (ISI = 1.343) and the rabbit/plain (RP) reagent with ISI = 1.14. In conclusion, the calibration of RC could be performed with similar precision with either OBT/79 or CRM 149R, or RP.The mean ISI values calculated with OBT/79 and CRM 149R were practically identical, indicating that there is no bias in the ISI of these reference preparations and that these reference preparations have been stable since their original calibration studies in 1979 and 1987, respectively.International Normalized Ratio (INR) equivalents were calculated for a lyophilized control plasma derived from patients treated with oral anticoagulants. There were small but significant differences in the mean INR equivalents between the bovine and rabbit thromboplastins. There were no differences in the interlaboratory variation of the INR equivalents, when the four thromboplastins were compared.

Prothrombin Time Standardization: Report of the Expert Panel on Oral Anticoagulant Control

1979 ◽  
Vol 42 (04) ◽  
pp. 1073-1114 ◽  
Keyword(s):  
Prothrombin Time ◽  
Expert Panel ◽  
The Other ◽  
Rabbit Brain ◽  
Calibration Constant ◽  
Freeze Dried ◽  
The Mean ◽  
Point Of Intersection ◽  
And Control ◽  
Standardization Report

SummaryIn collaborative experiments in 199 laboratories, nine commercial thromboplastins, four thromboplastins held by the National Institute for Biological Standards and Control (NIBS & C), London and the British Comparative Thromboplastin were tested on fresh normal and coumarin plasmas, and on three series of freeze-dried plasmas. One of these was made from coumarin plasmas and the other two were prepared from normal plasmas; in each series, one plasma was normal and the other two represented different degrees of coumarin defect.Each thromboplastin was calibrated against NIBS&C rabbit brain 70/178, from the slope of the line joining the origin to the point of intersection of the mean ratios of coumarin/normal prothrombin times when the ratios obtained with the two thromboplastins on the same fresh plasmas were plotted against each other. From previous evidence, the slopes were calculated which would have been obtained against the NIBS&C “research standard” thromboplastin 67/40, and termed the “calibration constant” of each thromboplastin. Values obtained from the freeze-dried coumarin plasmas gave generally similar results to those from fresh plasmas for all thromboplastins, whereas values from the artificial plasmas agreed with those from fresh plasmas only when similar thromboplastins were being compared.Taking into account the slopes of the calibration lines and the variation between laboratories, precision in obtaining a patient’s prothrombin time was similar for all thromboplastins.

Platelet Suruival and Function in Rats with Enhanced Thrombotic Tendency

1985 ◽  
Vol 54 (04) ◽  
pp. 739-743 ◽  
Author(s):  
Federica Delaini ◽  
Elisabetta Dejana ◽  
Ine Reyers ◽  
Elisa Vicenzi ◽  
Germana De Bellis Vitti ◽  
...  
Keyword(s):  
Arachidonic Acid ◽  
Nephrotic Syndrome ◽  
Platelet Function ◽  
Laboratory Tests ◽  
Thrombus Formation ◽  
The Other ◽  
Mean Survival Time ◽  
The Mean ◽  
And Function ◽  
Thrombotic Tendency

SummaryWe have investigated the relevance of some laboratory tests of platelet function in predicting conditions of thrombotic tendency. For this purpose, we studied platelet survival, platelet aggregation in response to different stimuli, TxB2 and 6-keto-PGFlα production in serum of rats bearing a nephrotic syndrome induced by adriamycin. These animals show a heavy predisposition to the development of both arterial and venous thrombosis. The mean survival time was normal in nephrotic rats in comparison to controls. As to aggregation tests, a lower aggregating response was found in ADR-treated rats using ADP or collagen as stimulating agents. With arachidonic acid (AA) we observed similar aggregating responses at lower A A concentrations, whereas at higher AA concentrations a significantly lower response was found in nephrotic rats, despite their higher TxB2 production. Also TxB2 and 6-keto-PGFlα levels in serum of nephrotic rats were significantly higher than in controls. No consistent differences were found in PGI2-activity generated by vessels of control or nephrotic rats.These data show that platelet function may appear normal or even impaired in rats with a markedly increased thrombotic tendency. On the other hand, the significance of high TxB2 levels in connection with mechanisms leading to thrombus formation remains a controversial issue.

Voronoi Analysis of a Soccer Game

2004 ◽  
Vol 9 (3) ◽  
pp. 233-240 ◽  
Author(s):  
S. Kim
Keyword(s):  
Collective Behavior ◽  
Quantitative Assessment ◽  
The Other ◽  
Analysis Method ◽  
Random System ◽  
Soccer Game ◽  
Voronoi Polygons ◽  
The Mean

This paper describes a Voronoi analysis method to analyze a soccer game. It is important for us to know the quantitative assessment of contribution done by a player or a team in the game as an individual or collective behavior. The mean numbers of vertices are reported to be 5–6, which is a little less than those of a perfect random system. Voronoi polygons areas can be used in evaluating the dominance of a team over the other. By introducing an excess Voronoi area, we can draw some fruitful results to appraise a player or a team rather quantitatively.

The Axis Feature: Illusionary Effects on Children's Judgments of Length

1982 ◽  
Vol 55 (3) ◽  
pp. 720-722
Author(s):  
Anat Scher
Keyword(s):  
Relative Length ◽  
The Other ◽  
Context Model ◽  
Structural Pattern ◽  
Perceptual Judgments ◽  
Length Estimation ◽  
Different Diameters

The effect of the position of lines on length estimation was investigated. 40 5-yr.-olds were asked to compare the two arms of an L-shaped figure presented inside circular frames of different diameters. For each figure one of the arms was on the axis, that is, the diameter, and the other arm was perpendicular to that axis. In making perceptual judgments about the relative length of two lines the children tended to describe the on-axis line as longer than the off-axis line. This illusion which, presumably, reflects a perceptual force induced by the characteristics of the structural pattern, supports the context model of visual anomalies.

Solid, slightly soluble phosphorus compounds as nutrient source in activated sludge treatment of forest industry wastewaters

1997 ◽  
Vol 35 (2-3) ◽  
pp. 131-138 ◽  
Author(s):  
Pirjo-Riitta Rantala ◽  
Hannu Wirola
Keyword(s):  
Activated Sludge ◽  
The Other ◽  
Phosphorus Compounds ◽  
Forest Industry ◽  
Phosphorus Concentration ◽  
Nutrient Source ◽  
Sludge Treatment ◽  
Grain Sizes ◽  
Soluble Phosphorus ◽  
The Mean

The aim of the study was to determine if solid, slightly soluble compounds can be used as nutrient source in activated sludge treatment plants instead of liquid phosphoric acid. Four different solid materials were tested in lab-scale solubility tests to find compounds which are least soluble. Two materials were chosen for further studies: apatite and raw phosphate. The use of apatite and raw phosphate as nutrient source was studied in lab-scale activated sludge reactors along with a control reactor where phosphorus was added in liquid form. The phosphorus dosage, measured as elementary phosphorus, was the same for all three reactors. The reactors were fed with pre-clarified chemi-thermomechanical pulp mill (CTMP) wastewater. There were no significant differences in the reductions of organic matter between the three reactors. The mean effluent concentration of total phosphorus was 3 mg P/l in the control reactor and less than 1 mg P/1 in the other two reactors. The soluble phosphorus concentration was more than 2 mg P/l in the control reactor and less than 0.5 mg P/l in the other two. Apatite was an even better nutrient source than raw phosphate. Further lab-scale tests were conducted using two different grain sizes of apatite. No significant differences were found between the studied grain sizes (&lt;0.074 mm and 0.074 mm-0.125 mm). Apatite was then used in full-scale at a CTMP-mill two different times. The experiments showed that the mean concentrations of phosphorus can be reduced radically by using apatite as a nutrient source instead of liquid phosphorus. Solid phosphorus compounds are a viable alternative to reduce the phosphorus load from forest industry wastewater treatment plants.

scholarly journals The Effect of Route Choice in Children’s Exposure to Ultrafine Particles Whilst Walking to School

2021 ◽  
Vol 18 (15) ◽  
pp. 7808
Author(s):  
Mehrdad Rafiepourgatabi ◽  
Alistair Woodward ◽  
Jennifer A. Salmond ◽  
Kim Natasha Dirks
Keyword(s):  
Ultrafine Particles ◽  
Route Choice ◽  
The Other ◽  
Close Proximity ◽  
Public Health Officials ◽  
Risk Of Exposure ◽  
The Mean ◽  
Walking To School ◽  
Elevated Exposure ◽  
Children’S Exposure

Children walking to school are at a high risk of exposure to air pollution compared with other modes because of the time they spend in close proximity to traffic during their commute. The aim of this study is to investigate the effect of a walker’s route choice on their exposure to ultrafine particles (UFP) on the walk to school. During morning commutes over a period of three weeks, exposure to UFP was measured along three routes: two routes were alongside both sides of a busy arterial road with significantly higher levels of traffic on one side compared to the other, and the third route passed through quiet streets (the background route). The results indicate that the mean exposure for the pedestrian walking along the background route was half the exposure experienced on the other two routes. Walkers on the trafficked side were exposed to elevated concentrations (>100,000 pt/cc) 2.5 times longer than the low-trafficked side. However, the duration of the elevated exposure for the background route was close to zero. Public health officials and urban planners may use the results of this study to promote healthier walking routes to schools, especially those planned as part of organized commutes.

Yields of mixtures of single-cross hybrid field beans (Viciafaba L.) with one of the parental inbred lines

1966 ◽  
Vol 67 (2) ◽  
pp. 235-237 ◽  
Author(s):  
D. A. Bond ◽  
J. L. Fyfe ◽  
Gillian Toynbee-Clarke
Keyword(s):  
Inbred Lines ◽  
The Other ◽  
Normal Rate ◽  
Single Cross ◽  
Parental Inbred ◽  
The Mean ◽  
Field Beans

The yields of seed from a hybrid, one of its parents and different mixtures of the hybrid and parent were compared in the case of two different hybrids. Open-pollinated controls were included in the trial, which was sown at about the normal rate for beans. With both hybrids a mixture of 11 of hybrid to 1 of parent yielded as well as the hybrid itself and mixtures of 2 of hybrid to 1 of parent yielded in both cases about 7 cwt./acro more than the mean of the open-pollinated controls. With the higher-yielding hybrid, which had less contrast in vegetative vigour between hybrid and parent, mixtures in the proportions 5:1 and 2:1 showed declining yields, but with the other hybrid they yielded as well as the pure hybrid.

Sign in / Sign up

Export Citation Format

Share Document