Comparison of TEM and STM observations of small silver clusters on different carbon supports

1990 ◽  
Vol 48 (4) ◽  
pp. 264-265
Author(s):  
Bernd Tesche ◽  
Tobias Schilling
Keyword(s):  
Vibration Isolation ◽  
Pyrolytic Graphite ◽  
Carbon Film ◽  
Silver Clusters ◽  
Carbon Supports ◽  
Stacking Order ◽  
System P ◽  
High Resolution Tem ◽  
High Degree ◽  
Degree Of Order

The objective of our work is to determine:a) whether both of the imaging methods (TEM, STM) yield comparable data andb) which method is better suited for a reliable structure analysis of microclusters smaller than 1.5 nm, where a deviation of the bulk structure is expected.The silver was evaporated in a bell-jar system (p 10−5 pa) and deposited onto a 6 nm thick amorphous carbon film and a freshly cleaved highly oriented pyrolytic graphite (HOPG).The average deposited Ag thickness is 0.1 nm, controlled by a quartz crystal microbalance at a deposition rate of 0.02 nm/sec. The high resolution TEM investigations (100 kV) were executed by a hollow-cone illumination (HCI). For the STM investigations a commercial STM was used. With special vibration isolation we achieved a resolution of 0.06 nm (inserted diffraction image in Fig. 1c). The carbon film shows the remarkable reduction in noise by using HCI (Fig. 1a). The HOPG substrate (Fig. 1b), cleaved in sheets thinner than 30 nm for the TEM investigations, shows the typical arrangement of a nearly perfect stacking order and varying degrees of rotational disorder (i.e. artificial single crystals). The STM image (Fig. 1c) demonstrates the high degree of order in HOPG with atomic resolution.

Feasibility of Molecular Structure Determination With a High Resolution Electron Microscope

1968 ◽  
Vol 26 ◽  
pp. 338-339
Author(s):  
T. A. Welton
Keyword(s):  
Electron Microscope ◽  
Substrate Surface ◽  
Helical Axis ◽  
Base Plane ◽  
Resolution Electron ◽  
High Resolution Electron Microscope ◽  
High Degree ◽  
Degree Of Order ◽  
Purine Pyrimidine

An ultimate design goal for an improved electron microscope, aimed at biological applications, is the determination of the structure of complex bio-molecules. As a prototype of this class of problems, we propose to examine the possibility of reading DNA sequence by an imaginable instrument design. This problem ideally combines absolute importance and relative simplicity, in as much as the problem of enzyme structure seems to be a much more difficult one.The proposed technique involves the deposition on a thin graphite lamina of intact double helical DNA rods. If the structure can be maintained under vacuum conditions, we can then make use of the high degree of order to greatly reduce the work involved in discriminating between the four possible purine-pyrimidine arrangements in each base plane. The phosphorus atoms of the back bone form in projection (the helical axis being necessarily parallel to the substrate surface) two intertwined sinusoids. If these phosphorus atoms have been located up to a certain point on the molecule, we have available excellent information on the orientation of the base plane at that point, and can then locate in projection the key atoms for discrimination of the four alternatives.

The Organization of Actin Filaments in the Stereocilia of the Bird Cochlea

1980 ◽  
Vol 38 ◽  
pp. 554-555
Author(s):  
E.J. Battles ◽  
D. DeRosier ◽  
J.C. Saunders ◽  
L.G. Tilney
Keyword(s):  
Hair Cell ◽  
Diffraction Pattern ◽  
Sea Urchin ◽  
Actin Filaments ◽  
Optical Diffraction ◽  
Dense Material ◽  
Apical Surface ◽  
Structural Rigidity ◽  
High Degree ◽  
Degree Of Order

Extending from the apical surface of each hair cell of the chick cochlea are from 75 to 200 microvilli or stereocllia and one true cllium, the kinocilium. The stereocllia are arranged in rows of progressively increasing length (Fig. 1). Within each tapering sterocilium is a bundle of actin filaments with over 900 filaments near the tip yet only approximately 25 at the base where filaments are enmeshed in a dense material (Fig. 1); from here some of the filaments enter the apical surface of the cell (cuticular plate) as a rootlet. Examination of longitudinal sections of the stereocilia (Fig. 2) show that the filaments are aligned parallel to each other and show considerable order. Examination of an optical diffraction pattern of this bundle (Fig. 4) reveal that the actin filaments are packed such that the crossover points of adjacent actin filaments are inregister. A prominent reflection at 125Å−1 demonstrates that the filaments are cjossbridged by a macromolecular bridge situated at an average of 125Å−1 intervals (Fig. 4) in transverse sections the filaments appear hexagonally packed although there are regions where the filaments are less ordered (Fig. 3). In images processed in the computer to remove, noise and enhance detail periodic nature of the bridge can be clearly seen (see arrows Fig. 5). This image resembles that of an actin paracrystal formed from sea urchin extract composed of bundles of actin filaments crossbridged by a second protein. Thus the actin filaments in the bird stereocilia by being cross-bridged and packed with a high degree of order and produces a structure with considerable structural rigidity. Embryos were studied at various stages in development in an attempt to determine how the stereocilia form and how does the actin packing develops. These stages will be discussed.

Three-Dimensional Hexagonal Close-Packed Superlattices of Passivated Ag Nanocrystals

1997 ◽  
Vol 3 (S2) ◽  
pp. 431-432
Author(s):  
S. A. Harfenist ◽  
Z. L. Wang ◽  
R. L. Whetten ◽  
I. Vezmar ◽  
M. M. Alvarez ◽  
...  
Keyword(s):  
Carbon Film ◽  
Three Dimensional ◽  
Structure Characterization ◽  
Self Assembled Monolayers ◽  
Hexagonal Close Packed ◽  
Self Assembling ◽  
Transmission Electron ◽  
Assembled Monolayers ◽  
High Resolution Tem ◽  
Nanocrystal Superlattices

Silver nanocrystals passivated by dodecanethiol self-assembled monolayers were produced using an aerosol technique described in detail elsewhere [1]. Self-assembling passivated nanocrystal-superlattices (NCS's) involve self-organization into monolayers, thin films, and superlattices of size-selected nanoclusters encapsulated in a protective compact coating [2,3,4,5,6,7]. We report the preparation and structure characterization of three-dimensional (3-D) hexagonal close-packed Ag nanocrystal supercrystals from Ag nanocrystals of ˜4.5 nm in diameters. The crystallography of the superlattice and atomic core lattices were determined using transmission electron microscopy (TEM) and high-resolution TEM.SEM was used to image the nanocrystal superlattices formed on an amorphous carbon film of an TEM specimen grid (fig. la). The superlattice films show well shaped, sharply faceted, triangular shaped sheets. Figure lb depicts numerous Ag nanocrystal aggregates uniformly distributed over the imaging region. Inset in this figure is an enlargement of the boxed region at the edge of a supercrystal typifying the ordered nanocrystal packing.

scholarly journals Field Emission from Carbon Films Deposited by Controlled-Low-Energy Beams and CVD Sources

1999 ◽  
Vol 585 ◽  
Author(s):  
Douglas H. Lowndes ◽  
Vladimir I. Merkulov ◽  
L. R. Baylor ◽  
G. E. Jellison ◽  
D. B. Poker ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Surface Morphology ◽  
Field Emission ◽  
Metal Ion ◽  
Ion Beam ◽  
Pyrolytic Graphite ◽  
Carbon Film ◽  
Chemical Vapor ◽  
Carbon Films ◽  
Damage Site

AbstractThe principal interests in this work are energetic-beam control of carbon-film properties and the roles of doping and surface morphology in field emission. Carbon films with variable sp3-bonding fraction were deposited on n-type Si substrates by ArF (193 nm) pulsed-laser ablation (PLA) of a pyrolytic graphite target, and by direct metal ion beam deposition (DMIBD) using a primary Cs+ beam to generate the secondary C- deposition beam. The PLA films are undoped while the DMIBD films are doped with Cs. The kinetic energy (KE) of the incident C atoms/ions was controlled and varied over the range from ∼25 eV to ∼175 eV. Earlier studies have shown that C films' sp3-bonding fraction and diamond-like properties can be maximized by using KE values near 90 eV. The films' surface morphology, sp3–bonding fraction, and Cs-content were determined as a function of KE using atomic force microscopy, TEM/EELS, Rutherford backscattering and nuclear reaction measurements, respectively. Field emission (FE) from these very smooth undoped and Cs-containing films is compared with the FE from two types of deliberately nanostructured carbon films, namely hot-filament chemical vapor deposition (HF-CVD) carbon and carbon nanotubes grown by plasma-enhanced CVD. Electron field emission (FE) characteristics were measured using ∼25-μm, ∼5-μm and ∼1-μm diameter probes that were scanned with ∼75 nm resolution in the x-, y-, and z-directions in a vacuum chamber (∼5 × 10-7 torr base pressure) equipped with a video camera for viewing. The hydrogen-free and very smooth a-D or a-C films (with high or low sp3 content, and with or without ∼1% Cs doping) produced by PLD and DMIBD are not good field emitters. Conditioning accompanied by arcing was required to obtain emission, so that their subsequent FE is characteristic of the arc-produced damage site. However, deliberate surface texturing can eliminate the need for conditioning, apparently by geometrical enhancement of the local electric field. But the most promising approach for producing macroscopically flat FE cathodes is to use materials that are highly nanostructured, either by the deposition process (e.g. HF-CVD carbon) or intrinsically (e.g. carbon nanotubes). HF-CVD films were found to combine a number of desirable properties for FE displays and vacuum microelectronics, including the absence of conditioning, low turn-on fields, high emission site density, and apparent stability and durability during limited long-term testing. Preliminary FE measurements revealed that vertically aligned carbon nanotubes are equally promising.

Enthalpien von Kupfer- und Silberchalkogeniden / Enthalpies of Copper and Silver Chalcogenides

1978 ◽  
Vol 33 (2) ◽  
pp. 190-196 ◽  
Author(s):  
Roger Blachnik ◽  
Paul-G. Gunia
Keyword(s):  
Thermodynamic Data ◽  
Transition Temperatures ◽  
Melting Points ◽  
Drop Calorimeter ◽  
Silver Chalcogenides ◽  
Increasing Temperature ◽  
High Degree ◽  
Degree Of Order ◽  
Bond Character

The enthalpy contents of Cu2Se, Cu2Te, Ag2Se and Ag2Te at temperatures between 350 K to 50 K above the melting points were measured in an isoperibolic drop-calorimeter. Thermodynamic data of the compounds were derived from these measurements. An analysis of the data leads to the conclusion that a high degree of order is retained in the melts of these compounds, and that the bond character of these melts is partially ionic. An unusual decrease of Cp with increasing temperature immidiately after the transition temperatures could be confirmed.

scholarly journals Coherent curvature radiation and fast radio bursts

2018 ◽  
Vol 613 ◽  
pp. A61 ◽  
Author(s):  
Gabriele Ghisellini ◽  
Nicola Locatelli
Keyword(s):  
Observational Constraints ◽  
Acceleration Process ◽  
Radio Bursts ◽  
Radiation Mechanism ◽  
Curvature Radiation ◽  
Inverse Compton ◽  
Transient Events ◽  
Radio Band ◽  
High Degree ◽  
Degree Of Order

Fast radio bursts are extragalactic radio transient events lasting a few milliseconds with a ~Jy flux at ~1 GHz. We propose that these properties suggest a neutron star progenitor, and focus on coherent curvature radiation as the radiation mechanism. We study for which sets of parameters the emission can fulfil the observational constraints. Even if the emission is coherent, we find that self-absorption can limit the produced luminosities at low radio frequencies and that an efficient re-acceleration process is needed to balance the dramatic energy losses of the emitting particles. Self-absorption limits the luminosities at low radio frequency, while coherence favours steep optically thin spectra. Furthermore, the magnetic geometry must have a high degree of order to obtain coherent curvature emission. Particles emit photons along their velocity vectors, thereby greatly reducing the inverse Compton mechanism. In this case we predict that fast radio bursts emit most of their luminosities in the radio band and have no strong counterpart in any other frequency bands.

scholarly journals Two-dimensional crystals formed from photosynthetic reaction centers.

1983 ◽  
Vol 97 (4) ◽  
pp. 1266-1270 ◽  
Author(s):  
K R Miller ◽  
J S Jacob
Keyword(s):  
Electron Microscopy ◽  
Single Unit ◽  
Reaction Centers ◽  
Unit Cell ◽  
Two Dimensional ◽  
Photosynthetic Reaction Centers ◽  
Photosynthetic Membranes ◽  
Fourier Techniques ◽  
High Degree ◽  
Degree Of Order

Photosynthetic reaction centers from the bacterium Rhodopseudomonas viridis were prepared after detergent solubilization of photosynthetic membranes. The purified reaction centers, in agreement with reports from other laboratories, contain four distinct polypeptides ranging in molecular weight from 28,000 to 41,000. When the detergent was gradually removed by dialysis under appropriate conditions, large two-dimensional sheets of reaction centers were formed, suitable for analysis by electron microscopy. The crystals were rectangular, and the dimensions of a single unit cell were 121 X 129 A. Each unit cell contained four distinct subunits, each with approximate dimensions of 45 X 60 A. The thickness of the sheet was 60 A. Preliminary studies of the sheets with negative staining indicated that the sheets show a high degree of order: as many as six orders are visible in transforms of the images. Because of the fact that in R. viridis the native membrane from which these reaction centers were purified also displays a crystal-like structure, comparative studies between a membrane and one of its components, each analyzed by Fourier techniques, are now possible.

Order, information and time

2018 ◽  
Author(s):  
Dennis Sherwood ◽  
Paul Dalby
Keyword(s):  
Second Law ◽  
Economic Systems ◽  
High Performing ◽  
Flow Of Time ◽  
The Difference ◽  
Thermodynamic Probability ◽  
High Degree ◽  
Low Entropy ◽  
Degree Of Order ◽  
Over Time

This chapter broadens the reader’s appreciation, and understanding, of entropy. Starting with the reader’s intrinsic recognition of the difference between an ‘ordered’ and a ‘disordered’ state, this chapter introduces the concepts of microstates, macrostates and thermodynamic probability, leading firstly to the Boltzmann equation, and then to the relationships between entropy and the flow of time, entropy and information, and Maxwell’s demon. Finally, this chapter introduces the less familiar topics of ‘thermoeconomics’ - the application of the principles of thermodynamics to economic systems – and ‘organodynamics’ – the idea that high-performing teams are systems which maintain a high degree of order, and low entropy, over time, without breaking the Second Law.

Sign in / Sign up

Export Citation Format

Share Document