Direct Insights on Flax Fiber Structure by Focused Ion Beam Microscopy

2010 ◽  
Vol 16 (2) ◽  
pp. 175-182 ◽  
Author(s):  
Bernadette Domenges ◽  
Karine Charlet
Keyword(s):  
Electron Microscopy ◽  
Cell Wall ◽  
Cross Sections ◽  
Secondary Cell Wall ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Flax Fibers ◽  
Transmission Electron ◽  
Transition Modes ◽  
Beam Currents

AbstractIn this article, it is shown that focused ion beam (FIB) systems can be used to study the inner structure of flax fibers, the use of which as a reinforcing material in polymer composites still draws much interest from multiple disciplines. This technique requires none of the specific preparations necessary for scanning electron microscopy or transmission electron microscopy studies. Irradiation experiments performed on FIB prepared cross sections with very low Ga+ion beam currents revealed the softer material components of fibers. Thus, it confirmed the presence of pectin-rich layers at the interfaces between the fibers of a bundle, but also allowed the precise localization of such layers within the secondary cell wall. Furthermore, it suggested new insights on the transition modes between the sublayers of the secondary cell wall.

Alleviating Sample Charging during FIB Operation

2015 ◽  
Author(s):  
Q. Liu ◽  
H.B. Kor ◽  
Y.W. Siah ◽  
C.L. Gan
Keyword(s):  
Electron Microscopy ◽  
Cross Sections ◽  
Focused Ion Beam ◽  
Semiconductor Device ◽  
Ion Beam ◽  
Semiconductor Industry ◽  
Milling Process ◽  
Front Side ◽  
Dual Beam ◽  
Transmission Electron

Abstract Dual-beam focused ion beam (DB-FIB) system is widely used in the semiconductor industry to prepare cross-sections and transmission electron microscopy (TEM) lamellae, modify semiconductor devices and verify layout. One of the factors that limits its success rate is sample charging, which is caused by a lack of conductive path to discharge the accumulated charges. In this paper, an approach using an insitu micromanipulator was investigated to alleviate the charging effects. With this approach, a simple front side semiconductor device modification was carried out and the corresponding stage current was monitored to correlate to the milling process.

Deformation under nanoindents in Si, Ge, and GaAs examined through transmission electron microscopy

2001 ◽  
Vol 16 (12) ◽  
pp. 3347-3350 ◽  
Author(s):  
S. J. Lloyd ◽  
J. M. Molina-Aldareguia ◽  
W. J. Clegg
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Cross Sections ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Amorphous Material ◽  
Face Centered Cubic ◽  
Dislocation Generation ◽  
Transmission Electron ◽  
Face Centered

Cross sections through nanoindents on Si, Ge, and GaAs {001} were examined through transmission electron microscopy. A focused ion beam workstation was used to machine electron transparent windows through the indents. In both Si and Ge there was a transformed zone immediately under the indent composed of amorphous material and a mixture of face-centered-cubic and body-centered cubic crystals. Cracking and dislocation generation were also observed around the transformed zone. In GaAs the dominant deformation mechanism was twinning on the {11} planes. The hardness of these materials is discussed in light of these observations and their macroscopic material properties such as phase transformation pressure.

A Stress Relief Method to Control Warping of Focused Ion Beam Prepared Membranes for Transmission Electron Microscopy

2000 ◽  
Vol 6 (S2) ◽  
pp. 532-533
Author(s):  
B.B. Rossie ◽  
F.A. Stevie ◽  
T.L. Shofner ◽  
S.R. Brown ◽  
R.B. Irwin
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Focused Ion Beam ◽  
Bulk Material ◽  
Ion Beam ◽  
Limiting Factor ◽  
Specimen Preparation ◽  
Final Thickness ◽  
Transmission Electron ◽  
Beam Currents

The continued decrease in microelectronic feature dimensions has led to a reliance on the focused ion beam (FIB) for site-specific transmission electron microscopy (TEM) specimen preparation. To maximize the capabilities of the FIB, methods must be developed to consistently produce specimens thin enough to generate TEM lattice images. The limiting factor in producing quality TEM specimens by either the traditional or lift-out method is the final thickness of the specimen.The FIB is used to prepare TEM specimens by removing the bulk material that surrounds a desired feature by sputtering with a focused gallium ion beam. Successively lower beam currents are used to sputter away material until an electron transparent membrane (-0.2 μm) containing the desired feature remains. For a 300 keV TEM, lattice imaging of silicon requires additional membrane thinning to less than 0.05 μm.The loss of rigidity during the thinning process makes the membrane highly prone to deformation due to residual stresses, linear expansion, and ion beam interaction.

Measurement of Crystal Lattice Rotations under Nanoindents in Copper

2004 ◽  
Vol 841 ◽  
Author(s):  
Kirsten K. McLaughlin ◽  
Nadia A. Stelmashenko ◽  
Stephen J. Lloyd ◽  
Luc J. Vandeperre ◽  
William J. Clegg
Keyword(s):  
Electron Microscopy ◽  
Crystal Lattice ◽  
Cross Sections ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Convergent Beam Electron Diffraction ◽  
Copper Crystal ◽  
Beam Electron ◽  
Transmission Electron ◽  
Convergent Beam

ABSTRACTA technique is described to measure the rotations of the crystal lattice in the deformed region around a nanoindent from volumes smaller than 3 × 10−5 μm3. To demonstrate this method, a copper crystal has been indented on its (001) face to depths of 500 and 1300 nm. Cross-sections of nanoindents were prepared for transmission electron microscopy by focused ion beam milling, and rotations were measured about the [001], [010] and [100] axes using convergent beam electron diffraction.

TEM Sample Preparation Tricks for Advanced DRAMs

2015 ◽  
Author(s):  
Ching Shan Sung ◽  
Hsiu Ting Lee ◽  
Jian Shing Luo
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Tem Analysis ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Characterization Of Materials

Abstract Transmission electron microscopy (TEM) plays an important role in the structural analysis and characterization of materials for process evaluation and failure analysis in the integrated circuit (IC) industry as device shrinkage continues. It is well known that a high quality TEM sample is one of the keys which enables to facilitate successful TEM analysis. This paper demonstrates a few examples to show the tricks on positioning, protection deposition, sample dicing, and focused ion beam milling of the TEM sample preparation for advanced DRAMs. The micro-structures of the devices and samples architectures were observed by using cross sectional transmission electron microscopy, scanning electron microscopy, and optical microscopy. Following these tricks can help readers to prepare TEM samples with higher quality and efficiency.

Fin Level Defect Isolation Inside a FinFET Using Electron Beam Alteration of Current Flow

2017 ◽  
Author(s):  
H.J. Ryu ◽  
A.B. Shah ◽  
Y. Wang ◽  
W.-H. Chuang ◽  
T. Tong
Keyword(s):  
Electron Microscopy ◽  
Electron Beam ◽  
Focused Ion Beam ◽  
Current Flow ◽  
Ion Beam ◽  
The Body ◽  
Complete Understanding ◽  
Root Cause ◽  
Transmission Electron ◽  
Defect Isolation

Abstract When failure analysis is performed on a circuit composed of FinFETs, the degree of defect isolation, in some cases, requires isolation to the fin level inside the problematic FinFET for complete understanding of root cause. This work shows successful application of electron beam alteration of current flow combined with nanoprobing for precise isolation of a defect down to fin level. To understand the mechanism of the leakage, transmission electron microscopy (TEM) slice was made along the leaky drain contact (perpendicular to fin direction) by focused ion beam thinning and lift-out. TEM image shows contact and fin. Stacking fault was found in the body of the silicon fin highlighted by the technique described in this paper.

Transmission Electron Microscopy (TEM) Specimen Preparation Technique using Focused Ion Beam (FIB): Application to Material Characterization of Chemical Vapor Deposition of Tungsten (W) and Tungsten Silicides (WSix)

1997 ◽  
Author(s):  
K. Doong ◽  
J.-M. Fu ◽  
Y.-C. Huang
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Chemical Vapor ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Transmission Electron

Abstract The specimen preparation technique using focused ion beam (FIB) to generate cross-sectional transmission electron microscopy (XTEM) samples of chemical vapor deposition (CVD) of Tungsten-plug (W-plug) and Tungsten Silicides (WSix) was studied. Using the combination method including two axes tilting[l], gas enhanced focused ion beam milling[2] and sacrificial metal coating on both sides of electron transmission membrane[3], it was possible to prepare a sample with minimal thickness (less than 1000 A) to get high spatial resolution in TEM observation. Based on this novel thinning technique, some applications such as XTEM observation of W-plug with different aspect ratio (I - 6), and the grain structure of CVD W-plug and CVD WSix were done. Also the problems and artifacts of XTEM sample preparation of high Z-factor material such as CVD W-plug and CVD WSix were given and the ways to avoid or minimize them were suggested.

Sign in / Sign up

Export Citation Format

Share Document