A printed wide-beamwidth circularly polarized antenna via two pairs of radiating slots placed in a square contour

2016 ◽  
Vol 9 (3) ◽  
pp. 649-656 ◽  
Author(s):  
Neng-Wu Liu ◽  
Lei Zhu ◽  
Wai-Wa Choi
Keyword(s):  
Ground Plane ◽  
Large Angle ◽  
Axial Ratio ◽  
Dielectric Substrate ◽  
Slot Antenna ◽  
Radiation Patterns ◽  
Circularly Polarized ◽  
Low Profile ◽  
Orthogonal Pairs ◽  
Good Agreement

A low-profile circularly polarized (CP) slot antenna to achieve a wide axial-ratio (AR) beamwidth is proposed in this paper. The radiating patch consists of two orthogonal pairs of parallel slots etched symmetrically onto a ground plane. Firstly, our theoretical study demonstrates that the CP radiation can be satisfactorily achieved at the broadside, when the vertical and horizontal paired-slots are excited in the same amplitude with 90° phase difference. Secondly, the principle of CP radiation of the proposed antenna on an infinite ground plane is described. Through analyzing the spacing between two parallel slots, the |Eθ| and |Eφ| radiation patterns can be made approximately identical with each other over a large angle range. As such, the slot antenna achieves a wide AR beamwidth. After that, the 3 dB AR beamwidth with respect to the size of a finite ground plane is investigated to constitute a practical CP antenna on a finite ground plane. In final, the proposed CP antenna with a 1–4 probe-to-microstrip feeding network is designed and fabricated on a finite ground plane of a dielectric substrate. Measured results are shown to be in good agreement with the simulated ones about the gain, reflection coefficient, AR bandwidth, and radiation patterns. Most importantly, a wide 3 dB AR beamwidth of 126° and low-profile property with the height of 0.036λ0 are achieved.

A low-profile triple-band circularly polarized wide slot antenna for wireless systems

2018 ◽  
Vol 11 (1) ◽  
pp. 67-75 ◽  
Author(s):  
Shilpee Patil ◽  
A. K. Singh ◽  
Binod K. Kanaujia ◽  
R. L. Yadava
Keyword(s):  
Ground Plane ◽  
Wireless Systems ◽  
Axial Ratio ◽  
Slot Antenna ◽  
Slot Antennas ◽  
Circularly Polarized ◽  
Rectangular Patch ◽  
Low Profile ◽  
Good Agreement ◽  
Triple Band

AbstractA simple design for triple-band circularly polarized (CP) wide slot antennas is proposed and experimentally investigated. The proposed antenna having a microstrip-fed rectangular patch with T-shaped notch for triple-band operation and a modified wide square slot on ground plane for CP operation. The measured 10 dB reflection bandwidths are 1.24% (≈340 MHz from 2.56 to 2.9 GHz), 9.63% (≈430 MHz from 4.25 to 4.68 GHz), and 5.34% (≈490 MHz from 8.93 to 9.42 GHz). The generated 3 dB axial ratio bandwidths of the proposed antenna are 7.54, 8.98, and 1.65% at operating frequencies around 2.65, 4.45, and 9.09 GHz, respectively. The measured peak gains within the 3 dB axial ratio bands are 3.03, 3.5, and 5.64 dBi. The simulated and measured results for the return loss, axial ratio, and antenna gain show a good agreement, which validate the antenna design.

Design of Dual Band Dual Sense Circularly Polarized Wide Slot Antenna with C-shaped Radiator for Wireless Applications

Frequenz ◽  
2018 ◽  
Vol 72 (7-8) ◽  
pp. 343-351 ◽  
Author(s):  
Shilpee Patil ◽  
A. K. Singh ◽  
Binod K. Kanaujia ◽  
R. L. Yadava
Keyword(s):  
Ground Plane ◽  
Axial Ratio ◽  
Dual Band ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Circularly Polarized ◽  
Wireless Applications ◽  
Centre Frequency ◽  
Low Profile ◽  
Peak Gain

Abstract A low profile wide slot antenna for dual band and dual sense circular polarization (CP) is proposed here and is simulated by using HFSS simulation software.The proposed antenna having a C shaped patch for dual band operation and a wide square slot etched on the ground with two strips for CP operation. In between radiating patch and ground plane, designed antenna has a layer of easily available dielectric (FR-4) material. Proposed antenna shows an impedance bandwidth of 13.8 % at 2.38 GHz of centre frequency and 9.7 % at 4.43 GHz of centre frequency for lower and upper band respectively. The 3-dB axial ratio (AR) bandwidths for lower and upper band are 18.8 % (at 2.44 GHz of centre frequency) and 13.3 % (at 4.29 GHz of centre frequency), respectively. The peak gain for the lower and upper band is found as 4.1 dBi and 3.3 dBi, respectively. A close agreement has been found between the simulated and the measured results.

scholarly journals CPW-fed circularly-polarized antenna array with high front-to-back ratio and low-profile

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 651-655 ◽  
Author(s):  
Yilin Liu ◽  
Kama Huang
Keyword(s):  
Antenna Array ◽  
Coplanar Waveguide ◽  
Ground Plane ◽  
Axial Ratio ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Feeding Method ◽  
Circularly Polarized ◽  
Low Profile ◽  
Novel Design

Abstract A novel design of a coplanar waveguide (CPW) feed antenna array with circular polarization (CP) and a high front-to-back ratio is described. The proposed CP array is achieved by using a compact CPW–slotline transition network etched in the ground plane. The measured results show that this kind of feeding method can improve the impedance bandwidth, as well as the axial ratio bandwidth of the CP antenna array and provide adequate gain. The proposed array can achieve a 6.08% impedance bandwidth and a 4.10% CP bandwidth. Details of the antenna design and experimental results are presented and discussed.

Development and Miniaturized of Circularly Polarization Diversity at Cavity Backed SIW Antenna for X-Band Application

Frequenz ◽  
2019 ◽  
Vol 73 (9-10) ◽  
pp. 317-320
Author(s):  
Saeid Karamzadeh ◽  
Vahid Rafiei ◽  
Hasan Saygin
Keyword(s):  
Schottky Diodes ◽  
Axial Ratio ◽  
Impedance Bandwidth ◽  
Polarization Diversity ◽  
Circularly Polarized ◽  
Left Hand ◽  
Low Profile ◽  
X Band ◽  
Coaxial Feed ◽  
Good Agreement

Abstract In this work circularly polarization diversity has been achieved by utilizing two Schottky diodes on low profile cavity-backed substrate integrated waveguide (CBSIW). In comparison with other studies in the literature, the size of antenna has been reduced to 0.54λg × 0.76λg by helping a 50-Ohm coaxial feed line. The impedance bandwidth, axial ratio bandwidth and antenna gain are improved to 10.02 %, 5.2 % and 7.68dBi, respectively. In addition, the proposed antenna can generate either a left-hand circularly polarized (LHCP) or a right-hand circularly polarized (RHCP) radiation. The developed antenna was fabricated and tested and the achieved results were in good agreement with the simulated one.

Analysis and design of inclined fractal defected ground-based circularly polarized antenna for CA-band applications

2020 ◽  
pp. 1-10
Author(s):  
Sonal Gupta ◽  
Shilpee Patil ◽  
Chhaya Dalela ◽  
Binod Kumar Kanaujia
Keyword(s):  
Ground Plane ◽  
Axial Ratio ◽  
Mobile Wimax ◽  
Impedance Bandwidth ◽  
Ieee 802.16E ◽  
Defected Ground Structure ◽  
Circularly Polarized ◽  
Analysis And Design ◽  
Centre Frequency ◽  
Good Agreement

Abstract Design of single-feed circularly polarized (CP) microstrip antenna is proposed in this article. The design employs the concept of E-shape patch with inclined fractal defected ground structure (IFDGS), which can improve the impedance bandwidth, gain, and axial ratio (AR) bandwidth. The excellent enhanced impedance bandwidth, axial ratio bandwidth, and gain are achieved by an inclined E-shaped fractal etched on the ground plane. The parameter studies of the E-shaped IFDGS are given to illustrate the way to obtain CP radiation. The third iterative IFDGS is fabricated on easily available FR4 substrate with a size of 0.494 λ0 × 0.494 λ0 × 0.019 λ0 (λ0 is the wavelength in free space at 3.624 GHz). The measured results verify the simulated results and show good agreement. The proposed antenna shows an impedance bandwidth of 12.7% at a centre frequency of 3.47 GHz and 3-dB AR bandwidth for this band is 2.39% at a centre frequency of 3.626 GHz. The measured peak gain for the proposed antenna is found as 8.1 dBi. The proposed antenna can be suitable for mobile WIMAX operation (IEEE 802.16e-2005 standard), wireless communication in CA-band and FCC.

Circularly polarized square slot microstrip antenna for RFID applications

2015 ◽  
Vol 8 (8) ◽  
pp. 1237-1242 ◽  
Author(s):  
Neha Sharma ◽  
Anil Kumar Gautam ◽  
Binod Kumar Kanaujia
Keyword(s):  
Radio Frequency Identification ◽  
Microstrip Antenna ◽  
Axial Ratio ◽  
Slot Antenna ◽  
Circularly Polarized ◽  
Broad Bandwidth ◽  
Antenna Performance ◽  
Frequency Identification ◽  
Rfid Applications ◽  
Good Agreement

In this paper, a novel circularly polarized square slot microstrip antenna is proposed for radio frequency identification (RFID) applications. The circular polarization is achieved by incorporating an arc-shaped strip in the square slot antenna. This antenna is fed by deformed bent feeding line to achieve a broad bandwidth (BW). The key parameters of the antenna are used for parametric study to understand the influence on the antenna performance. To validate simulation results of the design, a prototype is fabricated on the commercially available FR4 material. Measured results show a good agreement with the simulated results. It is found that the antenna shows an impedance BW of 170 MHz (844–1014 MHz) and axial-ratio BW of 170 MHz (834–1004 MHz), which shows that the proposed antenna is a good candidate to be used as a RFID antenna.

scholarly journals A Low-Profile Circularly Polarized Conical-Beam Antenna with Wide Overlap Bandwidth

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Wei He ◽  
Yejun He ◽  
Long Zhang ◽  
Sai-Wai Wong ◽  
Wenting Li ◽  
...  
Keyword(s):  
Electric Field ◽  
Patch Antenna ◽  
Ground Plane ◽  
Axial Ratio ◽  
Impedance Bandwidth ◽  
Beam Radiation ◽  
Circularly Polarized ◽  
Low Profile ◽  
Two Sides ◽  
Conical Beam

In this paper, a low-profile circularly polarized (CP) conical-beam antenna with a wide overlap bandwidth is presented. Such an antenna is constructed on the two sides of a square substrate. The antenna consists of a wideband monopolar patch antenna fed by a probe in the center and two sets of arc-hook-shaped branches. The monopolar patch antenna is loaded by a set of conductive shorting vias to achieve a wideband vertically polarized electric field. Two sets of arc-hook-shaped parasitic branches connected to the patch and ground plane can generate a horizontally polarized electric field. To further increase the bandwidth of the horizontally polarized electric field, two types of arc-hook-shaped branches with different sizes are used, which can generate another resonant frequency. When the parameters of the arc-hook-shaped branches are reasonably adjusted, a 90° phase difference can be generated between the vertically polarized electric field and the horizontally polarized electric field, so that the antenna can produce a wideband CP radiation pattern with a conical beam. The proposed antenna has a wide impedance bandwidth ( ∣ S 11 ∣ < − 10   dB ) of 35.6% (4.97-7.14 GHz) and a 3 dB axial ratio (AR) bandwidth at phi = 0 ° and theta = 35 ° of about 30.1% (4.97-6.73 GHz). Compared with the earlier reported conical-beam CP antennas, an important feature of the proposed antenna is that the AR bandwidth is completely included in the impedance bandwidth, that is, the overlap bandwidth of ∣ S 11 ∣ < − 10   dB and AR < 3   dB is 30.1%. Moreover, the stable omnidirectional conical-beam radiation patterns can be maintained within the whole operational bandwidth.

Slot loaded EBG-based metasurface for performance improvement of circularly polarized antenna for WiMAX applications

2019 ◽  
Vol 12 (3) ◽  
pp. 212-220 ◽  
Author(s):  
Alka Verma ◽  
Anil Kumar Singh ◽  
Neelam Srivastava ◽  
Shilpee Patil ◽  
Binod Kumar Kanaujia
Keyword(s):  
Performance Improvement ◽  
Coplanar Waveguide ◽  
Axial Ratio ◽  
Impedance Bandwidth ◽  
Compact Structure ◽  
Circularly Polarized ◽  
Feed Line ◽  
Rectangular Patch ◽  
Low Profile ◽  
Good Agreement

AbstractIn this paper, an electromagnetic band gap (EBG) metasurface (MS) superstrate-based circularly polarized antenna for the WiMAX (3.5 GHz) band is proposed. The proposed structure comprises a 2 × 2 slot-loaded rectangular patch MS array that can be perceived as a polarization-dependent EBG MS superstrate. Furthermore, to achieve circular polarization, the proposed antenna has an inclined coupling slot onto the ground with a conventional coplanar waveguide feed line. The proposed antenna has a compact structure with a low profile of 0.037λ0 (λ0 stands for the free-space wavelength at 3.48 GHz) and a ground size of 30 × 30 mm2. The measured results show that the −10 dB impedance bandwidth for the proposed antenna is 34.6% and the 3-dB axial ratio (AR) bandwidth is 6.8% with a peak gain of 3.91 dBi in the desired operating band. Good agreement between the simulated and the measured results verifies the performance of the proposed antenna.

scholarly journals Bandwidth-Enhanced Circularly Polarized Crescent-Shaped Slot Antenna via Circular-Patch Loading

2019 ◽  
Vol 9 (6) ◽  
pp. 1117 ◽  
Author(s):  
Son Trinh-Van ◽  
Youngoo Yang ◽  
Kang-Yoon Lee ◽  
Yong Kim ◽  
Keum Hwang
Keyword(s):  
Axial Ratio ◽  
Slot Antenna ◽  
Proper Position ◽  
Circularly Polarized ◽  
Circular Patch ◽  
Feed Line ◽  
Measurement Results ◽  
Patch Loading ◽  
Good Agreement ◽  
Microstrip Feed

This paper presents the crescent-shaped slot antenna loading of a circular patch that greatly enhances a 3 dB axial-ratio (AR) bandwidth. A bent feeding line was introduced and attached to a 50- Ω microstrip feed line to achieve circular polarization operation. By loading the circular patch into a crescent-shaped slot at a proper position, the 3 dB AR bandwidth is considerably broadened. An antenna prototype with overall dimensions of 50.8 × 50.8 × 0.5 mm 3 is experimentally demonstrated. Measurement results of the fabricated antenna showed a wide −10 dB reflection bandwidth of 92.33% (1.79–4.86 GHz) and a broad 3 dB AR bandwidth of 84.40% (1.89–4.65 GHz). The measured peak gain of the antenna was approximately 4.09 dBic at 2.9 GHz. Good agreement was also achieved between measurement and simulation results.

A compact, dual wide-band circularly polarized, modified square ring slot antenna for C and Ku band applications

2018 ◽  
Vol 11 (2) ◽  
pp. 182-189 ◽  
Author(s):  
Shilpee Patil ◽  
Anil Kumar Singh ◽  
Binod Kumar Kanaujia ◽  
R. L. Yadava
Keyword(s):  
Ground Plane ◽  
Simulated Data ◽  
Axial Ratio ◽  
Wide Band ◽  
Radiation Characteristic ◽  
Dual Band ◽  
Slot Antenna ◽  
Center Frequency ◽  
Impedance Bandwidth ◽  
Circularly Polarized

AbstractThis paper presents a compact microstrip antenna using FR-4 substrate for dual band circularly polarized operation using a modified square ring slot in the ground plane with microstrip line feed. Simulation of the impedance characteristic and radiation characteristic for the proposed antenna is carried out using commercially available HFSS software. The simulated data validate measured results and shows good agreement. Proposed antenna shows an impedance bandwidth (return loss >10 dB) of 50.88% at 5.9 GHz of center frequency and 29.92% at 12.8 GHz of center frequency for lower and upper band, respectively. The 3 dB axial ratio bandwidth for lower and upper band is 26.4 and 3.0%, respectively and measured peak gain for the lower and upper band is found as 3.2 and 3.4 dBic, respectively. The proposed antenna can be suitable for wireless communication in C and Ku bands.

Sign in / Sign up

Export Citation Format

Share Document