scholarly journals Modular waveguide filter platform for educational and prototyping purposes

2021 ◽  
pp. 1-10
Author(s):  
Daniel Miek ◽  
Daniel Bruhn ◽  
Kennet Braasch ◽  
Fynn Kamrath ◽  
Patrick Boe ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Frequency Dependent ◽  
Transmission Zeros ◽  
Waveguide Filter ◽  
Set Up ◽  
Chebyshev Filters

Abstract In this paper, a modular waveguide filter platform suitable for educational and prototyping purposes is presented. The waveguide filter platform is dimensioned to work in the F-band (4.9–7.05 GHz). The design of the platform is discussed and versatile application possibilities are shown in many examples. The platform can be used to realize generalized Chebyshev filters with or without cross-couplings by exploiting TE101 and TE102 mode cavities. Transmission zeros can be introduced by the utilization of wires or aperture couplings. Filter topologies based on the extracted pole technique can be examined as well. Small changes in the set-up also allow the realization of a gap waveguide filter, a diplexer set-up as well as filters with frequency-dependent coupling apertures. Most required components can either be purchased cheaply or be manufactured with a three-dimensional printer.

scholarly journals Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098705
Author(s):  
Xinran Wang ◽  
Yangli Zhu ◽  
Wen Li ◽  
Dongxu Hu ◽  
Xuehui Zhang ◽  
...  
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Element Model ◽  
Rotor System ◽  
Dynamic Responses ◽  
System Response ◽  
Rotating Speed ◽  
Torque Load ◽  
Set Up ◽  
Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

Optimum Design for the Frame of Open Type Abrasive Flow Polish Machine

2012 ◽  
Vol 497 ◽  
pp. 89-93
Author(s):  
Liang Liang Yuan ◽  
Ke Hua Zhang ◽  
Li Min
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Finite Element Methods ◽  
Optimization Design ◽  
Low Cost ◽  
Three Dimensional ◽  
Force Model ◽  
Optimization Analysis ◽  
Open Type ◽  
Set Up

In order to process heterotype hole of workpiece precisely, an open abrasive flow polish machine is designed, and the optimization design of machine frame is done for low cost. Firstly, basing on the parameters designed with traditional ways, three-dimensional force model is set up with the soft of SolidWorks. Secondly, the statics and modal analysis for machine body have been done in Finite element methods (FEM), and then the optimization analysis of machine frame has been done. At last, the model of rebuild machine frame has been built. Result shows that the deformation angle value of machine frame increased from 0.72′ to 1.001′, the natural frequency of the machine decreased from 75.549 Hz to 62.262 Hz, the weight of machine decreased by 74.178 Kg after optimization. It meets the strength, stiffness and angel stiffness requirement of machine, reduces the weight and cost of machine.

scholarly journals Computer-aided design of multi-purpose steel headframes for mines with a new technical level

2020 ◽  
Vol 174 ◽  
pp. 01048
Author(s):  
Elena Kassikhina ◽  
Vladimir Pershin ◽  
Nina Rusakova
Keyword(s):  
Cross Sections ◽  
Computer Aided Design ◽  
Information Technologies ◽  
Three Dimensional ◽  
Numerical Control ◽  
Technical Level ◽  
Resource Saving ◽  
Existing Structures ◽  
Set Up ◽  
Aided Design

The existing structures of the steel sinking headgear and permanent headframe do not meet the requirements of resource saving (metal consumption and manpower input at installation), and the present methods of the headframe designing do not fully reflect recent possibilities of applying of the advanced information technologies. Technical level of the modern software makes it possible for designers to set up multiple numerical experiments to create a computer simulation that allows solving the problem without field and laboratory experiments, and therefore without special costs. In this regard, a mathematical simulation has been developed and based on it, software to select cross-sections of multi- purpose steel headframe elements and to calculate proper weight of its metal structures depending on the characteristics and hoisting equipment. A headframe drawing is displayed, as the results of the software work, including list of elements, obtained optimal hoisting equipment in accordance with the initial data. The software allows speeding up graphic work and reducing manpower input on calculations and paper work. The software allows developing a three-dimensional image of the structure and its functional blocks, based on the obtained initial parameters, as well as developing control software for units with numerical control (NC) in order to manufacture multi-purpose headframes.

scholarly journals Novel Hexagonal Dual-Mode Substrate Integrated Waveguide Filter with Source-Load Coupling

2014 ◽  
Vol 2014 ◽  
pp. 1-5
Author(s):  
Ziqiang Xu ◽  
Gen Zhang ◽  
Hong Xia ◽  
Meijuan Xu
Keyword(s):  
Center Frequency ◽  
Substrate Integrated Waveguide ◽  
Fractional Bandwidth ◽  
Dual Mode ◽  
Transmission Zeros ◽  
Cavity Structure ◽  
Waveguide Filter ◽  
And Performance ◽  
Single Cavity ◽  
Good Agreement

Hexagonal dual-mode cavity and its application to substrate integrated waveguide (SIW) filter are presented. The hexagonal SIW resonator which can combine flexibility of rectangular cavity and performance of circular cavity is convenient for dual-mode bandpass filters design. By introducing coupling between source and load, the filter not only has good selectivity due to two controllable transmission zeros, but also has a small size by the virtue of its single-cavity structure. A demonstration filter with a center frequency of 10 GHz and a 3 dB fractional bandwidth of 4% is designed and fabricated to validate the proposed structure. Measured results are in good agreement with simulated ones.

Study on Magnetic Barrel Machine Equipped with Three-Dimensional Arrangement of Magnets

2007 ◽  
Vol 329 ◽  
pp. 761-766 ◽  
Author(s):  
Y. Zhang ◽  
Masato Yoshioka ◽  
Shin-Ichiro Hira
Keyword(s):  
High Speed ◽  
Permanent Magnets ◽  
Three Dimensional ◽  
Video Camera ◽  
High Speed Video ◽  
High Speed Video Camera ◽  
The Media ◽  
Set Up

At present, a commercially available magnetic barrel machine equipped with permanent magnets has some faults arising from constructional reason. That is, grinding or finishing ability is different from place to place in the machining region, resulting in the limitation on the region we can use in the container of workpieces. Therefore, in this research, authors made the new magnetic barrel machine equipped with three dimensional (3D) magnet arrangement to overcome these faults. The grinding ability of the new 3D magnetic barrel machine converted was experimentally examined, and compared with that of the traditional magnetic barrel machine. As a result, it was shown that we can use much broader region in the new 3D machine. It was also shown that the grinding ability became higher. The distribution of barrel media in action was recorded by means of a high speed video camera. It was clarified that the media rose up higher and were distributed more uniformly in the container by the effect of the magnet block newly set up. It was supposed that this must be the reason for the above-mentioned improvement of grinding ability.

Exploring Nature's plasticity with a flexible probing tool, and finding new ways for its electronic distribution

2002 ◽  
Vol 30 (2) ◽  
pp. 78-82 ◽  
Author(s):  
M. Beier ◽  
M. Baum ◽  
H. Rebscher ◽  
R. Mauritz ◽  
A. Wixmerten ◽  
...  
Keyword(s):  
Three Dimensional ◽  
In Situ Synthesis ◽  
Light Modulation ◽  
Genomic Assays ◽  
Electronic Distribution ◽  
Spatial Light Modulation ◽  
Microarray Fabrication ◽  
Set Up ◽  
Microarray Format

Concepts and results are described for the use of a single, but extremely flexible, probing tool to address a wide variety of genomic questions. This is achieved by transforming genomic questions into a software file that is used as the design scheme for potentially any genomic assay in a microarray format. Microarray fabrication takes place in three-dimensional microchannel reaction carriers by in situ synthesis based on spatial light modulation. This set-up allows for maximum flexibility in design and realization of genomic assays. Flexibility is achieved at the molecular, genomic and assay levels. We have applied this technology to expression profiling and genotyping experiments.

scholarly journals Assessing biases, relaxing moralism: On ground-truthing practices in machine learning design and application

2021 ◽  
Vol 8 (1) ◽  
pp. 205395172110135
Author(s):  
Florian Jaton
Keyword(s):  
Machine Learning ◽  
William James ◽  
A Priori ◽  
Learning Algorithms ◽  
Three Dimensional ◽  
Ground Truth ◽  
Machine Learning Algorithms ◽  
Ground Truthing ◽  
Set Up ◽  
The Moment

This theoretical paper considers the morality of machine learning algorithms and systems in the light of the biases that ground their correctness. It begins by presenting biases not as a priori negative entities but as contingent external referents—often gathered in benchmarked repositories called ground-truth datasets—that define what needs to be learned and allow for performance measures. I then argue that ground-truth datasets and their concomitant practices—that fundamentally involve establishing biases to enable learning procedures—can be described by their respective morality, here defined as the more or less accounted experience of hesitation when faced with what pragmatist philosopher William James called “genuine options”—that is, choices to be made in the heat of the moment that engage different possible futures. I then stress three constitutive dimensions of this pragmatist morality, as far as ground-truthing practices are concerned: (I) the definition of the problem to be solved (problematization), (II) the identification of the data to be collected and set up (databasing), and (III) the qualification of the targets to be learned (labeling). I finally suggest that this three-dimensional conceptual space can be used to map machine learning algorithmic projects in terms of the morality of their respective and constitutive ground-truthing practices. Such techno-moral graphs may, in turn, serve as equipment for greater governance of machine learning algorithms and systems.

scholarly journals Programmable nonreciprocal meta-prism

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Sajjad Taravati ◽  
George V. Eleftheriades
Keyword(s):  
Three Dimensional ◽  
Frequency Component ◽  
Phase Shifters ◽  
Frequency Dependent ◽  
Spatial Decomposition ◽  
Spatial Frequencies ◽  
Digitally Controlled ◽  
Field Programmable ◽  
Lorentz Reciprocity Theorem ◽  
Spatially Variant

AbstractOptical prisms are made of glass and map temporal frequencies into spatial frequencies by decomposing incident white light into its constituent colors and refract them into different directions. Conventional prisms suffer from their volumetric bulky and heavy structure and their material parameters are dictated by the Lorentz reciprocity theorem. Considering various applications of prisms in wave engineering and their growing applications in the invisible spectrum and antenna applications, there is a demand for compact apparatuses that are capable of providing prism functionality in a reconfigurable manner, with a nonreciprocal/reciprocal response. Here, we propose a nonreciprocal metasurface-based prism constituted of an array of phase- and amplitude-gradient frequency-dependent spatially variant radiating super-cells. In conventional optical prisms, nonreciprocal devices and metamaterials, the spatial decomposition and nonreciprocity functions are fixed and noneditable. Here, we present a programmable metasurface integrated with amplifiers to realize controllable nonreciprocal spatial decomposition, where each frequency component of the incident polychromatic wave can be transmitted under an arbitrary and programmable angle of transmission with a desired transmission gain. Such a polychromatic metasurface prism is constituted of frequency-dependent spatially variant transistor-based phase shifters and amplifiers for the spatial decomposition of the wave components. Interesting features include three-dimensional prism functionality with programmable angles of refraction, power amplification, and directive and diverse radiation beams. Furthermore, the metasurface prism can be digitally controlled via a field- programmable gate array (FPGA), making the metasurface a suitable solution for radars, holography applications, and wireless telecommunication systems.

Sign in / Sign up

Export Citation Format

Share Document