scholarly journals NEMA Performance Evaluation of CareMiBrain dedicated brain PET and Comparison with the whole-body and dedicated brain PET systems

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Laura Moliner ◽  
Maria J. Rodríguez-Alvarez ◽  
Juan V. Catret ◽  
Antonio González ◽  
Víctor Ilisie ◽  
...  
Keyword(s):  
Image Quality ◽  
Spatial Resolution ◽  
Performance Studies ◽  
System Performance ◽  
Full Width Half Maximum ◽  
Whole Body ◽  
Silicon Photomultipliers ◽  
Scatter Fraction ◽  
Brain Pet ◽  
Quality Study

Abstract This article presents system performance studies of the CareMiBrain dedicated brain PET according to NEMA NU 2-2012 (for whole-body PETs) and NU 4-2008 (for preclinical PETs). This scanner is based on monolithic LYSO crystals coupled to silicon photomultipliers. The results obtained for both protocols are compared with current commercial whole body PETs and dedicated brain PETs found in the literature. Spatial resolution, sensitivity, NECR and scatter-fraction are characterized with NEMA standards, as well as an image quality study. A customized image quality phantom is proposed as NEMA phantoms do not fulfil the necessities of dedicated brain PETs. The full-width half maximum of the radial/tangential/axial spatial resolution of CareMiBrain reconstructed with FBP at 10 and 100 mm from the system center were, respectively, 1.87/1.68/1.39 mm and 1.86/1.91/1.40 mm (NU 2-2012) and 1.58/1.45/1.40 mm and 1.64/1.66/1.44 mm (NU 4-2008). Peak NECR was 49 kcps@287 MBq with a scatter fraction of 48% using NU 2-2012 phantom. The sensitivity was 13.82 cps/kBq at the center of the FOV (NU 2-2012) and 10% (NU 4-2008). Contrast recovery coefficients for customizing image quality phantom were 0.73/0.78/1.14/1.01 for the 4.5/6/9/12 mm diameter rods. The performance characteristics of CareMiBrain are at the top of the current technologies for PET systems. Dedicated brain PET systems significantly improve spatial resolution and sensitivity, but present worse results in count rate measurements and scatter-fraction tests. As for the comparison of preclinical and clinical standards, the results obtained for solid and liquid sources were similar.

scholarly journals Threshold-dependent iodine imaging and spectral separation in a whole-body photon-counting CT system

2021 ◽  
Author(s):  
S. Sawall ◽  
L. Klein ◽  
E. Wehrse ◽  
L. T. Rotkopf ◽  
C. Amato ◽  
...  
Keyword(s):  
Image Quality ◽  
Photon Counting ◽  
Dual Energy ◽  
Whole Body ◽  
Dual Energy Ct ◽  
Post Mortem ◽  
Tube Voltage ◽  
Spectral Separation ◽  
Dual Source ◽  
Noise Ratio

Abstract Objective To evaluate the dual-energy (DE) performance and spectral separation with respect to iodine imaging in a photon-counting CT (PCCT) and compare it to dual-source CT (DSCT) DE imaging. Methods A semi-anthropomorphic phantom extendable with fat rings equipped with iodine vials is measured in an experimental PCCT. The system comprises a PC detector with two energy bins (20 keV, T) and (T, eU) with threshold T and tube voltage U. Measurements using the PCCT are performed at all available tube voltages (80 to 140 kV) and threshold settings (50–90 keV). Further measurements are performed using a conventional energy-integrating DSCT. Spectral separation is quantified as the relative contrast media ratio R between the energy bins and low/high images. Image noise and dose-normalized contrast-to-noise ratio (CNRD) are evaluated in resulting iodine images. All results are validated in a post-mortem angiography study. Results R of the PC detector varies between 1.2 and 2.6 and increases with higher thresholds and higher tube voltage. Reference R of the EI DSCT is found as 2.20 on average overall phantoms. Maximum CNRD in iodine images is found for T = 60/65/70/70 keV for 80/100/120/140 kV. The highest CNRD of the PCCT is obtained using 140 kV and is decreasing with decreasing tube voltage. All results could be confirmed in the post-mortem angiography study. Conclusion Intrinsically acquired DE data are able to provide iodine images similar to conventional DSCT. However, PCCT thresholds should be chosen with respect to tube voltage to maximize image quality in retrospectively derived image sets. Key Points • Photon-counting CT allows for the computation of iodine images with similar quality compared to conventional dual-source dual-energy CT. • Thresholds should be chosen as a function of the tube voltage to maximize iodine contrast-to-noise ratio in derived image sets. • Image quality of retrospectively computed image sets can be maximized using optimized threshold settings.

scholarly journals Fully digital PET is unaffected by any deterioration in TOF resolution and TOF image quality in the wide range of routine PET count rates

2021 ◽  
Vol 8 (1) ◽  
Author(s):  
Julien Salvadori ◽  
Freddy Odille ◽  
Gilles Karcher ◽  
Pierre-Yves Marie ◽  
Laetitia Imbert
Keyword(s):  
Image Quality ◽  
Dead Time ◽  
Silicon Photomultipliers ◽  
Timing Resolution ◽  
Upper Limits ◽  
Wide Range ◽  
Pile Up ◽  
Digital Pet ◽  
Trigger Circuit

Abstract Purpose Digital PET involving silicon photomultipliers (SiPM) provides an enhanced time-of-flight (TOF) resolution as compared with photomultiplier (PMT)-based PET, but also a better prevention of the count-related rises in dead time and pile-up effects mainly due to smaller trigger domains (i.e., the detection surfaces associated with each trigger circuit). This study aimed to determine whether this latter property could help prevent against deteriorations in TOF resolution and TOF image quality in the wide range of PET count rates documented in clinical routine. Methods Variations, according to count rates, in timing resolution and in TOF-related enhancement of the quality of phantom images were compared between the first fully digital PET (Vereos) and a PMT-based PET (Ingenuity). Single-count rate values were additionally extracted from the list-mode data of routine analog- and digital-PET exams at each 500-ms interval, in order to determine the ranges of routine PET count rates. Results Routine PET count rates were lower for the Vereos than for the Ingenuity. For Ingenuity, the upper limits were estimated at approximately 21.7 and 33.2 Mcps after injection of respectively 3 and 5 MBq.kg-1 of current 18F-labeled tracers. At 5.8 Mcps, corresponding to the lower limit of the routine count rates documented with the Ingenuity, timing resolutions provided by the scatter phantom were 326 and 621 ps for Vereos and Ingenuity, respectively. At higher count rates, timing resolution was remarkably stable for Vereos but exhibited a progressive deterioration for Ingenuity, respectively reaching 732 and 847 ps at the upper limits of 21.7 and 33.2 Mcps. The averaged TOF-related gain in signal/noise ratio was stable at approximately 2 for Vereos but decreased from 1.36 at 5.8 Mcps to 1.14 and 1.00 at respectively 21.7 and 33.2 Mcps for Ingenuity. Conclusion Contrary to the Ingenuity PMT-based PET, the Vereos fully digital PET is unaffected by any deterioration in TOF resolution and consequently, in the quality of TOF images, in the wide range of routine PET count rates. This advantage is even more striking with higher count-rates for which the preferential use of digital PET should be further recommended (i.e., dynamic PET recording, higher injected activities).

scholarly journals Simulated Radiation Dose Reduction in Whole-Body CT on a 3rd Generation Dual-Source Scanner: An Intraindividual Comparison

Diagnostics ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 118
Author(s):  
Andreas S. Brendlin ◽  
Moritz T. Winkelmann ◽  
Phuong Linh Do ◽  
Vincent Schwarze ◽  
Felix Peisen ◽  
...  
Keyword(s):  
Image Quality ◽  
Radiation Dose ◽  
Dose Reduction ◽  
Whole Body ◽  
Reference Standard ◽  
Diagnostic Confidence ◽  
Effective Radiation Dose ◽  
Intraindividual Comparison ◽  
Dual Source ◽  
Effective Radiation

To evaluate the effect of radiation dose reduction on image quality and diagnostic confidence in contrast-enhanced whole-body computed tomography (WBCT) staging. We randomly selected March 2016 for retrospective inclusion of 18 consecutive patients (14 female, 60 ± 15 years) with clinically indicated WBCT staging on the same 3rd generation dual-source CT. Using low-dose simulations, we created data sets with 100, 80, 60, 40, and 20% of the original radiation dose. Each set was reconstructed using filtered back projection (FBP) and Advanced Modeled Iterative Reconstruction (ADMIRE®, Siemens Healthineers, Forchheim, Germany) strength 1–5, resulting in 540 datasets total. ADMIRE 2 was the reference standard for intraindividual comparison. The effective radiation dose was calculated using commercially available software. For comparison of objective image quality, noise assessments of subcutaneous adipose tissue regions were performed automatically using the software. Three radiologists blinded to the study evaluated image quality and diagnostic confidence independently on an equidistant 5-point Likert scale (1 = poor to 5 = excellent). At 100%, the effective radiation dose in our population was 13.3 ± 9.1 mSv. At 20% radiation dose, it was possible to obtain comparably low noise levels when using ADMIRE 5 (p = 1.000, r = 0.29). We identified ADMIRE 3 at 40% radiation dose (5.3 ± 3.6 mSv) as the lowest achievable radiation dose with image quality and diagnostic confidence equal to our reference standard (p = 1.000, r > 0.4). The inter-rater agreement for this result was almost perfect (ICC ≥ 0.958, 95% CI 0.909–0.983). On a 3rd generation scanner, it is feasible to maintain good subjective image quality, diagnostic confidence, and image noise in single-energy WBCT staging at dose levels as low as 40% of the original dose (5.3 ± 3.6 mSv), when using ADMIRE 3.

scholarly journals Synthetic Aperture Imaging Using High-Frequency Convex Array for Ophthalmic Ultrasound Applications

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2275
Author(s):  
Hae Gyun Lim ◽  
Hyung Ham Kim ◽  
Changhan Yoon
Keyword(s):  
Image Quality ◽  
Penetration Depth ◽  
Spatial Resolution ◽  
High Frequency ◽  
Imaging System ◽  
Ex Vivo ◽  
Synthetic Aperture ◽  
Single Element ◽  
High Frequency Ultrasound ◽  
Synthetic Aperture Imaging

High-frequency ultrasound (HFUS) imaging has emerged as an essential tool for pre-clinical studies and clinical applications such as ophthalmic and dermatologic imaging. HFUS imaging systems based on array transducers capable of dynamic receive focusing have considerably improved the image quality in terms of spatial resolution and signal-to-noise ratio (SNR) compared to those by the single-element transducer-based one. However, the array system still suffers from low spatial resolution and SNR in out-of-focus regions, resulting in a blurred image and a limited penetration depth. In this paper, we present synthetic aperture imaging with a virtual source (SA-VS) for an ophthalmic application using a high-frequency convex array transducer. The performances of the SA-VS were evaluated with phantom and ex vivo experiments in comparison with the conventional dynamic receive focusing method. Pre-beamformed radio-frequency (RF) data from phantoms and excised bovine eye were acquired using a custom-built 64-channel imaging system. In the phantom experiments, the SA-VS method showed improved lateral resolution (>10%) and sidelobe level (>4.4 dB) compared to those by the conventional method. The SNR was also improved, resulting in an increased penetration depth: 16 mm and 23 mm for the conventional and SA-VS methods, respectively. Ex vivo images with the SA-VS showed improved image quality at the entire depth and visualized structures that were obscured by noise in conventional imaging.

Image-quality metrics for characterizing adaptive optics system performance

1997 ◽  
Vol 36 (26) ◽  
pp. 6583 ◽  
Author(s):  
Robert T. Brigantic ◽  
Michael C. Roggemann ◽  
Kenneth W. Bauer ◽  
Byron M. Welsh
Keyword(s):  
Image Quality ◽  
Adaptive Optics ◽  
System Performance ◽  
Quality Metrics ◽  
Image Quality Metrics ◽  
Adaptive Optics System

Deep learning-accelerated T2-weighted imaging of the prostate: impact of further acceleration with lower spatial resolution on image quality

2021 ◽  
pp. 110012
Author(s):  
Eu Hyun Kim ◽  
Moon Hyung Choi ◽  
Young Joon Lee ◽  
Dongyeob Han ◽  
Mahmoud Mostapha ◽  
...  
Keyword(s):  
Deep Learning ◽  
Image Quality ◽  
Spatial Resolution

Quantitative image quality evaluation method for UDC (Under Display Camera)

2021 ◽  
Keyword(s):  
Image Quality ◽  
International Symposium ◽  
System Performance ◽  
Quality Evaluation ◽  
Fast Track ◽  
Evaluation Method ◽  
Image Quality Evaluation ◽  
Electronic Imaging ◽  
Quantitative Image

Fast track article for IS&T International Symposium on Electronic Imaging 2021: Image Quality and System Performance XVIII proceedings.

scholarly journals Image Quality Differences In CT Scan Thorax By Using Slice Thickness Variation

2017 ◽  
Vol 8 (2) ◽  
pp. 87-91
Author(s):  
Samsun Samsun ◽  
Legia Prananto ◽  
Novita Wulandari
Keyword(s):  
Image Quality ◽  
Ct Scan ◽  
Spatial Resolution ◽  
Optimal Parameter ◽  
Thickness Variation ◽  
Slice Thickness ◽  
Picture Quality ◽  
Thorax Ct ◽  
Research Show ◽  
Selection Of

The picture quality get from CT Scan of Thorax which required optimal parameter selection that’s right, one of them the selection of slice thickness. The method taken from theses that have been publish in the year 2013. The results of the research show the percentage of the value of the average spatial resolution of 2.5 mm slice thickness is (33.3%), noise (17.8%), artefact (1%). On the thickness of the slices 5 mm spatial resolution is (17%), noise (8.9%), artefacts (0%). On the thickness of slices of 7.5 mm spatial resolution is (8.9%), noise (11.1%), artefacts (53.3%). While the thickness of the slices the spatial resolution is 10 mm (8.9%), noise (22.2%), artefacts (68.9%). Based on the research results obtained the conclusion that thickness 2.5 mm slices on Thorax CT-Scan images produce better picture quality than with the thickness of the slices 5 mm, 7.5 mm, 10 mm, because the spatial resolution is more clear so as to reduce noise and artifacts.

Sign in / Sign up

Export Citation Format

Share Document