scholarly journals A 300-GHz low-cost high-gain fully metallic Fabry–Perot cavity antenna for 6G terahertz wireless communications

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Basem Aqlan ◽  
Mohamed Himdi ◽  
Hamsakutty Vettikalladi ◽  
Laurent Le-Coq
Keyword(s):  
Communication Systems ◽  
Low Cost ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Wireless Communication Systems ◽  
Beam Radiation ◽  
Compact Size ◽  
Fabry Perot ◽  
Operating Bandwidth ◽  
Polarization Level

AbstractA low-cost, compact, and high gain Fabry–Perot cavity (FPC) antenna which operates at 300 GHz is presented. The antenna is fabricated using laser-cutting brass technology. The proposed antenna consists of seven metallic layers; a ground layer, an integrated stepped horn element (three-layers), a coupling layer, a cavity layer, and an aperture-frequency selective surface (FSS) layer. The proposed aperture-FSS function acts as a partially reflective surface, contributing to a directive beam radiation. For verification, the proposed sub-terahertz (THz) FPC antenna prototype was developed, fabricated, and measured. The proposed antenna has a measured reflection coefficient below − 10 dB from 282 to 304 GHz with a bandwidth of 22 GHz. The maximum measured gain observed is 17.7 dBi at 289 GHz, and the gain is higher than 14.4 dBi from 285 to 310 GHz. The measured radiation pattern shows a highly directive pattern with a cross-polarization level below − 25 dB over the whole band in all cut planes, which confirms with the simulation results. The proposed antenna has a compact size, low fabrication cost, high gain, and wide operating bandwidth. The total height of the antenna is 1.24 $${\lambda }_{0}$$ λ 0 ($${\lambda }_{0}$$ λ 0 at the design frequency, 300 GHz) , with a size of 2.6 mm × 2.6 mm. The proposed sub-THz waveguide-fed FPC antenna is suitable for 6G wireless communication systems.

scholarly journals A Broadband High-Gain Printed Antenna Array Using Dipole and Loop Patches for 5G Communication Systems

2021 ◽  
Vol 15 ◽  
pp. 42-45
Author(s):  
Yuanzhi Liu ◽  
Mustapha C.E. Yagoub
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Low Cost ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Wave Band ◽  
Printed Antenna ◽  
Compact Size ◽  
5G Communication

A broadband and high-gain printed antenna array is presented in this paper. Its single antenna element consists of a loop and two symmetric dipole patches, making the element exhibiting broad impedance bandwidth and improved gain at the targeted frequency, which is 28 GHz, one of the 5G mm-wave band, for this design. An 8×3 antenna array fed by a microstrip line feed network was designed and simulated. With a compact size of 98×32.5 mm2 , the array presents a broad -10 dB impedance bandwidth of 6.8 GHz (24.3%) and a high gain of 18 dBi at 28 GHz. Besides, the single-layered array also features low profile, simple geometry, and low cost, making it a good candidate for 5G communication systems.

scholarly journals Physical-Layer Security Improvement with Reconfigurable Intelligent Surfaces for 6G Wireless Communication Systems

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1439
Author(s):  
Janghyuk Youn ◽  
Woong Son ◽  
Bang Chul Jung
Keyword(s):  
Wireless Communication ◽  
Physical Layer Security ◽  
Communication Systems ◽  
Low Cost ◽  
Physical Layer ◽  
Base Station ◽  
Wireless Communication Systems ◽  
Secrecy Rate ◽  
Pilot Signal ◽  
Time Division

Recently, reconfigurable intelligent surfaces (RISs) have received much interest from both academia and industry due to their flexibility and cost-effectiveness in adjusting the phase and amplitude of wireless signals with low-cost passive reflecting elements. In particular, many RIS-aided techniques have been proposed to improve both data rate and energy efficiency for 6G wireless communication systems. In this paper, we propose a novel RIS-based channel randomization (RCR) technique for improving physical-layer security (PLS) for a time-division duplex (TDD) downlink cellular wire-tap network which consists of a single base station (BS) with multiple antennas, multiple legitimate pieces of user equipment (UE), multiple eavesdroppers (EVEs), and multiple RISs. We assume that only a line-of-sight (LOS) channel exists among the BS, the RISs, and the UE due to propagation characteristics of tera-hertz (THz) spectrum bands that may be used in 6G wireless communication systems. In the proposed technique, each RIS first pseudo-randomly generates multiple reflection matrices and utilizes them for both pilot signal duration (PSD) in uplink and data transmission duration (DTD) in downlink. Then, the BS estimates wireless channels of UE with reflection matrices of all RISs and selects the UE that has the best secrecy rate for each reflection matrix generated. It is shown herein that the proposed technique outperforms the conventional techniques in terms of achievable secrecy rates.

Design and fabrication of a high gain, low cost, LHCP Fabry‐Perot antenna at Ku band

2018 ◽  
Vol 61 (1) ◽  
pp. 101-106 ◽  
Author(s):  
Yousef Azizi ◽  
Nader Komjani ◽  
Majid Karimipour
Keyword(s):  
Low Cost ◽  
High Gain ◽  
Fabry Perot ◽  
Ku Band

scholarly journals Omnidirectional Microstrip Patch Antenna for 2.4 GHz Wireless Communications

2021 ◽  
Vol 2114 (1) ◽  
pp. 012051
Author(s):  
Alaa M. Abdulhussein ◽  
Ali H. Khidhi ◽  
Ahmed A. Naser
Keyword(s):  
Computer Simulation ◽  
Wireless Communications ◽  
Wireless Communication ◽  
Patch Antenna ◽  
Communication Systems ◽  
Return Loss ◽  
Microstrip Patch Antenna ◽  
Wireless Communication Systems ◽  
Microstrip Patch ◽  
Operating Bandwidth

Abstract Antenna studies on various wireless communication systems have been carried out by many academics. In this research, the omnidirectional microstrip patch antenna (MPA) is proposed, manufactured, and tested. The operating bandwidth of the antenna is quite suitable for the different applications. The proposed antenna fabricated on the flame retardant (FR-4) substrate with a volume of 75.85 × 57.23 × 1.59 mm3. Computer simulation technology (CST) studio used to design and simulate. Experimental results show that the return loss (RL), bandwidth (BW), voltage standing wave ratio (VSWR) and input impedance (Zin ) are -25.26 dB, 61 MHz, 1.12 and 54.46 Ω, respectively. The antenna operates at 2.42 GHz (from 2.39 to 2.45 GHz), which has good performance in the Wi-Fi, Bluetooth, and ZigBee communications.

scholarly journals A six-channel microstrip diplexer for multi-service wireless communication systems

2020 ◽  
Vol 41 (3) ◽  
Author(s):  
Farhad Fouladi ◽  
Abbas Rezaei
Keyword(s):  
Wireless Communication ◽  
Communication Systems ◽  
The Other ◽  
Wireless Communication Systems ◽  
Frequency Division ◽  
Compact Size ◽  
Coupled Lines ◽  
Simulation Results ◽  
Insertion Losses

In this paper, a six-channel microstrip diplexer is designed and fabricated. It operates at 0.75/0.85/1/1.25/1.6/1.8 GHz for multi-service wireless communication systems. It consists of two stub-loaded resonators, which are integrated by coupled lines. The channels are close together, which makes the proposed diplexer suitable for frequency division duplex (FDD) schemes. The proposed structure has a compact size of 0.025 λg2 where λg is the guided wavelength calculated at 0.75 GHz. The other advantages of the introduced multi-channel diplexer are the low insertion losses of 1.62/1.27/0.43/0.53/1.26 and 1 dB, as well as good return losses of 26/26/25/25/21.7 and 22 dB at 0.75/0.85/1/1.25/1.6/1.8 GHz respectively. A good isolation of less than 22 dB is obtained between the channels. In order to design the presented diplexer a designing technique is used which is based on the proposing of an equivalent approximated LC model and calculating the inductors and capacitors. To confirm the simulation results, the introduced diplexer is fabricated and measured.

Reconfigurable Antenna

2016 ◽  
pp. 237-263
Author(s):  
Mohamad Kamal A Rahim ◽  
Huda A. A. Majid ◽  
Mohamad Rijal Hamid
Keyword(s):  
Communication Systems ◽  
Low Cost ◽  
Wireless Systems ◽  
Reconfigurable Antennas ◽  
Effective Length ◽  
Slot Antenna ◽  
Wireless Communication Systems ◽  
Reconfigurable Antenna ◽  
5 Ghz ◽  
Narrow Bands

Reconfigurable antennas have attracted a lot of attention especially in future wireless communication systems. Superior features such as reconfigurable capability, low cost, multi-purpose functions and size miniaturization have given reconfigurable antennas advantage to be integrated into a wireless systems. In this chapter, two types of reconfigurable antennas are discussed. First, frequency reconfigurable narrowband microstrip slot antenna (FRSA) is presented. The proposed antenna is designed to operate at six reconfigurable frequency bands from 2 GHz to 5 GHz with bidirectional radiation pattern. The second antenna design is frequency reconfigurable narrowband patch-slot antenna (FRPSA) is presented. The antenna is a combination of a microstrip patch and slot antenna. Nine different narrow bands are produced by tuning the effective length of the slot. The performances of the antenna in term of simulated and measured results are presented. In conclusion, good agreement between the simulated and measured results has been attained.

scholarly journals A High-Isolation Dual-Polarization Substrate-Integrated Fabry-Pérot Cavity Antenna

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Chang Chen ◽  
Bo-Liang Liu ◽  
Ling Ji ◽  
Wei-Dong Chen
Keyword(s):  
Near Field ◽  
Ground Plane ◽  
Cross Polarization ◽  
Dual Polarization ◽  
High Isolation ◽  
Fabry Perot ◽  
Feeding Structure ◽  
Operating Bandwidth ◽  
High Degree ◽  
Polarization Level

A dual-polarization substrate-integrated Fabry-Pérot cavity (SI-FPC) antenna is presented in this paper. The patch embedded in SI-FPC is excited with a near-field coupled feeding structure for V-polarization and with a slot-coupled feeding structure for H-polarization. The feeding structures are separated by a ground plane to improve the isolation between the ports. As a design example, an antenna operating at 10.0 GHz is fabricated and measured. A high degree of port isolation (<−40 dB) over the whole operating bandwidth (9.5–10.2 GHz) and good cross-polarization level (>25 dB) can be achieved.

scholarly journals Design of a Substrate-Integrated Fabry-Pérot Cavity Antenna forK-Band Applications

2015 ◽  
Vol 2015 ◽  
pp. 1-12 ◽  
Author(s):  
Truong Khang Nguyen ◽  
Ikmo Park
Keyword(s):  
Coplanar Waveguide ◽  
Ground Plane ◽  
Cost Effective ◽  
Frequency Selective Surface ◽  
High Gain ◽  
Hole Array ◽  
Impedance Bandwidth ◽  
Low Profile ◽  
Fabry Perot ◽  
Feeding Structure

This paper presents the design of a planar, low-profile, high-gain, substrate-integrated Fabry-Pérot cavity antenna forK-band applications. The antenna consists of a frequency selective surface (FSS) and a planar feeding structure, which are both lithographically patterned on a high-permittivity substrate. The FSS is made of a circular hole array that acts as a partially reflecting mirror. The planar feeding structure is a wideband leaky-wave slit dipole fed by a coplanar waveguide whose ground plane acts as a perfect reflective mirror. The measured results show that the proposed antenna has an impedance bandwidth of more than 8% (VSWR ≤ 2), a maximum gain of 13.1 dBi, and a 3 dB gain bandwidth of approximately 1.3% at a resonance frequency of around 21.6 GHz. The proposed antenna features low-profile, easy integration into circuit boards, mechanical robustness, and excellent cost-effective mass production suitability.

Sign in / Sign up

Export Citation Format

Share Document