scholarly journals Comparison of a low transition temperature mixture (LTTM) formed by lactic acid and choline chloride with choline lactate ionic liquid and the choline chloride salt: physical properties and vapour–liquid equilibria of mixtures containing water and ethanol

RSC Advances ◽  
2013 ◽  
Vol 3 (45) ◽  
pp. 23553 ◽  
Author(s):  
María Francisco ◽  
Agustín S. B. González ◽  
Sara Lago García de Dios ◽  
Wilko Weggemans ◽  
Maaike C. Kroon
Keyword(s):  
Ionic Liquid ◽  
Lactic Acid ◽  
Transition Temperature ◽  
Physical Properties ◽  
Choline Chloride ◽  
Chloride Salt

scholarly journals Valorization of birch bark using a low transition temperature mixture composed of choline chloride and lactic acid

2021 ◽  
Vol 10 (1) ◽  
pp. 902-911
Author(s):  
Michal Jablonský ◽  
Jozef Šima ◽  
Petra Strižincová ◽  
Katarína Hroboňová ◽  
Veronika Majová ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Transition Temperature ◽  
Betulinic Acid ◽  
Phenolic Content ◽  
Choline Chloride ◽  
Polyphenolic Compounds ◽  
Molar Ratio ◽  
Total Phenolic ◽  
Birch Bark ◽  
Green Solvent

Abstract This article presents the results obtained in the extraction of birch bark with a green solvent. A low transition temperature mixture (LTTM) consisting of choline chloride (ChCl) and lactic acid in a molar ratio of 1:1 was used as the solvent. Extraction was performed at 60°C and 80°C. At both temperatures, the effect of extraction time on the yield of the extracted substances was monitored. The yields reached were compared with those obtained in studies using common solvents such as ethanol, methanol, d-limonene, ethyl acetate, and others. The extract was quantitatively analyzed by HPLC-UV to determine betulin and betulinic acid (0.491–1.788 mg/g dry bark and 0.106–0.316 mg/g dry bark, respectively). Total phenolic content was determined spectrometrically using Folin–Ciocalteu reagent and expressed as Gallic acid equivalents (GAE; 18.6–56.8 mg GAE/g dry bark). This study has shown that extraction with a green solvent composed of ChCl and lactic acid can be an effective method for extracting polyphenolic compounds from birch bark. The process for extracting triterpenes (betulin and betulinic acid) is less suitable compared to conventional methods using the mentioned organic extractants.

A new low transition temperature mixture (LTTM) formed by choline chloride+lactic acid: Characterization as solvent for CO2 capture

2013 ◽  
Vol 340 ◽  
pp. 77-84 ◽  
Author(s):  
María Francisco ◽  
Adriaan van den Bruinhorst ◽  
Lawien F. Zubeir ◽  
Cor J. Peters ◽  
Maaike C. Kroon
Keyword(s):  
Lactic Acid ◽  
Transition Temperature ◽  
Co2 Capture ◽  
Choline Chloride

A Novel Poly(Ionic Liquid) as the Thermal Insulating Material

2020 ◽  
Vol 13 (3) ◽  
pp. 241-247
Author(s):  
Wenxin Wei ◽  
Guifeng Ma ◽  
Hongtao Wang ◽  
Jun Li
Keyword(s):  
Thermal Conductivity ◽  
Ionic Liquid ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Flame Resistance ◽  
Insulating Material ◽  
Low Thermal Conductivity ◽  
Thermal Insulating ◽  
Poly Ionic Liquid

Objective: A new poly(ionic liquid)(PIL), poly(p-vinylbenzyltriphenylphosphine hexafluorophosphate) (P[VBTPP][PF6]), was synthesized by quaternization, anion exchange reaction, and free radical polymerization. Then a series of the PIL were synthesized at different conditions. Methods: The specific heat capacity, glass-transition temperature and melting temperature of the synthesized PILs were measured by differential scanning calorimeter. The thermal conductivities of the PILs were measured by the laser flash analysis method. Results: Results showed that, under optimized synthesis conditions, P[VBTPP][PF6] as the thermal insulator had a high glass-transition temperature of 210.1°C, high melting point of 421.6°C, and a low thermal conductivity of 0.0920 W m-1 K-1 at 40.0°C (it was 0.105 W m-1 K-1 even at 180.0°C). The foamed sample exhibited much low thermal conductivity λ=0.0340 W m-1 K-1 at room temperature, which was comparable to a commercial polyurethane thermal insulating material although the latter had a much lower density. Conclusion: In addition, mixing the P[VBTPP][PF6] sample into polypropylene could obviously increase the Oxygen Index, revealing its efficient flame resistance. Therefore, P[VBTPP][PF6] is a potential thermal insulating material.

scholarly journals Enhancing Pervaporation Membrane Selectivity by Incorporating Star Macromolecules Modified with Ionic Liquid for Intensification of Lactic Acid Dehydration

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1811
Author(s):  
Valeriia Rostovtseva ◽  
Alexandra Pulyalina ◽  
Roman Dubovenko ◽  
Ilya Faykov ◽  
Kseniya Subbotina ◽  
...  
Keyword(s):  
Ionic Liquid ◽  
Lactic Acid ◽  
Polymer Matrix ◽  
Separation Factor ◽  
Membrane Structure ◽  
High Performance ◽  
Separation Efficiency ◽  
Pharmaceutical Chemical ◽  
Permeate Flux ◽  
Membrane Components

Modification of polymer matrix by hybrid fillers is a promising way to produce membranes with excellent separation efficiency due to variations in membrane structure. High-performance membranes for the pervaporation dehydration were produced by modifying poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) to facilitate lactic acid purification. Ionic liquid (IL), heteroarm star macromolecules (HSM), and their combination (IL:HSM) were employed as additives to the polymer matrix. The composition and structure of hybrid membranes were characterized by X-ray diffraction and FTIR spectroscopy. Scanning electron microscopy was used to investigate the membranes surface and cross-section morphology. It was established that the inclusion of modifiers in the polymer matrix leads to the change of membrane structure. The influence of IL:HSM was also studied via sorption experiments and pervaporation of water‒lactic acid mixtures. Lactic acid is an essential compound in many industries, including food, pharmaceutical, chemical, while the recovering and purifying account for approximately 50% of its production cost. It was found that the membranes selectively remove water from the feed. Quantum mechanical calculations determine the favorable interactions between various membrane components and the liquid mixture. With IL:HSM addition, the separation factor and performance in lactic acid dehydration were improved compared with pure polymer membrane. The best performance was found for (HSM: IL)-PPO/UPM composite membrane, where the permeate flux and the separation factor of about 0.06 kg m−2 h−1 and 749, respectively, were obtained. The research results demonstrated that ionic liquids in combination with star macromolecules for membrane modification could be a promising approach for membrane design.

scholarly journals Study of physical properties of a ferrimagnetic spinel Cu1.5Mn1.5O4: spin dynamics, magnetocaloric effect and critical behavior

RSC Advances ◽  
2021 ◽  
Vol 11 (41) ◽  
pp. 25664-25676
Author(s):  
Abir Hadded ◽  
Jalel Massoudi ◽  
Sirine Gharbi ◽  
Essebti Dhahri ◽  
A. Tozri ◽  
...  
Keyword(s):  
Phase Transition ◽  
Transition Temperature ◽  
Physical Properties ◽  
Magnetocaloric Effect ◽  
Phase Transition Temperature ◽  
Magnetic Phase Transition ◽  
Critical Behavior ◽  
Magnetic Phase ◽  
Spin Dynamics ◽  
Critical Behaviour

The present work reports a detailed study of the spin dynamics, magnetocaloric effect and critical behaviour near the magnetic phase transition temperature, of a ferrimagnetic spinel Cu1.5Mn1.5O4.

Synthesis and Properties of Biodegradable Liquid Crystalline Poly(ester-Urethane)s Based on Poly(L-Lactic Acid)

2013 ◽  
Vol 652-654 ◽  
pp. 459-462
Author(s):  
Ya Tong Guo ◽  
Zhu Zheng ◽  
Zhen Qi Hou ◽  
Jie Du
Keyword(s):  
Phase Transition ◽  
Thermal Stability ◽  
Lactic Acid ◽  
Physical Properties ◽  
Liquid Crystalline ◽  
Degradation Rate ◽  
Hydrolytic Degradation ◽  
Hexamethylene Diisocyanate ◽  
Solution Polymerization ◽  
Phase Transition Temperatures

A series of biodegradable segmented liquid crystalline poly(ester-urethane)s were prepared by solution polymerization of poly(L-lactic acid) (PLLA), mesogenic diol prepolymer poly(butylene terephthaloyldioxy dibenzoates) (MD), and hexamethylene diisocyanate (HDI). The MD content was varied from 0 to 40 mol% so that the effects of the mesogen content on the thermal and physical properties, and hydrolytic degradation were examined respectively. It was found that introducing mesogens units could increase the thermal stability and the elastic properties, while reduced the phase transition temperatures and the hydrolytic degradation rate.

scholarly journals Esterification of Lignin Isolated by Deep Eutectic Solvent Using Fatty Acid Chloride, and Its Composite Film with Poly(lactic acid)

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2149
Author(s):  
Chan-Woo Park ◽  
Song-Yi Han ◽  
Rajkumar Bandi ◽  
Ramakrishna Dadigala ◽  
Eun-Ah Lee ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Fatty Acid ◽  
Composite Film ◽  
Acid Chloride ◽  
Pinus Densiflora ◽  
Choline Chloride ◽  
Deep Eutectic Solvent ◽  
Morphological Characteristics ◽  
Poly Lactic Acid ◽  
Fatty Acid Chloride

In this study, the effect of lignin esterification with fatty acid chloride on the properties of lignin and lignin/poly(lactic acid) (PLA) composites was investigated. Lignocellulose (Pinus densiflora S. et Z.) was treated using a deep eutectic solvent (DES) with choline chloride (ChCl)/lactic acid (LA). From the DES-soluble fraction, DES-lignin (DL) was isolated by a regeneration process. Lignin esterification was conducted with palmitoyl chloride (PC). As the PC loading increased for DL esterification, the Mw of esterified DL (EDL) was increased, and the glass transition temperature (Tg) was decreased. In DL or EDL/PLA composite films, it was observed that EDL/PLA had cleaner and smoother morphological characteristics than DL/PLA. The addition of DL or EDL in a PLA matrix resulted in a deterioration of tensile properties as compared with neat PLA. The EDL/PLA composite film had a higher tensile strength and elastic modulus than the DL/PLA composite film. DL esterification decreased water absorption with lower water diffusion coefficients. The effect of lignin esterification on improving the compatibility of lignin and PLA was demonstrated. These results are expected to contribute to the development of high-strength lignin composites.

scholarly journals Deep Eutectic Solvents Based Choline Chloride for Enzymatic Biodiesel Production from Degumming Palm Oil

2020 ◽  
Vol 32 (4) ◽  
pp. 733-738 ◽  
Author(s):  
R. Manurung ◽  
Taslim ◽  
A.G.A. Siregar
Keyword(s):  
Palm Oil ◽  
Raw Materials ◽  
Choline Chloride ◽  
Deep Eutectic Solvent ◽  
Deep Eutectic Solvents ◽  
Biodiesel Production ◽  
Chloride Salt ◽  
Enzymatic Reactions ◽  
Potential Applications ◽  
Palm Oil Biodiesel

Deep eutectic solvents (DESs) have numerous potential applications as cosolvents. In this study, use of DES as organic solvents for enzymatic biodiesel production from degumming palm oil (DPO) was investigated. Deep eutectic solvent was synthesized using choline chloride salt (ChCl) compounds with glycerol and 1,2-propanediol. Deep eutectic solvent was characterized by viscosity, density, pH and freezing values, which were tested for effectiveness by enzymatic reactions for the production of palm biodiesel with raw materials DPO. Deep eutectic solvent of ChCl and glycerol produced the highest biodiesel yield (98.98%); weight of DES was only 0.5 % of that of the oil. In addition, the use of DES maintained the activity and stability of novozym enzymes, which was assessed as the yield until the 6th usage, which was 95.07 % biodiesel yield compared with the yield without using DES. Hence, using DES, glycerol in enzymatic biodiesel production had high potentiality as an organic solvent for palm oil biodiesel production

Preparation of Poly(Lactic Acid) Acrylate for UV-Curable Coating Applications

2015 ◽  
Vol 659 ◽  
pp. 570-574 ◽  
Author(s):  
Apinya Musidang ◽  
Nantana Jiratumnukul
Keyword(s):  
Lactic Acid ◽  
Physical Properties ◽  
High Efficiency ◽  
Low Energy ◽  
Poly Lactic Acid ◽  
Coating Film ◽  
Pencil Hardness ◽  
Uv Curable ◽  
Low Energy Consumption ◽  
Volatile Organic

UV-curable process is widely used for paints, inks and adhesives due to its rapid curing, low energy consumption, high efficiency and low volatile organic compounds (VOCs). The objective of this research is to prepare poly(lactic acid) (PLA) based UV-curable coating by using glycolyzed PLA. PLA was glycolyzed by ethylene glycol (EG) at 170°C for 90 minutes. The obtained glycolyzed PLA was reacted with methacrylic anhydride (MAAH) to provide PLA acrylate oligomer. The obtained PLA acrylate oligomer was used in coating formulations with various amounts of photoinitiator and cured under UV radiation. Physical properties of cured coating film were investigated such as pencil hardness, gloss and haze. The results showed that poly(lactic acid) (PLA) based UV-curable coating provided good physical properties.

Sign in / Sign up

Export Citation Format

Share Document