scholarly journals Increasing the efficiency of diesel engines operation by changing the process of fuel injection into the combustion chamber

2021 ◽  
Vol 273 ◽  
pp. 07025
Author(s):  
Igor Ivanov
Keyword(s):  
Problem Solving ◽  
Combustion Chamber ◽  
Fuel Consumption ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Reduce Fuel Consumption ◽  
Constructive Solution

This paper proposes the author’s method of developing a constructive solution for supplying fuel to the combustion chamber to reduce fuel consumption in operation on the basis of TIPS (theory of inventive problem solving).

scholarly journals Injection and Combustion of RME with Water Emulsions in a Diesel Engine

10.14311/1169 ◽  
2010 ◽  
Vol 50 (2) ◽  
Author(s):  
J. Cisek
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Flow Reactor ◽  
Flame Temperature ◽  
Pressure Rise ◽  
Engine Performance ◽  
Exponential Relationship ◽  
Water Fraction

This paper presents ways of using the fully-digitised triggerable AVL VideoScope 513D video system for analysing the injection and combustion inside a diesel engine cylinder fuelled by RME with water emulsions.The research objects were: standard diesel fuel, rapeseed methyl ester (RME) and RME – water emulsions. With the aid of a helical flow reactor, stable emulsions with the water fraction up to 30 % weight were obtained, using an additive to prevent the water from separating out of the emulsion.An investigation was made of the effect of the emulsions on exhaust gas emissions (NOX, CO and HC), particulate matter emissions, smoke and the fuel consumption of a one-cylinder HD diesel engine with direct injection. Additionally, the maximum cylinder pressure rise was calculated from the indicator diagram. The test engine was operated at a constant speed of 1 600 rpm and 4 bar BMEP load conditions. The fuel injection and combustion processes were observed and analysed using endoscopes and a digital camera. The temperature distribution in the combustion chamber was analysed quantitatively using the two-colour method. The injection and combustion phenomena were described and compared.A way to reduce NOX formation in the combustion chamber of diesel engines by adding water in the combustion zone was presented. Evaporating water efficiently lowers the peak flame temperature and the temperature in the post-flame zone. For diesel engines, there is an exponential relationship between NOX emissions and peak combustion temperatures. The energy needed to vaporize the water results in lower peak temperatures of the combusted gases, with a consequent reduction in nitrogen oxide formation. The experimental results show up to 50 % NOX emission reduction with the use of 30% water in an RME emulsion, with unchanged engine performance.

scholarly journals Contributions to the study of service characteristics of marine fuels

2018 ◽  
Vol XIX (1) ◽  
pp. 502-508
Author(s):  
Ali L
Keyword(s):  
Fuel Consumption ◽  
International Organizations ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Cylinder Liner ◽  
Operating Mode ◽  
Service Characteristics ◽  
Marine Engines ◽  
Marine Diesel ◽  
A Priority

Since the beginning, development of marine diesel engines was turned towards obtaining a low fuel consumption and the result has reflected in engines construction: increased bore and cylinder liner diameter, higher working pressures and lower piston speeds. Similar improvements have taken place in the supercharging system, innovative fuel injection technologies and changes in combustion pressures. Nowadays, the trend of development has changed, the concept of reducing NOx and SOx emissions became a priority in order to meet the limits imposed by international organizations. As a consequence, a series of changes in operating mode of marine engines was noticed but also several innovations appeared in the construction and development of marine engines.

scholarly journals IMPROVING FUEL EFFICIENCY OF MARINE SWIRL-CHAMBER DIESEL ENGINE BY INCREASED THERMAL RESISTANCE OF HEAT TRANSFER

2019 ◽  
pp. 80-87
Author(s):  
Alexander Fedorovich Dorokhov ◽  
Pavel Aleksandrovitch Dorokhov
Keyword(s):  
Heat Transfer ◽  
Diesel Engine ◽  
Thermal Resistance ◽  
Combustion Chamber ◽  
Fuel Consumption ◽  
Diesel Engines ◽  
Fuel Efficiency ◽  
Working Fluid ◽  
Gas Temperature ◽  
Swirl Chamber

The article considers ship swirl-chamber diesel engines used in shipbuilding as the main and auxiliary engines. Two reasons for low profitability of the swirl chamber diesel engines are highlighted: large heat losses of the cooling working fluid due to the extended heat transfer surface of the chamber, and significant aerodynamic energy losses of compressed air during its passage through a relatively narrow channel connecting the piston chamber with the combustion chamber and the flow of gases from the swirl chamber on top the piston space. There have been proposed the methods for improving the operational performance of swirl-chamber diesels in production, in particular, their fuel efficiency. The scheme of the swirl-chamber and a section of the swirl-chamber cylinder head are presented. It has been stated that the total coefficient of thermal conductivity can be reduced if the wall of the swirl- chamber is made multi-layer. The layouts of a multi-layer cylinder-spherical wall of a swirl combustion chamber with a titanium cylinder-spherical insertion and thermal insulation of a vortex combustion chamber are given. The total thermal resistance of the spherical wall was calculated, heat loss through the multilayer spherical wall was determined, gas temperature in the vortex chamber was calculated, according to the average cycle temperature diagram. It was inferred that the amount of heat removed from the working fluid to cooling through the thermally insulated wall of the swirl-chamber will be 40% less than the amount of heat released to the cooling through the wall of the swirl-chamber of a commercial diesel engine. The difference in heat will be used to increase the indicator gas operation, which, with the same cyclic fuel supply, will lead to a decrease in the specific indicator fuel consumption, and at a constant level of internal engine losses - to a decrease in the specific effective fuel consumption.

Improvement of Emissions From Diesel Engines

1988 ◽  
Vol 110 (3) ◽  
pp. 343-348 ◽  
Author(s):  
T. Morimatsu ◽  
T. Okazaki ◽  
T. Furuya ◽  
H. Furukawa
Keyword(s):  
Mass Transfer ◽  
Combustion Chamber ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Air Entrainment ◽  
Injection Timing ◽  
Injection Pump ◽  
High Injection ◽  
High Injection Pressure

It is important to reduce emissions from diesel engines, which are used in the cogeneration systems. The mass transfer to the fuel spray plays various roles in fuel consumption rate and in trace species emission. High injection pressure and a re-entrant combustion chamber were used to make the mass transfer larger. The need for high injection pressure and controlled injection timing for NOx led the authors to use the new Komatsu fuel injection pump. This pump, which has a re-entrant combustion chamber, resulted in clean engine emissions and confirmed the importance of air entrainment to the spray.

Study on Different Flame Jet Ignition Variants in a Stratified Charge Spark Ignition Engine

2002 ◽  
Author(s):  
Edward Rakosi ◽  
Radu Rosca
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Output Power ◽  
Cylinder Head ◽  
Fuel Injection ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Working Process ◽  
Stratified Charge ◽  
Direct Fuel Injection

The paper presents some experimental results regarding a stratified charge spark ignition engine. We have applied the divided combustion chamber concept, using a flame jet in order to ignite the fuel-air mixture. The fueling system was a combined one: the cylinder head combustion chamber (secondary, auxiliary) was fueled by direct fuel injection, while the main combustion chamber was fueled with lean mixture by the means of a carburetor. During the tests we have used two types of main combustion chamber and three types of secondary combustion chamber. Thus, we had the possibility to use different compression ratios, starting with the lower ones, imposed by the less volatile fuels and ending with the higher ones, that led to the highest output power and a steady working process. In the meantime, three types of spark plugs were tested. We have also studied the HC and CO emissions, as well as the fuel consumption.

scholarly journals Combustion chamber geometry and fuel supply system variations on fuel economy and exhaust emissions of GDI engine with EGR

2021 ◽  
pp. 358-358
Author(s):  
Shivakumar Nagareddy ◽  
Kumaresan Govindasamy
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Gasoline Direct Injection ◽  
Injection Timing ◽  
Fuel Injector ◽  
Combustion Modes ◽  
Crown Shape ◽  
Fuel Injection Pressure

In this study, the combustion chamber geometry for spray-guided, wall-guided, and air-guided combustion strategies were fabricated. The piston crown shape and the cylinder head in each combustion chamber geometry was machined by fixing the fuel injector and spark plug at proper positions to obtain swirl, turbulence, and squish effects for better mixing of fuel with air and superior combustion of the mixture. Conducted tests on all the three modified gasoline direct injection engines with optimized exhaust gas recirculation and electronic control towards fuel injection timing, the fuel injection pressure, and the ignition timing for better the performance and emissions control. It is clear from the results that NOx emissions from all three combustion modes were reduced by 4.9% upto 50% of loads and it increase for higher loads due to increase of in-cylinder pressure. The fuel consumption and emissions showed better at 150 bar Fuel Injection Pressure for wall-guided combustion chamber geometry. Reduced HC emissions by 3.7% and 4.7%, reduced CO emissions by 2% and 3.3%, reduced Soot emissions by 6.12% and 10.6%. Reduces specific fuel consumption by about 10.3% and 13.3% in wall-guided combustion strategy compare with spray-guided and air-guided combustion modes respectively.

Sign in / Sign up

Export Citation Format

Share Document