scholarly journals Surface roughness optimization in machining of AZ31 magnesium alloy using ABC algorithm

2018 ◽  
Vol 144 ◽  
pp. 03006 ◽  
Author(s):  
Abhijith ◽  
Pai Srinivasa ◽  
D’Mello Grynal ◽  
Hebbar Gautama
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Manufacturing Sector ◽  
Cutting Speed ◽  
Orthopedic Implants ◽  
Pso Algorithm ◽  
Optimization Techniques ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Abc Algorithm

Magnesium alloys serve as excellent substitutes for materials traditionally used for engine block heads in automobiles and gear housings in aircraft industries. AZ31 is a magnesium alloy finds its applications in orthopedic implants and cardiovascular stents. Surface roughness is an important parameter in the present manufacturing sector. In this work optimization techniques namely firefly algorithm (FA), particle swarm optimization (PSO) and artificial bee colony algorithm (ABC) which are based on swarm intelligence techniques, have been implemented to optimize the machining parameters namely cutting speed, feed rate and depth of cut in order to achieve minimum surface roughness. The parameter Ra has been considered for evaluating the surface roughness. Comparing the performance of ABC algorithm with FA and PSO algorithm, which is a widely used optimization algorithm in machining studies, the results conclude that ABC produces better optimization when compared to FA and PSO for optimizing surface roughness of AZ 31.

scholarly journals Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 617 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Jarosław Korpysa
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Operational Parameters

Surface roughness is among the key indicators describing the quality of machined surfaces. Although it is an aggregate of several factors, the condition of the surface is largely determined by the type of tool and the operational parameters of machining. This study sought to examine the effect that particular machining parameters have on the quality of the surface. The investigated operation was the high-speed dry milling of a magnesium alloy with a polycrystalline diamond (PCD) cutting tool dedicated for light metal applications. Magnesium alloys have low density, and thus are commonly used in the aerospace or automotive industries. The state of the Mg surfaces was assessed using the 2D surface roughness parameters, measured on the lateral and the end face of the specimens, and the end-face 3D area roughness parameters. The description of the surfaces was complemented with the surface topography maps and the Abbott–Firestone curves of the specimens. Most 2D roughness parameters were to a limited extent affected by the changes in the cutting speed and the axial depth of cut, therefore, the results from the measurements were subjected to statistical analysis. From the data comparison, it emerged that PCD-tipped tools are resilient to changes in the cutting parameters and produce a high-quality surface finish.

Multiobjective Optimization of End Milling HCHCr Using AlCrN PVD Coated Cutters With MOGA and RSMO

2014 ◽  
Author(s):  
Shantisagar K. Biradar ◽  
Geeta S. Lathkar
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Multiobjective Optimization ◽  
End Milling ◽  
Dominant Role ◽  
Optimization Technique ◽  
Cutting Speed ◽  
Optimization Techniques ◽  
Depth Of Cut ◽  
Machining Parameters

Here the End milling is studied for optimization of responses such as surface roughness and tool wear while machining HCHCr. These two conflicting responses decide the quality of process; therefore the multiobjective optimization technique is used. The Response Surface Optimizer (RSMO) and Multiobjective Genetic Algorithm (MOGA) were used as the multiobjective optimization techniques. The PVD coating of 2.5 micron AlCrN was used on four flute HSS End milling cutter. Input machining parameters were cutting speed, feed rate, depth of cut and percentage concentration of the solid lubricant MoS2 mixed with SAE-20 base oil. The experimentation was carried out using two level full factorial design concept while ANOVA technique has been used to verify the adequacy of mathematical model. It was found that the cutting speed (V) is having most dominant role on surface roughness and tool wear. The sensitivity analysis was carried out for studying sensitivity of input parameters for the responses.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

scholarly journals Optimization of machining parameters in face milling using multi-objective Taguchi technique

2018 ◽  
Vol 12 (2) ◽  
pp. 104-108 ◽  
Author(s):  
Yusuf Fedai ◽  
Hediye Kirli Akin
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Taguchi Technique ◽  
Average Roughness ◽  
Multi Objective ◽  
Control Factors ◽  
Average Maximum

In this research, the effect of machining parameters on the various surface roughness characteristics (arithmetic average roughness (Ra), root mean square average roughness (Rq) and average maximum height of the profile (Rz)) in the milling of AISI 4140 steel were experimentally investigated. Depth of cut, feed rate, cutting speed and the number of insert were considered as control factors; Ra, Rz and Rq were considered as response factors. Experiments were designed considering Taguchi L9 orthogonal array. Multi signal-to-noise ratio was calculated for the response variables simultaneously. Analysis of variance was conducted to detect the significance of control factors on responses. Moreover, the percent contributions of the control factors on the surface roughness were obtained to be the number of insert (71.89 %), feed (19.74 %), cutting speed (5.08%) and depth of cut (3.29 %). Minimum surface roughness values for Ra, Rz and Rq were obtained at 325 m/min cutting speed, 0.08 mm/rev feed rate, 1 number of insert and 1 mm depth of cut by using multi-objective Taguchi technique.

Machining characteristics of Inconel 718 under several cutting conditions based on Taguchi method

2012 ◽  
Vol 227 (9) ◽  
pp. 1889-1897 ◽  
Author(s):  
R Thirumalai ◽  
JS Senthilkumaar ◽  
P Selvarani ◽  
S Ramesh
Keyword(s):  
Surface Roughness ◽  
Inconel 718 ◽  
Flank Wear ◽  
Optimization Technique ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Machining Parameters ◽  
Dry Machining ◽  
Noise Factors

Extensive researchers have conducted several experiments in the past for selecting the optimum parameters in machining nickel based alloy – Inconel 718. These experiments conducted so far are dealt with dry machining and flooded coolant machining of nickel alloy Inconel 718. In this research study, the usage of refrigerated coolant is also dealt with and it is compared with dry machining and flooded coolant machining. Cutting speed, feed and depth of cut are considered as the machining parameters. The effectiveness of the refrigerated coolant in machining the heat resistant super alloy material Inconel 718 with respect to these machining parameters are described in this article. The machinability studies parameters were generated with surface roughness and flank wear. The performance of uncoated carbide cutting tool was investigated at various cutting condition under dry, flooded coolant and refrigerated coolant machining. The relationship between the machining parameters and the performance measures were established and using analysis of variance significant machining parameters determined. This article made an attempt to Taguchi optimization technique to study the machinability performances of Inconel 718. Taguchi approach is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer experiments than a factorial design. Taguchi’s optimization analysis indicates that the factors level, its significance to influence the surface roughness and flank wear for the machining processes. Confirmation tests were conducted at an optimal condition to make a comparison between the experimental results foreseen from the mentioned correlations.

Taguchi Method Based Experiments of Titanium TC11 Flank Milling Parameters

2009 ◽  
Vol 407-408 ◽  
pp. 608-611 ◽  
Author(s):  
Chang Yi Liu ◽  
Cheng Long Chu ◽  
Wen Hui Zhou ◽  
Jun Jie Yi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Flank Milling ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Mill Machining

Taguchi design methodology is applied to experiments of flank mill machining parameters of titanium alloy TC11 (Ti6.5A13.5Mo2Zr0.35Si) in conventional and high speed regimes. This study includes three factors, cutting speed, feed rate and depth of cut, about two types of tools. Experimental runs are conducted using an orthogonal array of L9(33), with measurement of cutting force, cutting temperature and surface roughness. The analysis of result shows that the factors combination for good surface roughness, low cutting temperature and low resultant cutting force are high cutting speed, low feed rate and low depth of cut.

scholarly journals The Experimental Investigation of Surface Roughness After Dry Turning of Steel S235

2019 ◽  
Vol 26 (4) ◽  
pp. 179-184
Author(s):  
Justyna Molenda
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Scientific Work ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Workpiece Material ◽  
Important Indicator

AbstractNowadays lot of scientific work inspired by industry companies was done with the aim to avoid the use of cutting fluids in machining operations. The reasons were ecological and human health problems caused by the cutting fluid. The most logical solution, which can be taken to eliminate all of the problems associated with the use of cooling lubricant, is dry machining. In most cases, however, a machining operation without lubricant finds acceptance only when it is possible to guarantee that the part quality and machining times achieved in wet machining are equalled or surpassed. Surface finish has become an important indicator of quality and precision in manufacturing processes and it is considered as one of the most important parameter in industry. Today the quality of surface finish is a significant requirement for many workpieces. Thus, the choice of optimized cutting parameters is very important for controlling the required surface quality. In the present study, the influence of different machining parameters on surface roughness has been analysed. Experiments were conducted for turning, as it is the most frequently used machining process in machine industry. All these parameters have been studied in terms of depth of cut (ap), feed rate (f) and cutting speed (vc). As workpiece, material steel S235 has been selected. This work presents results of research done during turning realised on conventional lathe CDS 6250 BX-1000 with severe parameters. These demonstrate the necessity of further, more detailed research on turning process results.

scholarly journals Statistical analysis of energy consumption, tool wear and surface roughness in machining of Titanium alloy (Ti-6Al-4V) under dry, wet and cryogenic conditions

2019 ◽  
Vol 10 (2) ◽  
pp. 561-573 ◽  
Author(s):  
Muhammad Ali Khan ◽  
Syed Husain Imran Jaffery ◽  
Mushtaq Khan ◽  
Muhammad Younas ◽  
Shahid Ikramullah Butt ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Effective Means ◽  
Sustainable Manufacturing ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Specific Cutting Energy ◽  
Cutting Energy ◽  
Positive Effect

Abstract. Productivity and economy are key elements of any sustainable manufacturing system. While productivity is associated to quantity and quality, economy focuses on energy efficient processes achieving an overall high output to input ratio. Machining of hard-to-cut materials has always posed a challenge due to increased tool wear and energy loss. Cryogenics have emerged as an effective means to improve sustainability in the recent past. In the present research the use of cooling conditions has been investigated as an input variable to analyze its effect on tool wear, specific cutting energy and surface roughness in combination with other input machining parameters of feed rate, cutting speed and depth of cut. Experimental design was based on Taguchi design of experiment. Analysis of Variance (ANOVA) was carried out to ascertain the contribution ratio of each input. Results showed the positive effect of coolant usage, particularly cryogenic, on process responses. Tool wear was improved by 33 % whereas specific cutting energy and surface roughness were improved by 10 % and 9 % respectively by adapting the optimum machining conditions.

scholarly journals Optimization of CNC Turning Parameters in Machining EN19 using Face Centered Central Composite Design Based RSM

2020 ◽  
Vol 9 (2) ◽  
pp. 889-896
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Removal Rate ◽  
Cutting Speed ◽  
Vital Role ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Cnc Turning ◽  
Software Analysis ◽  
Central Composite

Manufacturing a defect free (quality) product is playing a vital role in today’s globally competitive, customer oriented era. Meeting the demand of the market by producing sufficient quantity is another challenge. Achieving greater production rates without compromising on quality, increases the complexity of the task. Adopting modern manufacturing methods like CNC turning are essential to meet the above requirements. EN19 is an important member in the family of alloy steels, which has a wide variety of applications in automobile and machine tool industries. Optimization of machining parameters is crucial in obtaining the required outputs such as quality and productivity. In this work, optimization of CNC turning parameters for machining EN19 alloy steel is performed. The number of experiments was designed using face centred central composite based response surface methodology with varied independent process parameters namely cutting speed, feed and depth of cut. After designing the experiments, the performance measures such as surface roughness of the test samples and Material Removal Rate (MRR) is calculated using the existing formulae. The influence of parameters on MRR and surface roughness are determined by analysis of variance (ANOVA) and for significance interactions of the process parameters are also considered. Using MINITAB 17 software analysis is performed. Further, regression analysis has been done and second order mathematical model is obtained. Using desirability approach, optimization is carried out.

Machinability Investigation of HSLA Steel in Hard Turning with Coated Ceramic Tool: Assessment, Modeling, Optimization and Economic Aspects

2019 ◽  
Vol 18 (04) ◽  
pp. 625-655 ◽  
Author(s):  
Asutosh Panda ◽  
Sudhansu Ranjan Das ◽  
Debabrata Dhupal
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
Hard Turning ◽  
Flank Wear ◽  
Desirability Function ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Ceramic Tool ◽  
Life Estimation

The present study addresses the machinability investigation in finish dry hard turning of high strength low alloy steel with coated ceramic tool by considering cutting speed, feed and depth of cut as machining parameters. The technological parameters like surface roughness, flank wear, chip morphology and economical feasibility have been considered to investigate the machinability performances. Twenty seven set of trials according to full factorial design of experiments are performed and analysis of variance, multiple regression method, Taguchi method, desirability function approach and finally Gilbert’s approach are subsequently applied for parametric influence study, mathematical modeling, multi-response optimization, tool life estimation and economic analysis. Results indicated that feed and cutting speed are the most significant controlled as well as dominant factors for hard turning operation if the minimization of the machined surface roughness and tool flank wear is considered. Abrasions, adhesion followed by plastic deformation have been observed to be the principal wear mechanism for tool life estimation and observed tool life for coated ceramic insert is 47[Formula: see text]min under optimum cutting conditions. The total machining cost per part is ensued to be lower ($0.29 only) as a consequence of higher tool life, reduction in downtime and enhancement in savings, which finds economical benefits in hard turning. The current work demonstrates the substitution of conventional, expensive and slow cylindrical grinding process, and proposes the most expensive CBN tool alternative using coated ceramic tools in hard turning process considering techno-economical and ecological aspects.

Sign in / Sign up

Export Citation Format

Share Document