scholarly journals Triboelectric nanogenerator as self-powered impact sensor

2018 ◽  
Vol 148 ◽  
pp. 14005 ◽  
Author(s):  
Cristobal Garcia ◽  
Irina Trendafilova ◽  
Roberto Guzman de Villoria ◽  
Jose Sánchez del Río
Keyword(s):  
Polyvinylidene Fluoride ◽  
Mechanical Energy ◽  
Copper Electrode ◽  
Triboelectric Nanogenerator ◽  
Electric Response ◽  
Active Sensors ◽  
Ball Impact ◽  
Self Powered ◽  
Triboelectric Nanogenerators ◽  
The Impact

In recent years, triboelectric nanogenerators (TENGs) are used to harvest mechanical energy from ambient environment. These devices convert ambient energies (e.g. vibrations, breathing-driven, impacts or human body motions) into electricity based on the triboelectric effect. Furthermore, some TENGs can be successfully employed as self-power active sensors because the electric response from the TENG is proportional to the magnitude of the mechanical motion. This study report on the design and development of a novel triboelectric nanogenerator, and its potential application as self-powered impact sensor. To prepare the TENG device, membranes of polyvinylidene fluoride (PVDF) and polyvinylpyrrolidone (PVP) nanofibers are sandwiched between copper electrode films and wrapped on PET films. The TENG works based on the triboelectric interaction between the membranes of nanofibers. After the preparation, the TENGs are subjected to several impacts by the drop-ball impact test. The purpose of the experiment is to analyse if the electric response of TENG is dependent on the energy of the impact. The results of the experiment are presented and discussed. The main contributions of this work are the preparation of a novel nanogenerator (TENG) based on the triboelectric interaction between polyvinylidene fluoride and polyvinylpyrrolidone sub-micron polymer fibers and the investigation of its potential use as a self-powered impact sensor.

scholarly journals Triboelectric nanogenerator based on Teflon/vitamin B1 powder for self-powered humidity sensing

2020 ◽  
Vol 11 ◽  
pp. 1394-1401
Author(s):  
Liangyi Zhang ◽  
Huan Li ◽  
Yiyuan Xie ◽  
Jing Guo ◽  
Zhiyuan Zhu
Keyword(s):  
Relative Humidity ◽  
Mechanical Energy ◽  
Vitamin B1 ◽  
Cost Effective ◽  
Electrical Energy ◽  
Open Circuit ◽  
Triboelectric Nanogenerator ◽  
Cost Effective Method ◽  
Self Powered ◽  
Triboelectric Nanogenerators

Recently, there has been growing interest in triboelectric nanogenerators (TENGs) that can effectively convert various forms of mechanical energy input into electrical energy. In the present study, a novel Teflon/vitamin B1 powder based triboelectric nanogenerator (TVB-TENG) is proposed. Paper is utilized as a supporting platform for triboelectrification between a commercial Teflon tape and vitamin B1 powder. The measured open-circuit voltage was approximately 340 V. The TVB-TENG can be applied as a humidity sensor and exhibits a linear and reversible response to the relative humidity of the environment. Moreover, the change in relative humidity is also indicated by the change in luminosity of a set of light-emitting diodes (LEDs) integrated in the TVB-TENG system. The TVB-TENG proposed in this study illustrates a cost-effective method for portable power supply and sensing devices.

scholarly journals The Progress of PVDF as a Functional Material for Triboelectric Nanogenerators and Self-Powered Sensors

Micromachines ◽  
2018 ◽  
Vol 9 (10) ◽  
pp. 532 ◽  
Author(s):  
Jin Lee ◽  
Jae Lee ◽  
Jeong Baik
Keyword(s):  
Output Power ◽  
Polyvinylidene Fluoride ◽  
Rapid Development ◽  
Device Fabrication ◽  
Innovative Technology ◽  
Triboelectric Nanogenerator ◽  
New Energy ◽  
Piezoelectric Effects ◽  
Self Powered ◽  
Triboelectric Nanogenerators

Ever since a new energy harvesting technology, known as a triboelectric nanogenerator (TENG), was reported in 2012, the rapid development of device fabrication techniques and mechanical system designs have considerably made the instantaneous output power increase up to several tens of mW/cm2. With this innovative technology, a lot of researchers experimentally demonstrated that various portable/wearable devices could be operated without any external power. This article provides a comprehensive review of polyvinylidene fluoride (PVDF)-based polymers as effective dielectrics in TENGs for further increase of the output power to speed up commercialization of the TENGs, as well as the fundamental issues regarding the materials. In the end, we will also review PVDF-based sensors based on the triboelectric and piezoelectric effects of the PVDF polymers.

scholarly journals Wearable Woven Triboelectric Nanogenerator Utilizing Electrospun PVDF Nanofibers for Mechanical Energy Harvesting

Micromachines ◽  
2019 ◽  
Vol 10 (7) ◽  
pp. 438 ◽  
Author(s):  
Muhammad Omar Shaikh ◽  
Yu-Bin Huang ◽  
Cheng-Chien Wang ◽  
Cheng-Hsin Chuang
Keyword(s):  
Polyvinylidene Fluoride ◽  
Mechanical Energy ◽  
Wearable Devices ◽  
Human Motion ◽  
Triboelectric Nanogenerator ◽  
Free Standing ◽  
Β Phase ◽  
Applied Forces ◽  
Self Powered ◽  
High Output Voltage

Several wearable devices have already been commercialized and are likely to open up a new life pattern for consumers. However, the limited energy capacity and lifetime have made batteries the bottleneck in wearable technology. Thus, there have been growing efforts in the area of self-powered wearables that harvest ambient mechanical energy directly from surroundings. Herein, we demonstrate a woven triboelectric nanogenerator (WTENG) utilizing electrospun Polyvinylidene fluoride (PVDF) nanofibers and commercial nylon cloth to effectively harvest mechanical energy from human motion. The PVDF nanofibers were fabricated using a highly scalable multi-nozzle far-field centrifugal electrospinning protocol. We have also doped the PVDF nanofibers with small amounts of multi-walled carbon nanotubes (MWCNT) to improve their triboelectric performance by facilitating the growth of crystalline β-phase with a high net dipole moment that results in enhanced surface charge density during contact electrification. The electrical output of the WTENG was characterized under a range of applied forces and frequencies. The WTENG can be triggered by various free-standing triboelectric layers and reaches a high output voltage and current of about 14 V and 0.7 µA, respectively, for the size dimensions 6 × 6 cm. To demonstrate the potential applications and feasibility for harvesting energy from human motion, we have integrated the WTENG into human clothing and as a floor mat (or potential energy generating shoe). The proposed triboelectric nanogenerator (TENG) shows promise for a range of power generation applications and self-powered wearable devices.

scholarly journals Triboelectric Energy Harvesting Response of Different Polymer-Based Materials

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4980
Author(s):  
Tiago Rodrigues-Marinho ◽  
Nelson Castro ◽  
Vitor Correia ◽  
Pedro Costa ◽  
Senentxu Lanceros-Méndez
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Polyvinylidene Fluoride ◽  
Light Emission ◽  
Mechanical Energy ◽  
Harvesting Systems ◽  
Self Powered ◽  
Triboelectric Nanogenerators ◽  
Vertical Contact ◽  
The Internet Of Things

Energy harvesting systems for low-power devices are increasingly being a requirement within the context of the Internet of Things and, in particular, for self-powered sensors in remote or inaccessible locations. Triboelectric nanogenerators are a suitable approach for harvesting environmental mechanical energy otherwise wasted in nature. This work reports on the evaluation of the output power of different polymer and polymer composites, by using the triboelectric contact-separation systems (10 N of force followed by 5 cm of separation per cycle). Different materials were used as positive (Mica, polyamide (PA66) and styrene/ethylene-butadiene/styrene (SEBS)) and negative (polyvinylidene fluoride (PVDF), polyurethane (PU), polypropylene (PP) and Kapton) charge materials. The obtained output power ranges from 0.2 to 5.9 mW, depending on the pair of materials, for an active area of 46.4 cm2. The highest response was obtained for Mica with PVDF composites with 30 wt.% of barium titanate (BT) and PA66 with PU pairs. A simple application has been developed based on vertical contact-separation mode, able to power up light emission diodes (LEDs) with around 30 cycles to charge a capacitor. Further, the capacitor can be charged in one triboelectric cycle if an area of 0.14 m2 is used.

Single-electrode triboelectric nanogenerators based on sponge-like porous PTFE thin films for mechanical energy harvesting and self-powered electronics

2017 ◽  
Vol 5 (24) ◽  
pp. 12252-12257 ◽  
Author(s):  
Meng Wang ◽  
Nan Zhang ◽  
Yingjie Tang ◽  
Heng Zhang ◽  
Chuan Ning ◽  
...  
Keyword(s):  
Thin Films ◽  
Energy Harvesting ◽  
Mechanical Energy ◽  
Triboelectric Nanogenerator ◽  
Self Powered ◽  
Triboelectric Nanogenerators

A single-electrode triboelectric nanogenerator (S-TENG) based on sponge-like porous polytetrafluoroethylene (PTFE) thin films was developed.

scholarly journals Recent Progress in Self-Powered Sensors Based on Triboelectric Nanogenerators

Sensors ◽  
2021 ◽  
Vol 21 (21) ◽  
pp. 7129
Author(s):  
Junpeng Wu ◽  
Yang Zheng ◽  
Xiaoyi Li
Keyword(s):  
Mechanical Energy ◽  
Rapid Development ◽  
Electrical Energy ◽  
Displacement Current ◽  
Triboelectric Nanogenerator ◽  
Energy Harvesters ◽  
The Future ◽  
Quantitative Analysis Method ◽  
Self Powered ◽  
Triboelectric Nanogenerators

The emergence of the Internet of Things (IoT) has subverted people’s lives, causing the rapid development of sensor technologies. However, traditional sensor energy sources, like batteries, suffer from the pollution problem and the limited lifetime for powering widely implemented electronics or sensors. Therefore, it is essential to obtain self-powered sensors integrated with renewable energy harvesters. The triboelectric nanogenerator (TENG), which can convert the surrounding mechanical energy into electrical energy based on the surface triboelectrification effect, was born of this background. This paper systematically introduces the working principle of the TENG-based self-powered sensor, including the triboelectrification effect, Maxwell’s displacement current, and quantitative analysis method. Meanwhile, this paper also reviews the recent application of TENG in different fields and summarizes the future development and current problems of TENG. We believe that there will be a rise of TENG-based self-powered sensors in the future.

scholarly journals A Self-Powered and Highly Accurate Vibration Sensor Based on Bouncing-Ball Triboelectric Nanogenerator for Intelligent Ship Machinery Monitoring

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 218
Author(s):  
Taili Du ◽  
Xusheng Zuo ◽  
Fangyang Dong ◽  
Shunqi Li ◽  
Anaeli Elibariki Mtui ◽  
...  
Keyword(s):  
Signal To Noise Ratio ◽  
Work Conditions ◽  
Copper Electrode ◽  
Vibration Sensor ◽  
High Signal ◽  
Triboelectric Nanogenerator ◽  
Vibration Exciter ◽  
Bouncing Ball ◽  
3D Printed ◽  
Self Powered

With the development of intelligent ship, types of advanced sensors are in great demand for monitoring the work conditions of ship machinery. In the present work, a self-powered and highly accurate vibration sensor based on bouncing-ball triboelectric nanogenerator (BB-TENG) is proposed and investigated. The BB-TENG sensor consists of two copper electrode layers and one 3D-printed frame filled with polytetrafluoroethylene (PTFE) balls. When the sensor is installed on a vibration exciter, the PTFE balls will continuously bounce between the two electrodes, generating a periodically fluctuating electrical signals whose frequency can be easily measured through fast Fourier transform. Experiments have demonstrated that the BB-TENG sensor has a high signal-to-noise ratio of 34.5 dB with mean error less than 0.05% at the vibration frequency of 10 Hz to 50 Hz which covers the most vibration range of the machinery on ship. In addition, the BB-TENG can power 30 LEDs and a temperature sensor by converting vibration energy into electricity. Therefore, the BB-TENG sensor can be utilized as a self-powered and highly accurate vibration sensor for condition monitoring of intelligent ship machinery.

scholarly journals Light-Weight, Self-Powered Sensor Based on Triboelectric Nanogenerator for Big Data Analytics in Sports

Electronics ◽  
2021 ◽  
Vol 10 (19) ◽  
pp. 2322
Author(s):  
Xiaofei Ma ◽  
Xuan Liu ◽  
Xinxing Li ◽  
Yunfei Ma
Keyword(s):  
Big Data ◽  
Real Time ◽  
Data Analytics ◽  
Mechanical Energy ◽  
Rapid Development ◽  
Big Data Analytics ◽  
Triboelectric Nanogenerator ◽  
Light Weight ◽  
Table Tennis ◽  
Self Powered

With the rapid development of the Internet of Things (IoTs), big data analytics has been widely used in the sport field. In this paper, a light-weight, self-powered sensor based on a triboelectric nanogenerator for big data analytics in sports has been demonstrated. The weight of each sensing unit is ~0.4 g. The friction material consists of polyaniline (PANI) and polytetrafluoroethylene (PTFE). Based on the triboelectric nanogenerator (TENG), the device can convert small amounts of mechanical energy into the electrical signal, which contains information about the hitting position and hitting velocity of table tennis balls. By collecting data from daily table tennis training in real time, the personalized training program can be adjusted. A practical application has been exhibited for collecting table tennis information in real time and, according to these data, coaches can develop personalized training for an amateur to enhance the ability of hand control, which can improve their table tennis skills. This work opens up a new direction in intelligent athletic facilities and big data analytics.

Preparation of Polyvinylidene Fluoride (PVDF) Triboelectric Nanogenerators with Different Polymer

2015 ◽  
Vol 814 ◽  
pp. 91-95
Author(s):  
Cheng Wang ◽  
Hao Yu ◽  
Tao Huang ◽  
Chao Tan
Keyword(s):  
Polymer Films ◽  
Polyvinylidene Fluoride ◽  
Low Cost ◽  
Mechanical Energy ◽  
Flexible Polymer ◽  
Surrounding Environment ◽  
Nanofiber Membranes ◽  
External Consistency ◽  
Low Wear ◽  
Triboelectric Nanogenerators

Triboelectric nanogenerators have recently been used to harvest mechanical energy from surrounding environment which is of great significance in the field of energy conversion. Electrospinning provides a simple, low cost and versatile method for the generation of 1D nanostrucutures. Nanofiber membranes have many advantages over the commonly used dense film for designing the riboelectric nanogenerators, such as the low wear resistance caused from the internal and excellent external consistency of the electrospinning membranes. In this paper, we produce a variety of polymer films by electro-spinning, and fabricate Polyvinylidene Fluoride (PVDF) triboelectric nanogenerators with different polymer films afterwards. We except to explore the TEG power generation effect, and influencing factors, and then determine the best combination of the results of TEG (PVDF-PHBV). Such a flexible polymer TEG generates output voltage of up to 112 V at a power of 0.045W.

Sign in / Sign up

Export Citation Format

Share Document