scholarly journals Calorific properties of the wood biomass from some softwood species

2021 ◽  
Vol 343 ◽  
pp. 09001
Author(s):  
Cosmin Spîrchez ◽  
Aurel Lunguleasa ◽  
Constantin Ştefan Ionescu ◽  
Anamaria Avram
Keyword(s):  
Focal Spot ◽  
Combustion Process ◽  
Ash Content ◽  
International Standards ◽  
Wood Biomass ◽  
Combustible Material ◽  
Softwood Species

The aim of the paper is to highlight the importance of the calorific properties of softwood biomass. The paper presents the caloric power and ash content, important caloric properties in the assessment of wood biomass. Biomass, in the form of wood, was and will remain an important combustible material. The value of ash content for spruce was 3.8% and 4.2% for fir. These values are within the international standards. Wood biomass, as a material can provide the energy need for the population at a reduced price. The combustion process are possible only in the presence of oxygen, which is usually introduced into the focal spot through the combustion air.

scholarly journals Carbon Shale Combustion in the Fluidized Bed Reactor

2014 ◽  
Vol 16 (2) ◽  
pp. 74-76 ◽  
Author(s):  
Małgorzata Olek ◽  
Stanisław Kandefer ◽  
Wiesław Kaniowski ◽  
Witold Żukowski ◽  
Jerzy Baron
Keyword(s):  
Fluidized Bed ◽  
Flue Gas ◽  
Combustion Process ◽  
Fluidized Bed Reactor ◽  
Ash Content ◽  
Conversion Degree ◽  
Hard Coal ◽  
Combustible Material ◽  
High Quality ◽  
Bubbling Fluidized Bed

Abstract The purpose of this article is to present the possibilities of coal shale combustion in furnaces with bubbling fluidized bed. Coal shale can be autothermally combusted in the fluidized bed, despite the low calorie value and high ash content of fuel. Established concentrations of CO (500 ppm) and VOC (30 mg/m3) have indicated a high conversion degree of combustible material during combustion process. Average concentrations of SO2 and NOx in the flue gas were higher than this received from the combustion of high quality hard coal, 600 ppm and 500 ppm, respectively. Optional reduction of SO2 and NOx emission may require the installation of flue gas desulphurization and de-NOx systems.

Analysis of the Combustion Process of Selected Wood Biomass

2018 ◽  
pp. 725-733 ◽  
Author(s):  
Szymon Głowacki ◽  
Weronika Tulej ◽  
Mariusz Sojak ◽  
Andrzej Bryś ◽  
Jakub Kaczmarczyk ◽  
...  
Keyword(s):  
Combustion Process ◽  
Wood Biomass

scholarly journals Analysis of the efficiency of a solid fuel boiler depending on the choice of combusted fuel

2020 ◽  
Vol 154 ◽  
pp. 02003
Author(s):  
Grzegorz Pełka ◽  
Wojciech Luboń ◽  
Przemysław Pachytel
Keyword(s):  
Energy Efficiency ◽  
Solid Fuel ◽  
Combustion Process ◽  
Calorific Value ◽  
Volatile Matter ◽  
Ash Content ◽  
Solid Fuels ◽  
The Real ◽  
Residential Sector

In the municipal and residential sector in Poland, as many as 50% of households are heated by solid fuel boilers. Most often these are, unfortunately, inefficient boilers, fired with low-quality coal. This study characterizes the market of boilers for solid fuels in Poland, and also presents the main apportionment of these devices, due to the different criteria that characterize them. The current legal changes in the scope of energy and emission requirements for solid fuel boilers are also discussed. The main purpose of this work is to analyze the real efficiency of the solid fuel over-fired boiler used, depending on the fuel burned in it. The process of burning selected fuels (seasoned wood, coal and pea coal) in the boiler was preceded by tests of these fuels to determine their energy parameters, such as moisture, ash content, the share of volatile matter and calorific value. In the next step, the energy efficiency obtained by the tested solid fuel boiler during the combustion of selected solid fuels was compared. The highest efficiency was achieved during the combustion of pea coal, and the lowest was achieved during the combustion of wood. In any case, the nominal efficiency value was achieved. Solutions that could improve the quality of the combustion process in this type of boiler were proposed.

Combustion process of torrefied wood biomass

2016 ◽  
Vol 127 (2) ◽  
pp. 1339-1349 ◽  
Author(s):  
Aneta Magdziarz ◽  
Małgorzata Wilk ◽  
Robert Straka
Keyword(s):  
Combustion Process ◽  
Wood Biomass

scholarly journals The Reaction to Fire Test for Fire Retardant and for Combustible Material

2016 ◽  
Vol 11 (2) ◽  
pp. 22-28
Author(s):  
Adelaida Fanfarová ◽  
Ladislav Mariš
Keyword(s):  
Fire Test ◽  
Experimental Testing ◽  
Combustion Process ◽  
Real Life ◽  
Fire Retardant ◽  
Specific Area ◽  
Combustible Material ◽  
Hemp Fiber ◽  
Research Article ◽  
Timber Construction

Abstract Currently the natural materials become popular building material for houses, buildings and recreational property. The risk of fires in residential timber construction or eco houses cannot be completely ruled out, therefore there is a need for proper and correct implementing preventive measures and application of all available solutions, which may reduce the risk of fire as far as possible, to slow down the combustion process, to protect the life of people, animals and also the building itself until arrival members of the Fire and Rescue Services. Fireproofing of combustible materials is a specific area of fire protection. For scientific research as well as for real-life practice, not only their structural and physical properties, but also fire-technical characteristics are really important. The present researchers mostly focus on fire-retardant treatment of wood that is why the authors of this contribution focused on a different combustible material. This research article presents the experimental testing and examination of the reaction to fire test of the selected thermal insulation of hemp fiber that was impregnated by the selected fire retardant in laboratory conditions.

scholarly journals Physicochemical Characteristics and Microbiological Quality of Honey Produced in Benin

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
François Ezin Azonwade ◽  
Armand Paraïso ◽  
Cokou P. Agbangnan Dossa ◽  
Victorien T. Dougnon ◽  
Christine N’tcha ◽  
...  
Keyword(s):  
Reducing Sugars ◽  
Microbiological Quality ◽  
Physicochemical Characteristics ◽  
Ash Content ◽  
International Standards ◽  
Free Acidity ◽  
Total Sugars ◽  
Microbiological Characteristics ◽  
Significant Difference

Honey is a very complex biological product. It has great diversity, giving it a multitude of properties, both nutritionally and therapeutically. This study aimed to study the physicochemical and microbiological characteristics of honeys collected during the dry and rainy seasons in the different phytogeographical areas of Benin. The study revealed that all honeys had pH, water content, electrical conductivity, ash content, free acidity, total sugars, and reducing sugars, respectively, ranging within 3.65–4.09; 12.07–13.16%; 530.25–698.50 μs/cm; 0.42–0.53%; 35.67–40.52 meq/kg; 60–70%; and 58–70%. Moisture content, total sugars, and reducing sugars varied very significantly (p<0.05top<0.001) from one area to another and from one season to another. However, only the production season has a significant influence (p<0.05) on the pH of the honey. With regard to the ash content, free acidity, and electrical conduction, no significant difference (p>0.05) between the zones or between the seasons was observed. The results of the microbiological characterization showed that there is heterogeneity in the microbial load. These results have shown that these honeys meet international standards and their characterization will make it possible to obtain Beninese quality labels.

scholarly journals Durability of Biomass Briquettes

2006 ◽  
Vol 1 ◽  
pp. 139
Author(s):  
A. Kaķītis ◽  
I. Nulle
Keyword(s):  
Particle Size ◽  
Shear Stress ◽  
Combustion Process ◽  
International Standards ◽  
National Standards ◽  
Ultimate Shear Strength ◽  
Material Particle ◽  
Ultimate Shear Stress ◽  
Cereal Straw

The main resources for biomass agro-ecotechnologies are cereal straw residues, energy crops and emergent vegetation from wetlands. The herbaceous biomass is a material of low density (20 – 60kg/m3) therefore new mobile equipment and technologies for biomass comminution and densification have to be worked out. To guarantee the quality of biomass briquettes in the handling and usage process, sufficient durability of briquettes should be provided. National Standards of biomass briquettes should be worked out in accordance with the requirements of International Standards. Dependence of Ultimate shear stress on wheat stalk material particle size in biomass briquettes was investigated. It was stated that ultimate shear stress increases for particle size in briquettes less than 0.5mm. Peat additive improves the density and ultimate shear strength of briquettes, but peat in combustion process increases the ash content. Therefore it is not necessary to add peat more than 50% in briquetting composition. Durability of reed stalk briquettes ~1.7 times exceeds durability of wheat stalk briquettes. Maximal values of ultimate shear stress (1,5 MPa) and density (1,2 g/cm3) for pure peat (100%) briquettes was obtained.

scholarly journals From the Beehives: Identification and Comparison of Physicochemical Properties of Algerian Honey

Resources ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 94
Author(s):  
Mokhtar Guerzou ◽  
Hani Amir Aouissi ◽  
Ahlem Guerzou ◽  
Juris Burlakovs ◽  
Salaheddine Doumandji ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Physicochemical Properties ◽  
Water Content ◽  
Physicochemical Parameters ◽  
Ash Content ◽  
International Standards ◽  
Free Acidity ◽  
Codex Alimentarius ◽  
Index Analysis ◽  
Geographical Locations

In this study, the authors aimed at characterizing 11 Algerian kinds of honey taken from various geographical locations (beehives located at Djelfa (Medjbara and Dzaira), Laghouat, Aflou, Medea, Tiaret, Sidi bel-Abbes, Tiaret, Ain-Safra, Mostaganem, El Bayadh, and Ghardïa). The authors investigated the physicochemical parameters of these honey samples, including density, water content, electrical conductivity, ash content, pH, hydroxymethylfurfural (HMF) content, free acidity, and color. The physicochemical parameters obtained were found to be within acceptable ranges according to the international standards (Codex Alimentarius) for 9 out of 11 analyzed samples: density 1.38–1.50 g/cm3 (the same as kg/L, as commonly used for honey), water content 14.03–18.80%, electrical conductivity 0.38 × 10−1 − 6.41 × 10−1 mS/cm, ash content 0.06–0.48%, pH 3.50–4.50, free acidity 11–47 meq/kg, and color 1.1–9.2 Pfund index. Analysis of HMF content showed that only two honey samples have high values (117.7 and 90.0 meq/kg). Most samples of Algerian honey are of suitable quality according to international standards.

scholarly journals Dual-fuel combustion in a tangential PC-fired boiler of type OP-230 – computational simulations

2018 ◽  
Vol 70 ◽  
pp. 03009
Author(s):  
Przemysław Motyl ◽  
Jan Łach
Keyword(s):  
Combustion Process ◽  
Biomass Gasification ◽  
Agricultural Residues ◽  
Dual Fuel ◽  
Wood Biomass ◽  
Computational Simulations ◽  
Cfd Simulations ◽  
Dual Fuel Combustion ◽  
Firing Technology ◽  
Air Staging

Syngas co-firing in coal fired boilers can be one of the prospective technologies which may help to retrofit some of still functioning older boilers. This study focuses on the results of CFD simulations of wood biomass-derived syngas co-firing with coal in an older mid-sized tangential PC-fired boiler of type OP-230. The design and the implementation of the combustion process predispose the boiler to the connection with the biomass gasifier in which low calorific syngas from solid raw biomass gasification can be produced and next used as a supplemental fuel in the coal furnace. The simulations were performed to predict the influence of the improvement of the air staging via the dual-fuel technique based on the indirect co-firing technology on both the reductions in NOx emissions relative to the baseline (no syngas) and the residence time of syngas particles in a zone with the temperature higher than 1123K. This way one can determine whether the boiler can be recommended to indirect co-firing of syngas derived from agricultural residues biomass or SRF gasification containing such troublesome components as chlorine and alkali.

scholarly journals Assessment of the Composition of Forest Waste in Terms of Its Further Use

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 973
Author(s):  
Marta Bożym ◽  
Arkadiusz Gendek ◽  
Grzegorz Siemiątkowski ◽  
Monika Aniszewska ◽  
Jan Malaťák
Keyword(s):  
Heavy Metals ◽  
Alkali Metals ◽  
Energy Use ◽  
Heavy Metal Contamination ◽  
Combustion Process ◽  
Calorific Value ◽  
Ash Content ◽  
Pollutant Emissions ◽  
Forest Residues ◽  
Logging Residues

This paper presents the results of the analysis of the chemical composition and content of heavy metal contamination in forest logging residues, in order to assess the possibility for their further utilisation. The samples were divided into 9 groups, which included coniferous tree cones, wood, and other multi-species logging residues. The elementary composition, ash content, and calorific value were determined as energy use indicators for the samples. Additionally, the content of heavy and alkali metals, which may affect combustion processes and pollutant emissions, was tested. The high content of heavy metals may also disqualify these residues for other uses. The research shows that the test residues are suitable for energy use due to their high calorific value and low content of heavy metals. However, an increased ash content in some samples and the presence of alkali metals, causing high-temperature corrosion of boilers, may disqualify them as a potential fuel in the combustion process. The forest residues may be used in other thermal processes such as pyrolysis or gasification. A low content of heavy metals and a high content of organic matter permit the use of these residues for the production of adsorbents or composite materials.

Sign in / Sign up

Export Citation Format

Share Document