Treatment of High-Strength Pharmaceutical Wastewater and Removal of Antibiotics in Anaerobic and Aerobic Biological Treatment Processes

2006 ◽  
Vol 132 (1) ◽  
pp. 129-136 ◽  
Author(s):  
Ping Zhou ◽  
Chengyi Su ◽  
Binwei Li ◽  
Yi Qian
2000 ◽  
Vol 42 (1-2) ◽  
pp. 111-116 ◽  
Author(s):  
O. Goorany ◽  
I. Oztürk

The most important factor that affects the quality of effluents and overall organic matter removal in biological treatment processes is the presence of soluble microbial products (SMP) that are produced during biological treatment and remain in effluent. High strength wastewater from fermentation industry (FIE) was used as a slowly degradable substrate to investigate SMP formation in aerobic and anaerobic treatment. For SMP determination which forms a major part of residual soluble COD of the wastewater, the initial inert soluble COD (SI) was determined. It was found that SI/So is 0.122 and 0.164 for aerobic and anaerobic processes, respectively. During aerobic treatment of FIE for initialCOD (So) values varying between 1540–6645 mg COD/L, SMP are expected to vary within the range of 12.5–8.6% of So, respectively. In anaerobic treatment of the FIE, for values of 2670–6585 mg COD/L, SMP are expected to vary within the range of 9.8–6.2% of So, respectively. Molecular weight distribution analyses of raw wastewater, aerobic and anaerobic treatment effluent indicate that in both systems the effluent of FIE presents similar molecular weight fractions and are very high compared to raw wastewater.


2013 ◽  
Vol 726-731 ◽  
pp. 2140-2145 ◽  
Author(s):  
Wan Qian Guo ◽  
Ren Li Yin ◽  
Xian Jiao Zhou

The release of antibiotic pharmaceutical wastewater has caused a serious environmental problem. In order to provide a better guideline for the antibiotic wastewater treatment, this paper summarizes a critical review on the current biological technologies available for antibiotic wastewater degradation, including aerobic processes, anaerobic processes, anaerobic-aerobic processes, and other combined processes. Furthermore, applications of the antibiotic wastewater biological treatment processes are discussed as well.


Author(s):  
N. Zaletova ◽  
S. Zaletov

Биологический метод очистки сточных вод представляет собой сложный многокомпонентный процесс, ключевой составляющей которого является работа ферментной системы. Известно, что одним из важнейших ферментов, обеспечивающих биологический процесс, являются дегидрогеназы. Полностью сложнейший механизм действия ферментов до конца пока не раскрыт, однако в практике контроля процессов биологической очистки используется показатель дегидрогеназной активности ила. Результаты исследований позволили дополнить имеющуюся информацию фактическими данными о взаимообусловленности уровня дегидрогеназной активности ила и показателей отдельных технологических параметров биологической очистки. Показано, что режим работы аэротенков (нагрузка на ил, доза активного ила и др.) и величина показателей исходной дегидрогеназной активности и дегидрогеназной активности этого же образца ила со слабо концентрированным раствором (ДАИН2О) связаны между собой и зависят от нагрузки на ил по органическим веществам. Полученные результаты исследования могут быть использованы для контроля биологического процесса очистки сточных вод.The biological method of wastewater treatment is a comprehensive multicomponent process the activities of the enzyme system being the key component of it. It is known that dehydrogenases have been one of the most important enzymes the ensure the biological process. The complicated mechanism of the action of enzymes has not been fully described so far however, in the practice of monitoring biological treatment processes, an indicator of the dehydrogenase activity of sludge is used. The research results provided for supplementing the available information with actual data on the interdependence of the level of dehydrogenase activity of sludge and indicators of individual process parameters of biological treatment. It was shown that the mode of operation of aeration tanks (organic matter load on sludge, dose of activated sludge, etc.) and the values of the initial dehydrogenase activity and dehydrogenase activity of the same sludge sample with weakly concentrated solution (DASН2О) are interconnected and depend on the organic load on sludge. The results of the study can be used to control the biological process of wastewater treatment.The biological method of wastewater treatment is a comprehensive multicomponent process the activities of the enzyme system being the key component of it. It is known that dehydrogenases have been one of the most important enzymes the ensure the biological process. The complicated mechanism of the action of enzymes has not been fully described so far however, in the practice of monitoring biological treatment processes, an indicator of the dehydrogenase activity of sludge is used. The research results provided for supplementing the available information with actual data on the interdependence of the level of dehydrogenase activity of sludge and indicators of individual process parameters of biological treatment. It was shown that the mode of operation of aeration tanks (organic matter load on sludge, dose of activated sludge, etc.) and the values of the initial dehydrogenase activity and dehydrogenase activity of the same sludge sample with weakly concentrated solution (DASН2О) are interconnected and depend on the organic load on sludge. The results of the study can be used to control the biological process of wastewater treatment.


2015 ◽  
Vol 5 (0) ◽  
pp. 9781780402345-9781780402345 ◽  
Author(s):  
F. Cervantes ◽  
S. Pavlostathis ◽  
A. van Haandel

1986 ◽  
Vol 18 (7-8) ◽  
pp. 289-296
Author(s):  
C. F. Ouyang ◽  
T. J. Wan

This study investigated and compared the treatment characteristics of three different kinds of biological wastewater treatment plants (including rotating biological contactor, trickling filter and oxidation ditch) which are currently operated in Taiwan. The field investigation of this study concentrated on the following items: the performance of biological oxygen demand (BOD) and suspended solids (SS) removal; the sludge yield rate of BOD removal; the settleability of sludge solids; the properties of sludge thickening; the power consumption and land area requirement per unit volume of wastewater. Finally, based on the results of the field investigation, a comparison of the treatment characteristics of the three different biological treatment processes was evaluated.


2021 ◽  
Vol 65 (4) ◽  
pp. 643-651
Author(s):  
Th. Nitschke-Pagel ◽  
J. Hensel

AbstractThe consideration of residual stresses in fatigue-loaded welds is currently done only qualitatively without reliable knowledge about their real distribution, amount and prefix. Therefore, the tools which enable a more or less unsafe consideration in design concepts are mainly based on unsafe experiences and doubtful assumptions. Since the use of explicitly determined residual stresses outside the welding community is state of the art, the target of the presented paper is to show a practicable way for an enhanced consideration of residual stresses in the current design tools. This is not only limited on residual stresses induced by welding, but also on post-weld treatment processes like HFMI or shot peening. Results of extended experiments with longitudinal fillet welds and butt welds of low and high strength steels evidently show that an improved use of residual stresses in fatigue strength approximation enables a better evaluation of peening processes as well as of material adjusted welding procedures or post-weld stress relief treatments. The concept shows that it is generally possible to overcome the existing extremely conservative but although unsafe rules and regulations and may also enable the improved use of high strength steels.


Sign in / Sign up

Export Citation Format

Share Document