Ion energy control in an insulating inductively coupled discharge reactor

1997 ◽  
Vol 70 (15) ◽  
pp. 1950-1952 ◽  
Author(s):  
Brian A. Smith ◽  
Lawrence J. Overzet
1998 ◽  
Vol 510 ◽  
Author(s):  
T. Maeda ◽  
J. W. Lee ◽  
C. R. Abernathy ◽  
S. J. Pearton ◽  
F. Ren ◽  
...  

AbstractThe effects of Inductively Coupled Plasma (ICP) and Electron Cyclotron Resonance (ECR) H2 plasmas on GaAs metal semiconductor field effect transistors (MESFETs), high electron mobility transistors (HEMTs) and heterojunction bipolar transistors (HBTs) have been measured as a function of ion flux, ion energy and process pressure. The chemical effects of hydrogenation have been compared to direct physical bombardment by Ar plasmas under the same conditions. Si dopant passivation in MESFETs and HEMTs and C base-dopant passivation in HBTs produces much larger changes in sheet resistance, breakdown voltage and device gain or transconductance than Ar ion bombardment and suggests that H2-containing plasma chemistries (CH4/H2 for semiconductor etching, SiH4 for dielectric deposition, CHF3 for dielectric etching) should be avoided, or at least the exposure of the surface minimized. In some cases the device degradation is less for higher source power conditions, due to the suppression of cathode dc self-bias and hence ion energy.


2018 ◽  
Vol 37 (6) ◽  
pp. 545-550
Author(s):  
Mikhail Isupov ◽  
Vadim Pinaev ◽  
Daria Mul ◽  
Natalia Belousova

AbstractAn experimental investigation of plasma-assisted nitriding of austenitic stainless steel AISI 321 in a low-pressure (7 Pa), low-frequency (50–100 kHz) nitrogen inductively coupled plasma enhanced with ferromagnetic cores has been performed at the temperatures of 470–625 °C, sample biases of ‒500–‒750 V, current densities on the sample surface of 1.2–3.3 mA/cm2 and nitriding times of 20 and 60 min. It is found that even the short (20 min) ion-plasma treatment results in the formation of nitrided layers with the thickness of up to 40 μm and microhardness of up to 9 GPa.The high speed of nitriding can be explained as a result of the joint action of high ion flux density and high ion energy on the sample surface.


2019 ◽  
Vol 28 (11) ◽  
pp. 114001 ◽  
Author(s):  
Stefan Ries ◽  
Lars Banko ◽  
Marcus Hans ◽  
Daniel Primetzhofer ◽  
Jochen M Schneider ◽  
...  

1998 ◽  
Vol 512 ◽  
Author(s):  
J. J. Wang ◽  
Hyun Cho ◽  
E. S. Lambers ◽  
S. J. Peartont ◽  
M. Ostling ◽  
...  

ABSTRACTA parametric study of the etching characteristics of 6H p+ and n+ SiC and thin film SiC0.8N0.2 in Inductively Coupled Plasma NF3/O2 and NF3/Ar discharges has been performed. The etch rates in both chemistries increase monotonically with NF3 percentage and rf chuck power reaching 3500Å·min−1 for SiC and 7500 Å·min−1 for SiCN. The etch rates go through a maximum with increasing ICP source power, which is explained by a trade-off between the increasing ion flux and the decreasing ion energy. The anisotropy of the etched features is also a function of ion flux, ion energy and atomic fluorine neutral concentration. Indium-tinoxide( ITO) masks display relatively good etch selectivity over SiC(maximum of 70:1) while photoresist etches more rapidly than SiC. The surface roughness of SiC is essentially independent of plasma composition for NF3/O2 discharges, while extensive surface degradation occurs for SiCN under high NF3:O2 conditions. The high ion flux available in the ICP tool allows etching even at very low dc self-biases, ≤ −10V, leading to very low damage pattern transfer.


2006 ◽  
Vol 15 (4) ◽  
pp. 714-726 ◽  
Author(s):  
Jie Zhou ◽  
Ina T Martin ◽  
Reed Ayers ◽  
Eli Adams ◽  
Dongping Liu ◽  
...  

2020 ◽  
Vol 27 (9) ◽  
pp. 093512
Author(s):  
Sha-Sha Song ◽  
Wei Liu ◽  
Shuai Yin ◽  
Yong-Xin Liu ◽  
Fei Gao ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document