Direct Measurement of Mechanical and Adhesive Properties of Living Cells Using Surface Forces Apparatus

2007 ◽  
Vol 60 (9) ◽  
pp. 638 ◽  
Author(s):  
Xavier Banquy ◽  
Jean-Michel Rabanel ◽  
Patrice Hildgen ◽  
Suzanne Giasson
Keyword(s):  
Single Cells ◽  
Living Cells ◽  
Surface Forces ◽  
Force Measurements ◽  
Surface Forces Apparatus ◽  
Adhesive Properties ◽  
Force Microscopy ◽  
Atomic Force ◽  
Cell Substrate ◽  
Mediate Cell

The adhesive and mechanical properties of living cells assembled into a monolayer on two different substrates were investigated using the surface forces apparatus (SFA) technique. The force measurements allowed elastic and bending moduli of the cells plated on substrates to be determined. The moduli are in good agreement with data reported in the literature for single cells determined using atomic force microscopy. Results confirm that the nature of the cell–substrate interactions can mediate cell mechanical and adhesive properties.

scholarly journals 3D phonon microscopy with sub-micron axial-resolution

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Richard J. Smith ◽  
Fernando Pérez-Cota ◽  
Leonel Marques ◽  
Matt Clark
Keyword(s):  
Signal To Noise Ratio ◽  
Single Cells ◽  
Optical Resolution ◽  
Acquisition Time ◽  
Label Free ◽  
Axial Resolution ◽  
Force Microscopy ◽  
Atomic Force ◽  
Accuracy And Precision ◽  
Good Agreement

AbstractBrillouin light scattering (BLS) is an emerging method for cell imaging and characterisation. It allows elasticity-related contrast, optical resolution and label-free operation. Phonon microscopy detects BLS from laser generated coherent phonon fields to offer an attractive route for imaging since, at GHz frequencies, the phonon wavelength is sub-optical. Using phonon fields to image single cells is challenging as the signal to noise ratio and acquisition time are often poor. However, recent advances in the instrumentation have enabled imaging of fixed and living cells. This work presents the first experimental characterisation of phonon-based axial resolution provided by the response to a sharp edge. The obtained axial resolution is up to 10 times higher than that of the optical system used to take the measurements. Validation of the results are obtained with various polymer objects, which are in good agreement with those obtained using atomic force microscopy. Edge localisation, and hence profilometry, of a phantom boundary is measured with accuracy and precision of approximately 60 nm and 100 nm respectively. Finally, 3D imaging of fixed cells in culture medium is demonstrated.

scholarly journals Cell penetration efficiency analysis of different atomic force microscopy nanoneedles into living cells

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Marcos Penedo ◽  
Tetsuya Shirokawa ◽  
Mohammad Shahidul Alam ◽  
Keisuke Miyazawa ◽  
Takehiko Ichikawa ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Cell Membrane ◽  
Cell Biology ◽  
Cell Damage ◽  
Efficiency Analysis ◽  
Living Cells ◽  
Biomolecular Recognition ◽  
Cell Penetration ◽  
Force Microscopy ◽  
Atomic Force

AbstractOver the last decade, nanoneedle-based systems have demonstrated to be extremely useful in cell biology. They can be used as nanotools for drug delivery, biosensing or biomolecular recognition inside cells; or they can be employed to select and sort in parallel a large number of living cells. When using these nanoprobes, the most important requirement is to minimize the cell damage, reducing the forces and indentation lengths needed to penetrate the cell membrane. This is normally achieved by reducing the diameter of the nanoneedles. However, several studies have shown that nanoneedles with a flat tip display lower penetration forces and indentation lengths. In this work, we have tested different nanoneedle shapes and diameters to reduce the force and the indentation length needed to penetrate the cell membrane, demonstrating that ultra-thin and sharp nanoprobes can further reduce them, consequently minimizing the cell damage.

scholarly journals Anisotropic Mechanical Properties of Living Cells Revealed by Integrated Spinning Disk Confocal and Atomic Force Microscopy

2018 ◽  
Vol 114 (3) ◽  
pp. 513a
Author(s):  
Yuri M. Efremov ◽  
Mirian Velay-Lizancos ◽  
Daniel M. Suter ◽  
Pablo D. Zavattieri ◽  
Arvind Raman
Keyword(s):  
Mechanical Properties ◽  
Atomic Force Microscopy ◽  
Living Cells ◽  
Force Microscopy ◽  
Atomic Force ◽  
Spinning Disk ◽  
Anisotropic Mechanical Properties

scholarly journals 3P-311 Viscoelastic Properties of Many Living Cells Investigated by Atomic Force Microscopy(The 46th Annual Meeting of the Biophysical Society of Japan)

2008 ◽  
Vol 48 (supplement) ◽  
pp. S175
Author(s):  
Shinichiro Hiratsuka ◽  
Yusuke Mizutani ◽  
Masahiro Tsuchiya ◽  
Koichi Kawahara ◽  
Hiroshi Tokumoto ◽  
...  
Keyword(s):  
Atomic Force Microscopy ◽  
Annual Meeting ◽  
Viscoelastic Properties ◽  
Living Cells ◽  
Force Microscopy ◽  
Atomic Force ◽  
Biophysical Society

Surface diagnostics for scale analysis

2004 ◽  
Vol 49 (2) ◽  
pp. 183-190 ◽  
Author(s):  
S. Dunn ◽  
S. Impey ◽  
C. Kimpton ◽  
S.A. Parsons ◽  
J. Doyle ◽  
...  
Keyword(s):  
Adhesion Force ◽  
Polymer Materials ◽  
Rapid Screening ◽  
Force Measurements ◽  
Energy Materials ◽  
Force Microscopy ◽  
Atomic Force ◽  
Surface Modified ◽  
Surface Diagnostics ◽  
Microscopy Techniques

Stainless steel, polymethylmethacrylate and polytetrafluoroethylene coupons were analysed for surface topographical and adhesion force characteristics using tapping mode atomic force microscopy and force-distance microscopy techniques. The two polymer materials were surface modified by polishing with silicon carbide papers of known grade. The struvite scaling rate was determined for each coupon and related to the data gained from the surface analysis. The scaling rate correlated well with adhesion force measurements indicating that lower energy materials scale at a lower rate. The techniques outlined in the paper provide a method for the rapid screening of materials in potential scaling applications.

Sign in / Sign up

Export Citation Format

Share Document