Novel Four-Electrode Electromagnetic Flowmeter for the Measurement of Flow Rate in Polymer-Injection Wells

2014 ◽  
Vol 203 (1) ◽  
pp. 37-46 ◽  
Author(s):  
Xingbin Liu ◽  
Yanjun Wang ◽  
Ronghua Xie ◽  
Yuhui Zhang ◽  
Chunhui Huang ◽  
...  
SPE Journal ◽  
2022 ◽  
pp. 1-18
Author(s):  
Marat Sagyndikov ◽  
Randall Seright ◽  
Sarkyt Kudaibergenov ◽  
Evgeni Ogay

Summary During a polymer flood, the field operator must be convinced that the large chemical investment is not compromised during polymer injection. Furthermore, injectivity associated with the viscous polymer solutions must not be reduced to where fluid throughput in the reservoir and oil production rates become uneconomic. Fractures with limited length and proper orientation have been theoretically argued to dramatically increase polymer injectivity and eliminate polymer mechanical degradation. This paper confirms these predictions through a combination of calculations, laboratory measurements, and field observations (including step-rate tests, pressure transient analysis, and analysis of fluid samples flowed back from injection wells and produced from offset production wells) associated with the Kalamkas oil field in Western Kazakhstan. A novel method was developed to collect samples of fluids that were back-produced from injection wells using the natural energy of a reservoir at the wellhead. This method included a special procedure and surface-equipment scheme to protect samples from oxidative degradation. Rheological measurements of back-produced polymer solutions revealed no polymer mechanical degradation for conditions at the Kalamkas oil field. An injection well pressure falloff test and a step-rate test confirmed that polymer injection occurred above the formation parting pressure. The open fracture area was high enough to ensure low flow velocity for the polymer solution (and consequently, the mechanical stability of the polymer). Compared to other laboratory and field procedures, this new method is quick, simple, cheap, and reliable. Tests also confirmed that contact with the formation rapidly depleted dissolved oxygen from the fluids—thereby promoting polymer chemical stability.


2021 ◽  
Author(s):  
Dennis Alexis ◽  
Gayani Pinnawala ◽  
Do Hoon Kim ◽  
Varadarajan Dwarakanath ◽  
Ruth Hahn ◽  
...  

Abstract The work described in this paper details the development of a single stimulation package that was successfully used for treating an offshore horizontal polymer injection well to improve near wellbore injectivity in the Captain field, offshore UK. The practice was to pump these concentrated surfactant streams using multiple pumps from a stimulation vessel which is diluted with the polymer injection stream in the platform to be injected downhole. The operational challenges were maintaining steady injection rates of the different liquid streams which was exacerbated by the viscous nature of the concentrated surfactants that would require pre-dilution using cosolvent or heating the concentrated solutions before pumping to make them flowable. We have developed a single, concentrated liquid blend of surfactant, polymer and cosolvent that was used in near-wellbore remediation. This approach significantly simplifies the chemical remediation process in the field while also ensuring consistent product quality and efficiency. The developed single package is multiphase, multicomponent in nature that can be readily pumped. This blend was formulated based on the previous stimulation experience where concentrated surfactant packages were confirmed to work. Commercial blending of the single package was carried out based on lab scale to yard scale blending and dilution studies. About 420 MT of the blend was manufactured, stored, and transported by rail, road and offshore stimulation vessel to the field location and successfully injected.


2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Andreas Pesch ◽  
Steffen Melzer ◽  
Stephan Schepeler ◽  
Tobias Kalkkuhl ◽  
Romuald Skoda

Abstract A comparative study on the highly unsteady flow field in single- and two-blade pumps is performed. Stationary pump characteristics, as well as pressure and flow rate fluctuations, are presented. Wall pressure fluctuations were measured in the suction and pressure pipe as well as at several locations within the volute casing by piezoresistive transducers. Flow rate fluctuations were evaluated by a recently presented measurement system based on an electromagnetic flowmeter (Melzer et al. 2020, “A System for Time-Fluctuating Flow Rate Measurements in a Single-Blade Pump Circuit,” Flow Meas. Instrum., 71, p. 101675). Measurements were accompanied by three-dimensional (3D) flow simulations with the open-source cfd software foam-extend. A thorough grid study and validation of the simulation were performed. By a complementary analysis of measurement and simulation results, distinctive differences between both pump types were observed, e.g., flow rate and pressure fluctuation magnitudes are significantly higher in the single-blade pump. In relation to the respective mean values, flow rate fluctuation magnitudes are one order lower than pressure fluctuation magnitudes for both pumps. For the two-blade pump, fluctuations attenuate toward overload irrespective of the particular pump circuit, while they rise for the single-blade pump. 3D simulation results yield detailed insight into the spatially and temporally resolved impeller–volute interaction and reveal that the single-blade impeller pushes a high-pressure flow region forward in a way as a positive displacement pump, resulting in an inherently fluctuating velocity and pressure distribution within the volute.


2014 ◽  
Vol 670-671 ◽  
pp. 1016-1022
Author(s):  
Bing Hua Li ◽  
Xiao Juan Cao ◽  
Li Cai Liu ◽  
Fan Dong Zheng ◽  
Ni Zhang

Groundwater heat pump (GWHP) systems in three different hydrogeological fields, Beijing were selected, and their effects on temperature of groundwater in recharged aquifer were researched for three years. Results showed that the degree of thermal breakthrough was controlled by the distance between pumping wells and injection wells, and the temperature of groundwater with high flow rate can recover to normal faster than those with low flow rate. When distance between pumping wells and injection wells were shorter than 30m, thermal breakthrough may happen and the variation range of groundwater temperature during one heating or cooling period was 8~12°C.However, thermal breakthrough can be negligible and the temperature of groundwater may be steady when the distance between those wells was longer than 50m. Furthermore, GWHP in two different hydrogeological fields were selected to observe their effects on groundwater quality for one year. One GWHP was situated on the northwest piedmont alluvial fan of Beijing and the other was located in the southeast plain area of Beijing. Groundwater was sampled from those fields and thirty-two inorganic components were analyzed. Heavy metals were not detected, and calcium, magnesium, chloride, sulfate, fluoride and other ten inorganic components were studied. Groundwater quality in the northwest of Beijing was relatively steady because that aquifer was in relative oxidation environment. However, groundwater quality in the southeast of Beijing was subject to change because that aquifer was in relative reduction environment. Nitration reaction happened in the plain area, and ammonia, nitrite converted into nitrite nitrogen and nitrate nitrogen, respectively. Simultaneously, pH, concentrations of iron and manganese decreased, and total hardness increased.


2012 ◽  
Vol 594-597 ◽  
pp. 2486-2489
Author(s):  
Bao Jun Liu ◽  
Hai Xia Shi ◽  
Yun Sheng Cai

Separate layer water flooding is adopted in most oilfields in China and the injection flow rate is controlled by the diameter of water nozzle of each layer. In order to ensure the effect of water injection, applicable water nozzles need to be adjusted to meet the requirements of injection flow rate. The adjustment is commonly realized according to experience, which leads to long adjustment time and low efficiency. To solve this problem, the coupling model of wellbore conduit flow, throttled flow and formation seepage was established based on theoretical analysis, which could provide theoretical basis for water nozzles adjustment. In the model, the Bernoulli Equation was adopted to analyze wellbore conduit flow; indoor experiments were done to research throttled flow; the research object of the seepage was finite radius well in homogeneous infinite formation.


2005 ◽  
Author(s):  
Yan Wang ◽  
Demin Wang ◽  
Zhi Sun ◽  
Song Zhao ◽  
Gang Wang ◽  
...  

Author(s):  
N. M. Shayakhmetov ◽  
◽  
D. Y. Aizhulov ◽  

The paper discusses and research the factors affecting the filtration rate to reduce stagnant zones in the domain and spreading outside the block under consideration. The main hydrodynamic factors in production by In-Situ Leaching are the distribution of permeability in the reservoir and well flow rates. The study of the factors was carried out on the basis of mathematical models using Darcy Law and Law of Conservation of Mass. Calculation was accomplished on a two-dimensional area with an isotropic and non-uniform permeability distribution to determine the effect of permeability on the leached area. The permeability coefficient was distributed respectively over three zones, in the southern part the permeability was low, in the central transition from low to high, respectively, in the northern part there was a highly permeable zone. Three wells were located in the domain, with the production well in the center of the domain. Injection wells are located symmetrically with respect to a horizontal line passing through the center of the area under consideration. The calculation was carried out for three modes of well flow rates with the ratio of the flow rates of the injection wells 0.5 / 0.5, 0.2 / 0.8, 0.8 / 0.2 relative to the flow rate of the production well. On the basis of comparative analyzes of the obtained results, it is concluded that: at the same flow rates, regardless of the permeability of the zones, the results obtained show that the leaching area in the low-permeability zone is larger in comparison with the high-permeability zone; with an increase in permeability, the shape of the leaching zone tends from round to drop-shaped; with an increase in the flow rate of wells in the radius of the leaching zone, it increases if the flow rate of solutions is much higher than the filtration rate.


2011 ◽  
Vol 361-363 ◽  
pp. 370-376
Author(s):  
Xiang Rong Nie ◽  
Shi Qing Cheng

Polymer solution is known as non-Newtonian Fluid. Hence, when a well is injected by polymer solution, the well test data analysis using Newtonian fluid flow model will be erroneous. However, the analysis results usually were inaccurate when generalized non-Newtonian fluid model which considering polymer solution as power law fluid and taking no account of physical and chemical behaviors. These results clearly suggest the need for a study to come up with a new model considering both physical and chemical behaviors when polymer solution flowing in the reservoirs. At first, this study modified two parameter models: viscosity model and permeability decreasing coefficient model, all of them considering diffusion, conduction and IPV (inaccessible pore volume). Then, those models were applied to set up the new well testing model of a well located in an infinite reservoir. The log-log plots of the pressure and pressure derivatives have been prepared through numerical solutions. A further study has been done about the characteristics of the new type curves considering different parameters.


Sign in / Sign up

Export Citation Format

Share Document