scholarly journals Mechanical Properties of 3D Printed Polylactic Acid Product for Various Infill Design Parameters: A Review

2020 ◽  
Vol 1569 ◽  
pp. 042010 ◽  
Author(s):  
T J Suteja ◽  
A Soesanti
Keyword(s):  
Mechanical Properties ◽  
Polylactic Acid ◽  
Design Parameters ◽  
Acid Product ◽  
3D Printed

Effect of heat treatment on mechanical properties of 3D printed polylactic acid parts

2021 ◽  
Vol 63 (1) ◽  
pp. 73-78
Author(s):  
Pulkin Gupta ◽  
Sudha Kumari ◽  
Abhishek Gupta ◽  
Ankit Kumar Sinha ◽  
Prashant Jindal
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Polylactic Acid ◽  
Recrystallization Temperature ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Dog Bone ◽  
Heat Treated ◽  
Maximum Decrease ◽  
3D Printed

Abstract Fused deposition modelling (FDM) is a layer-by-layer manufacturing process type of 3D-printing (3DP). Significant variation in the mechanical properties of 3D printed specimens is observed because of varied process parameters and interfacial bonding between consecutive layers. This study investigates the influence of heat treatment on the mechanical strength of FDM 3D printed Polylactic acid (PLA) parts with constant 3DP parameters and ambient conditions. To meet the objectives, 7 sets, each containing 5 dog-bone shaped samples, were fabricated from commercially available PLA filament. Each set was subjected to heat treatment at a particular temperature for 1 h and cooled in the furnace itself, while one set was left un-treated. The temperature for heat treatment (Th) varied from 30 °C to 130 °C with increments of 10 °C. The heat-treated samples were characterized under tensile loading of 400 N and mechanical properties like Young’s modulus (E), Strain % ( ε ) and Stiffness (k) were evaluated. On comparing the mechanical properties of heat-treated samples to un-treated samples, significant improvements were observed. Heat treatment also altered the geometries of the samples. Mechanical properties improved by 4.88 % to 10.26 % with the maximum being at Th of 110 °C and below recrystallization temperature (Tr) of 65 °C. Deformations also decreased significantly at higher temperatures above 100 °C, by a maximum of 36.06 %. The dimensions of samples showed a maximum decrease of 1.08 % in Tr range and a maximum decrease of 0.31 % in weight at the same temperature. This study aims to benefit the society by establishing suitable Th to recover the lost strength in PLA based FDM 3D printed parts.

Mechanical Properties of 3D-Printed Wood-Plastic Composites

2018 ◽  
Vol 777 ◽  
pp. 499-507 ◽  
Author(s):  
Ossi Martikka ◽  
Timo Kärki ◽  
Qing Ling Wu
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
3D Printing ◽  
Impact Strength ◽  
Polylactic Acid ◽  
Wood Plastic Composite ◽  
Wood Plastic Composites ◽  
Plastic Composite ◽  
Plastic Composites ◽  
3D Printed

3D printing has rapidly become popular in both industry and private use. Especially fused deposition modeling has increased its popularity due to its relatively low cost. The purpose of this study is to increase knowledge in the mechanical properties of parts made of wood-plastic composite materials by using 3D printing. The tensile properties and impact strength of two 3D-printed commercial wood-plastic composite materials are studied and compared to those made of pure polylactic acid. Relative to weight –mechanical properties and the effect of the amount of fill on the properties are also determined. The results indicate that parts made of wood-plastic composites have notably lower tensile strength and impact strength that those made of pure polylactic acid. The mechanical properties can be considered sufficient for low-stress applications, such as visualization of prototypes and models or decorative items.

Temperature-compensated constitutive model of fused filament fabrication 3D printed PLA materials with full extrusion temperatures

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Kaiyang Zhu ◽  
Zichen Deng ◽  
Shi Dai ◽  
Yajun Yu
Keyword(s):  
Mechanical Properties ◽  
Thermal Decomposition ◽  
Constitutive Model ◽  
Polylactic Acid ◽  
Extrusion Temperature ◽  
Fused Filament Fabrication ◽  
Printing Process ◽  
Content Type ◽  
3D Printed ◽  
Interlayer Bonding

Purpose This study aims to focus on the effect of interlayer bonding and thermal decomposition on the mechanical properties of fused filament fabrication-printed polylactic acid specimens at high extrusion temperatures. Design/methodology/approach A printing process, that is simultaneous manufacturing of contour and specimen, is used to improve the printing accuracy at high extrusion temperatures. The effects of the extrusion temperature on the mechanical properties of the interlayer and intra-layer are evaluated via tensile experiments. In addition, the microstructure evolution affected by the extrusion temperature is observed using scanning electron microscopy. Findings The results show that the extrusion temperature can effectively improve the interlayer bonding property; however, the mechanical properties of the specimen for extrusion temperatures higher than 270°C may worsen owing to the thermal decomposition of the polylactic acid (PLA) material. The optimum extrusion temperature of PLA material in the three-dimensional (3D) printing process is recommended to be 250–270°C. Originality/value A temperature-compensated constitutive model for 3D printed PLA material under different extrusion temperatures is proposed. The present work facilitates the prediction of the mechanical properties of specimens at an extrusion temperature for different printing temperatures and different layers.

scholarly journals Effect of Porosity and Crystallinity on 3D Printed PLA Properties

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1487 ◽  
Author(s):  
Yuhan Liao ◽  
Chang Liu ◽  
Bartolomeo Coppola ◽  
Giuseppina Barra ◽  
Luciano Di Maio ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Complex Geometry ◽  
Fused Filament Fabrication ◽  
3D Printed ◽  
Physical Changes ◽  
Crystalline Forms

Additive manufacturing (AM) is a promising technology for the rapid tooling and fabrication of complex geometry components. Among all AM techniques, fused filament fabrication (FFF) is the most widely used technique for polymers. However, the consistency and properties control of the FFF product remains a challenging issue. This study aims to investigate physical changes during the 3D printing of polylactic acid (PLA). The correlations between the porosity, crystallinity and mechanical properties of the printed parts were studied. Moreover, the effects of the build-platform temperature were investigated. The experimental results confirmed the anisotropy of printed objects due to the occurrence of orientation phenomena during the filament deposition and the formation both of ordered and disordered crystalline forms (α and δ, respectively). A heat treatment post-3D printing was proposed as an effective method to improve mechanical properties by optimizing the crystallinity (transforming the δ form into the α one) and overcoming the anisotropy of the 3D printed object.

3D printed remendable polylactic acid blends with uniform mechanical strength enabled by a dynamic Diels–Alder reaction

2017 ◽  
Vol 8 (13) ◽  
pp. 2087-2092 ◽  
Author(s):  
Gayan A. Appuhamillage ◽  
John C. Reagan ◽  
Sina Khorsandi ◽  
Joshua R. Davidson ◽  
Walter Voit ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Polymer Blends ◽  
Polylactic Acid ◽  
Alder Reaction ◽  
Diels Alder ◽  
Diels Alder Reaction ◽  
3D Printed

We demonstrate that uniform mechanical properties can be achieved in 3D printed polymer blends by using a dynamic Diels–Alder reaction.

Investigation of future 3D printed brace design parameters: evaluation of mechanical properties and prototype outcomes

2019 ◽  
Vol 3 (4) ◽  
pp. 171-184
Author(s):  
Kenwick JL Ng ◽  
Kajsa Duke ◽  
Edmond Lou
Keyword(s):  
Mechanical Properties ◽  
Mechanical Characteristics ◽  
Treatment Effectiveness ◽  
Design Parameters ◽  
Wear Comfort ◽  
Polypropylene Material ◽  
Spinal Brace ◽  
3D Printed ◽  
Opening And Closing

Aim: Spinal brace wear time affects treatment effectiveness of adolescent idiopathic scoliosis but remains challenging with the brace’s bulkiness. This study aims to determine the appropriate material and thickness to improve wear comfort. Materials & methods: Thirty-one specimens were tested with 13 ULTEM1010 and 13 Nylon12 potential materials and 5 standard polypropylene material in 2.5, 3.25 and 4 mm thicknesses to evaluate mechanical properties. Donning tests of ULTEM1010 and Nylon12 printed braces were conducted. Results: Nylon12 with 2.5–3.25 mm thickness had higher flexibility and the closest mechanical characteristics as 4-mm thick polypropylene. ULTEM1010 brace fractured after 615-times and Nylon12 brace handled 2920-times of opening and closing. Conclusion: Nylon12, 2.5–3.25 mm are appropriate design parameters. Further clinical study can validate long term brace effectiveness.

scholarly journals 3D printing of composites: design parameters and flexural performance

2020 ◽  
Vol 26 (4) ◽  
pp. 699-706
Author(s):  
Feras Korkees ◽  
James Allenby ◽  
Peter Dorrington
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Volume Fraction ◽  
Fibre Volume Fraction ◽  
Fibre Volume ◽  
Design Parameters ◽  
Content Type ◽  
Flexural Performance ◽  
3D Printed ◽  
Strength And Stiffness

Purpose 3D printing of composites has a high degree of design freedom, which allows for the manufacture of complex shapes that cannot be achieved with conventional manufacturing processes. This paper aims to assess the design variables that might affect the mechanical properties of 3D-printed fibre-reinforced composites. Design/methodology/approach Markforged Mark-Two printers were used to manufacture samples using nylon 6 and carbon fibres. The effect of fibre volume fraction, fibre layer location and fibre orientation has been studied using three-point flexural testing. Findings The flexural strength and stiffness of the 3D-printed composites increased with increasing the fibre volume fraction. The flexural properties were altered by the position of the fibre layers. The highest strength and stiffness were observed with the reinforcement evenly distributed about the neutral axis of the sample. Moreover, unidirectional fibres provided the best flexural performance compared to the other orientations. 3D printed composites also showed various failure modes under bending loads. Originality/value Despite multiple studies available on 3D-printed composites, there does not seem to be a clear understanding and consensus on how the location of the fibre layers can affect the mechanical properties and printing versatility. Therefore, this study covered this design parameter and evaluated different locations in terms of mechanical properties and printing characteristics. This is to draw final conclusions on how 3D printing may be used to manufacture cost-effective, high-quality parts with excellent mechanical performance.

Sign in / Sign up

Export Citation Format

Share Document