scholarly journals Unsteady cavities near the hydrofoil with a small aspect ratio

2021 ◽  
Vol 2057 (1) ◽  
pp. 012033
Author(s):  
S G Skripkin ◽  
M A Tsoy ◽  
A Y Kravtsova
Keyword(s):  
Aspect Ratio ◽  
High Speed ◽  
Leading Edge ◽  
Digital Processing ◽  
Dimensionless Frequency ◽  
Cavitation Flow ◽  
Small Aspect Ratio ◽  
Cloud Cavitation ◽  
Low Aspect Ratio ◽  
Internal Instability

Abstract Using digital processing of high-speed visualization data on a cavitation flow near NACA hydrofoil with critically low aspect ratio, the frequencies of the formation and separation of cavities in the flow are identified. It is shown that in the case of development of cloud cavitation the main dimensionless frequency varies within 0.4, which corresponds to the type of internal instability. The Strouhal number corresponds to the frequency of attached cavity occurrence and varies in range from 0.6 to 0.8. The Strouhal numbers calculated in third mode exceed 1. This mode corresponds to the forming of very small cavities near the leading edge of hydrofoil.

scholarly journals Secondary Flow Control in Low Aspect Ratio Vanes Using Splitters

2016 ◽  
Author(s):  
Christopher Clark ◽  
Graham Pullan ◽  
Eric Curtis ◽  
Frederic Goenaga
Keyword(s):  
Kinetic Energy ◽  
Aspect Ratio ◽  
Secondary Flow ◽  
Current Practice ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Secondary Flows ◽  
Optimization Approach ◽  
Flow Strength ◽  
Low Aspect Ratio

Low aspect ratio vanes, often the result of overall engine architecture constraints, create strong secondary flows and high endwall loss. In this paper, a splitter concept is demonstrated that reduces secondary flow strength and improves stage performance. An analytic conceptual study, corroborated by inviscid computations, shows that the total secondary kinetic energy of the secondary flow vortices is reduced when the number of passages is increased and, for a given number of vanes, when the inlet endwall boundary layer is evenly distributed between the passages. Viscous computations show that, for this to be achieved in a splitter configuration, the pressure-side leg of the low aspect ratio vane horseshoe vortex, must enter the adjacent passage (and not “jump” in front of the splitter leading edge). For a target turbine application, four vane designs were produced using a multi-objective optimization approach. These designs represent: current practice for a low aspect ratio vane; a design exempt from thickness constraints; and two designs incorporating splitter vanes. Each geometry is tested experimentally, as a sector, within a low-speed turbine stage. The vane designs with splitters geometries were found to reduce the measured secondary kinetic energy, by up to 85%, to a value similar to the design exempt from thickness constraints. The resulting flowfield was also more uniform in both the circumferential and radial directions. One splitter design was selected for a full annulus test where a mixed-out loss reduction, compared to the current practice design, of 15.3% was measured and the stage efficiency increased by 0.88%.

Leading Edge and Wing Tip Flow Control on Low Aspect Ratio Wings

2010 ◽  
Author(s):  
Stefan Vey ◽  
David Greenblatt ◽  
Christian Nayeri ◽  
Christian Paschereit
Keyword(s):  
Aspect Ratio ◽  
Flow Control ◽  
Leading Edge ◽  
Low Aspect Ratio ◽  
Wing Tip ◽  
Low Aspect Ratio Wings

scholarly journals On the lift-optimal aspect ratio of a revolving wing at low Reynolds number

2018 ◽  
Vol 15 (143) ◽  
pp. 20170933 ◽  
Author(s):  
T. Jardin ◽  
T. Colonius
Keyword(s):  
Aspect Ratio ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Rossby Number ◽  
Subsequent Work ◽  
High Lift ◽  
Low Aspect Ratio ◽  
Axis Of Rotation ◽  
Edge Vortex ◽  
Convergent Solution

Lentink & Dickinson (2009 J. Exp. Biol. 212 , 2705–2719. ( doi:10.1242/jeb.022269 )) showed that rotational acceleration stabilized the leading-edge vortex on revolving, low aspect ratio (AR) wings and hypothesized that a Rossby number of around 3, which is achieved during each half-stroke for a variety of hovering insects, seeds and birds, represents a convergent high-lift solution across a range of scales in nature. Subsequent work has verified that, in particular, the Coriolis acceleration plays a key role in LEV stabilization. Implicit in these results is that there exists an optimal AR for wings revolving about their root, because it is otherwise unclear why, apart from possible morphological reasons, the convergent solution would not occur for an even lower Rossby number. We perform direct numerical simulations of the flow past revolving wings where we vary the AR and Rossby numbers independently by displacing the wing root from the axis of rotation. We show that the optimal lift coefficient represents a compromise between competing trends with competing time scales where the coefficient of lift increases monotonically with AR, holding Rossby number constant, but decreases monotonically with Rossby number, when holding AR constant. For wings revolving about their root, this favours wings of AR between 3 and 4.

The Effect of an Upstream Turbine on a Low-Aspect Ratio Vane

2004 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
N. W. Harvey
Keyword(s):  
High Pressure ◽  
Aspect Ratio ◽  
Leading Edge ◽  
Streamwise Vortex ◽  
Relative Magnitude ◽  
Large Radius ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Interaction Mechanisms ◽  
Low Aspect Ratio

The interaction between a high-pressure rotor and a downstream vane is dominated by vortex-blade interaction. Each rotor blade passing period two co-rotating vortex pairs, the tip-leakage and upper passage vortex and the lower passage and trailing shed vortex, impinge on, and are cut by, the vane leading edge. In addition to the streamwise vortex the tipleakage flow also contains a large velocity deficit. This causes the interaction of the tip-leakage flow with a downstream vane to differ from typical vortex blade interaction. This paper investigates the effect these interaction mechanisms have on a downstream vane. The test geometry considered was a low aspect ratio second stage vane located within a S-shaped diffuser with large radius change mounted downstream of a shroudless high-pressure turbine stage. Experimental measurements were conducted at engine-representative Mach and Reynolds numbers, and data was acquired using a fastresponse aerodynamic probe upstream and downstream of the vane. Time-resolved numerical simulations were undertaken with and without a rotor tip gap in order to investigate the relative magnitude of the interaction mechanisms. The presence of the upstream stage is shown to significantly change the structure of the secondary flow in the vane and to cause a small drop in its performance.

scholarly journals A vortex model for forces and moments on low-aspect-ratio wings in side-slip with experimental validation

2017 ◽  
Vol 473 (2198) ◽  
pp. 20160760 ◽  
Author(s):  
Adam C. DeVoria ◽  
Kamran Mohseni
Keyword(s):  
Aspect Ratio ◽  
Leading Edge ◽  
Streamwise Vorticity ◽  
Slender Body Theory ◽  
Vortex Model ◽  
Low Aspect Ratio ◽  
High Incidence ◽  
Stall Angle ◽  
Lift And Drag ◽  
Body Theory

This paper studies low-aspect-ratio ( ) rectangular wings at high incidence and in side-slip. The main objective is to incorporate the effects of high angle of attack and side-slip into a simplified vortex model for the forces and moments. Experiments are also performed and are used to validate assumptions made in the model. The model asymptotes to the potential flow result of classical aerodynamics for an infinite aspect ratio. The → 0 limit of a rectangular wing is considered with slender body theory, where the side-edge vortices merge into a vortex doublet. Hence, the velocity fields transition from being dominated by a spanwise vorticity monopole ( ≫ 1) to a streamwise vorticity dipole ( ∼ 1). We theoretically derive a spanwise loading distribution that is parabolic instead of elliptic, and this physically represents the additional circulation around the wing that is associated with reattached flow. This is a fundamental feature of wings with a broad-facing leading edge. The experimental measurements of the spanwise circulation closely approximate a parabolic distribution. The vortex model yields very agreeable comparison with direct measurement of the lift and drag, and the roll moment prediction is acceptable for ≤ 1 prior to the roll stall angle and up to side-slip angles of 20°.

Investigation of Unsteady Sheet Cavitation and Cloud Cavitation Mechanisms

1999 ◽  
Vol 121 (2) ◽  
pp. 289-296 ◽  
Author(s):  
T. M. Pham ◽  
F. Larrarte ◽  
D. H. Fruman
Keyword(s):  
High Speed ◽  
Leading Edge ◽  
Pressure Measurements ◽  
Foil Surface ◽  
Mean Velocity ◽  
Cloud Cavitation ◽  
Fluctuating Pressure ◽  
Sheet Cavitation ◽  
Cavitation Instability ◽  
Unsteady Characteristics

Sheet cavitation on a foil section and, in particular, its unsteady characteristics leading to cloud cavitation, were experimentally investigated using high-speed visualizations and fluctuating pressure measurements. Two sources of sheet cavitation instability were evidenced, the re-entrant jet and small interfacial waves. The dynamics of the re-entrant jet was studied using surface electrical probes. Its mean velocity at different distances from the leading edge was determined and its role in promoting the unsteadiness of the sheet cavitation and generating large cloud shedding was demonstrated. The effect of gravity on the dynamics of the re-entrant jet and the development of interfacial perturbations were examined and interpreted. Finally, control of cloud cavitation using various means, such as positioning a tiny obstacle (barrier) on the foil surface or performing air injection through a slit situated in the vicinity of the leading edge, was investigated. It was shown that these were very effective methods for decreasing the amplitude of the instabilities and even eliminating them.

scholarly journals Low Aspect Ratio Transonic Rotors: Part 2 — Influence of Location of Maximum Thickness on Transonic Compressor Performance

1992 ◽  
Author(s):  
A. R. Wadia ◽  
C. H. Law
Keyword(s):  
Aspect Ratio ◽  
Test Data ◽  
Three Dimensional ◽  
Leading Edge ◽  
Chord Length ◽  
Design Parameters ◽  
Transonic Compressor ◽  
Low Aspect Ratio ◽  
Maximum Thickness ◽  
Design Speed

Transonic compressor rotor performance is sensitive to variations in several known design parameters. One such parameter is the chordwise location of maximum thickness. This article reports on the design and experimental evaluation of two versions of a low aspect ratio transonic rotor that had the location of the tip blade section maximum thickness moved forward in two increments from the nominal 70 percent to 55 and 40 percent chord length, respectively. The original hub characteristics were preserved and the maximum thickness location was adjusted proportionately along the span. Although designed to satisfy identical design speed requirements, the experimental results reveal significant variation in the performance of the rotors. At design speed, the rotor with its maximum thickness located at 55 percent chord length attains the highest peak efficiency amongst the three rotors but has lowest flow rollback relative to the other two versions. To focus on current ruggedization issues for transonic blading (e.g. bird, ice ingestion), detailed comparison of test data and analysis to characterize the aerodynamic flow details responsible for the measured performance differences was confined to the two rotors with the most forward location of maximum thickness. A three-dimensional viscous flow analysis was used to identify the performance enhancing features of the higher efficiency rotor and to provide guidance in the interpretation of the experimental measurements. The computational results of the viscous analysis shows that the difference in performance between the two rotors can be attributed to the higher shock losses that result from the increased leading edge “wedge angle” as the maximum thickness is moved closer to the leading edge. The test data and the three-dimensional viscous analysis also reveal that the higher efficiency rotor achieves the same static pressure rise potential and loading at a higher flow level than its lesser efficient counterpart and this is responsible for its resulting lower flow rollback and apparent loss in stall margin. Comparison of the peak efficiencies attained by the two rotors described in this article with the baseline ruggedized rotor performance presented in part 1 of this paper suggests the existence of an optimum maximum thickness location at 55 to 60 percent chord length for such low aspect ratio transonic rotors.

scholarly journals High Speed Microactuators for Low Aspect Ratio High Speed Micro Aircraft Surfaces

Actuators ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 265
Author(s):  
Ronald Barrett-Gonzalez ◽  
Nathan Wolf
Keyword(s):  
Aspect Ratio ◽  
Flight Control ◽  
High Speed ◽  
High Performance ◽  
Dynamic Range ◽  
Feedback System ◽  
Analytical Models ◽  
Control Surface ◽  
Operational Environment ◽  
Low Aspect Ratio

This paper covers a class of actuators for modern high speed, high performance subscale aircraft. The paper starts with an explanation of the challenges faced by micro aircraft, including low power, extremely tight volume constraints, and high actuator bandwidth requirements. A survey of suitable actuators and actuator materials demonstrates that several classes of piezoceramic actuators are ideally matched to the operational environment. While conventional, linear actuation of piezoelectric actuators can achieve some results, dramatic improvements via reverse-biased spring mechanisms can boost performance and actuator envelopes by nearly an order of magnitude. Among the highest performance, low weight configurations are post-buckled precompressed (PBP) actuator arrangements. Analytical models display large deflections at bandwidths compatible with micro aircraft flight control speed requirements. Bench testing of an example PBP micro actuator powered low aspect ratio flight control surface displays +/−11° deflections through 40 Hz, with no occupation of volume within the aircraft fuselage and good correlation between theory and experiment. A wind tunnel model of an example high speed micro aircraft was fabricated along with low aspect ratio PBP flight control surfaces, demonstrating stable deflection characteristics with increasing speed and actuator bandwidths so high that all major aeromechanical modes could be easily controlled. A new way to control such a PBP stabilator with a Limit Dynamic Driver is found to greatly expand the dynamic range of the stabilator, boosting the dynamic response of the stabilator by more than a factor of four with position feedback system engaged.

Sign in / Sign up

Export Citation Format

Share Document