scholarly journals Thermal performance deterrence caused by PCM inclusion in firefighting garments: The other side of the story

2021 ◽  
Vol 2116 (1) ◽  
pp. 012018
Author(s):  
A Fonseca ◽  
S F Neves ◽  
J B L M Campos
Keyword(s):  
Heat Flux ◽  
Phase Change ◽  
Melting Temperature ◽  
Latent Heat ◽  
Thermal Performance ◽  
Heat Exposure ◽  
Negative Influence ◽  
High Heat Flux ◽  
Fire Exposure ◽  
Skin Damage

Abstract Firefighters usually encounter high heat flux exposures, which can cause severe burns. The addition of a phase change material (PCM) layer into a firefighting garment assembly has proven to be beneficial as it lowers the garments temperature during the fire exposure. However, after the fire exposure, accumulated heat in the PCM garment is discharged towards skin and environment which can have a negative influence on thermal performance. In this study, a one dimensional numerical approach was used to study the effect of environment parameters (ambient convective heat flux) as well as PCM parameters (latent heat, melting temperature) on the thermal performance of the firefighting garment, after the fire exposure. It was concluded that the amount and phase change temperature at which latent heat is discharged had a significant effect on thermal performance, depending on the heat exposure scenario. For high – intensity exposures, skin damage is promoted by an increase in both properties whilst for low intensity exposures, a decrease in melting temperature would promote greater skin damage. The results outlined in this paper could aid in the manufacture of PCM firefighting garments, as skin damage due to PCM resolidification might be an important parameter to take into account when maximizing thermal performance.

Spray Cooling for Time Resolved Emission Measurements of ICs

2004 ◽  
Author(s):  
Rama R. Goruganthu ◽  
David Bethke ◽  
Shawn McBride ◽  
Tom Crawford ◽  
Jonathan Frank ◽  
...  
Keyword(s):  
Heat Flux ◽  
Thermal Performance ◽  
Flip Chip ◽  
Cooling System ◽  
Spray Cooling ◽  
Junction Temperature ◽  
Maximum Temperature ◽  
Uniform Heat Flux ◽  
High Heat Flux ◽  
Time Resolved

Abstract Spray cooling is implemented on an engineering tool for Time Resolved Emission measurements using a silicon solid immersion lens to achieve high spatial resolution and for probing high heat flux devices. Thermal performance is characterized using a thermal test vehicle consisting of a 4x3 array of cells each with a heater element and a thermal diode to monitor the temperature within the cell. The flip-chip packaged TTV is operated to achieve uniform heat flux across the die. The temperature distribution across the die is measured on the 4x3 grid of the die for various heat loads up to 180 W with corresponding heat flux of 204 W/cm2. Using water as coolant the maximum temperature differential across the die was about 30 °C while keeping the maximum junction temperature below 95 °C and at a heat flux of 200 W/cm2. Details of the thermal performance of spray cooling system as a function of flow rate, coolant

Heat Transfer Enhancement in Compact Phase Change Microchannel Heat Exchangers for High Flux Laser Diodes

2018 ◽  
Author(s):  
Jensen Hoke ◽  
Todd Bandhauer ◽  
Jack Kotovsky ◽  
Julie Hamilton ◽  
Paul Fontejon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Flow Boiling ◽  
Laser Diodes ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Average Maximum

Liquid-vapor phase change heat transfer in microchannels offers a number of significant advantages for thermal management of high heat flux laser diodes, including reduced flow rates and near constant temperature heat rejection. Modern laser diode bars can produce waste heat loads >1 kW cm−2, and prior studies show that microchannel flow boiling heat transfer at these heat fluxes is possible in very compact heat exchanger geometries. This paper describes further performance improvements through area enhancement of microchannels using a pyramid etching scheme that increases heat transfer area by ∼40% over straight walled channels, which works to promote heat spreading and suppress dry-out phenomenon when exposed to high heat fluxes. The device is constructed from a reactive ion etched silicon wafer bonded to borosilicate to allow flow visualization. The silicon layer is etched to contain an inlet and outlet manifold and a plurality of 40μm wide, 200μm deep, 2mm long channels separated by 40μm wide fins. 15μm wide 150μm long restrictions are placed at the inlet of each channel to promote uniform flow rate in each channel as well as flow stability in each channel. In the area enhanced parts either a 3μm or 6μm sawtooth pattern was etched vertically into the walls, which were also scalloped along the flow path with the a 3μm periodicity. The experimental results showed that the 6μm area-enhanced device increased the average maximum heat flux at the heater to 1.26 kW cm2 using R134a, which compares favorably to a maximum of 0.95 kw cm2 dissipated by the plain walled test section. The 3μm area enhanced test sections, which dissipated a maximum of 1.02 kW cm2 showed only a modest increase in performance over the plain walled test sections. Both area enhancement schemes delayed the onset of critical heat flux to higher heat inputs.

scholarly journals Capillary-Limited Evaporation From Well-Defined Microstructured Surfaces

2013 ◽  
Author(s):  
Solomon Adera ◽  
Rishi Raj ◽  
Evelyn N. Wang
Keyword(s):  
Thin Film ◽  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Thermal Management ◽  
Latent Heat ◽  
Thin Film Evaporation ◽  
Film Evaporation ◽  
Microstructured Surfaces ◽  
Latent Heat Of Vaporization

Thermal management is increasingly becoming a bottleneck for a variety of high power density applications such as integrated circuits, solar cells, microprocessors, and energy conversion devices. The performance and reliability of these devices are usually limited by the rate at which heat can be removed from the device footprint, which averages well above 100 W/cm2 (locally this heat flux can exceed 1000 W/cm2). State-of-the-art air cooling strategies which utilize the sensible heat are insufficient at these large heat fluxes. As a result, novel thermal management solutions such as via thin-film evaporation that utilize the latent heat of vaporization of a fluid are needed. The high latent heat of vaporization associated with typical liquid-vapor phase change phenomena allows significant heat transfer with small temperature rise. In this work, we demonstrate a promising thermal management approach where square arrays of cylindrical micropillar arrays are used for thin-film evaporation. The microstructures control the liquid film thickness and the associated thermal resistance in addition to maintaining a continuous liquid supply via the capillary pumping mechanism. When the capillary-induced liquid supply mechanism cannot deliver sufficient liquid for phase change heat transfer, the critical heat flux is reached and dryout occurs. This capillary limitation on thin-film evaporation was experimentally investigated by fabricating well-defined silicon micropillar arrays using standard contact photolithography and deep reactive ion etching. A thin film resistive heater and thermal sensors were integrated on the back side of the test sample using e-beam evaporation and acetone lift-off. The experiments were carried out in a controlled environmental chamber maintained at the water saturation pressure of ≈3.5 kPa and ≈25 °C. We demonstrated significantly higher heat dissipation capability in excess of 100 W/cm2. These preliminary results suggest the potential of thin-film evaporation from microstructured surfaces for advanced thermal management applications.

scholarly journals Thermal Assessment of Nano-Particulate Graphene-Water/Ethylene Glycol (WEG 60:40) Nano-Suspension in a Compact Heat Exchanger

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1929 ◽  
Author(s):  
M. Sarafraz ◽  
Mohammad Safaei ◽  
Zhe Tian ◽  
Marjan Goodarzi ◽  
Enio Bandarra Filho ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Ethylene Glycol ◽  
Thermal Performance ◽  
Evaluation Criteria ◽  
High Heat ◽  
Operating Conditions ◽  
Working Fluid ◽  
High Heat Flux ◽  
Micro Channel

In the present study, we report the results of the experiments conducted on the convective heat transfer of graphene nano-platelets dispersed in water-ethylene glycol. The graphene nano-suspension was employed as a coolant inside a micro-channel and heat-transfer coefficient (HTC) and pressure drop (PD) values of the system were reported at different operating conditions. The results demonstrated that the use of graphene nano-platelets can potentially augment the thermal conductivity of the working fluid by 32.1% (at wt. % = 0.3 at 60 °C). Likewise, GNP nano-suspension promoted the Brownian motion and thermophoresis effect, such that for the tests conducted within the mass fractions of 0.1%–0.3%, the HTC of the system was improved. However, a trade-off was identified between the PD value and the HTC. By assessing the thermal performance evaluation criteria (TPEC) of the system, it was identified that the thermal performance of the system increased by 21% despite a 12.1% augmentation in the PD value. Furthermore, with an increment in the fluid flow and heat-flux applied to the micro-channel, the HTC was augmented, showing the potential of the nano-suspension to be utilized in high heat-flux thermal applications.

scholarly journals Experimental Study on Thermal Performance of a Bent Copper-Water Heat Pipe

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Shuangshuang Miao ◽  
Jiajia Sui ◽  
Yulong Zhang ◽  
Feng Yao ◽  
Xiangdong Liu
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Critical Heat Flux ◽  
Working Conditions ◽  
Thermal Performance ◽  
Heat Input ◽  
High Heat ◽  
High Heat Flux ◽  
Electronic Components ◽  
Copper Water

Vapor-liquid phase change is regarded as an efficient cooling method for high-heat-flux electronic components. The copper-water bent heat pipes are particularly suited to the circumstances of confined space or misplaced heat and cold sources for high-heat-flux electronic components. In this paper, the steady and transient thermal performance of a bent copper-water heat pipe is studied based on a performance test system. The effects of cooling temperature, working conditions on the critical heat flux, and equivalent thermal conductivity have been examined and analyzed. Moreover, the influences of heat input and working conditions on the thermal response of a bent heat pipe have also been discussed. The results indicate that the critical heat flux is enhanced due to the increases in cooling temperature and the lengths of the evaporator and condenser. In addition, the critical heat flux is improved by extending the cooling length only when the operating temperature is higher than 50°C. The improvement on the equivalent thermal by increasing the heating length is more evident than that by increasing cooling length. It is also demonstrated by the experiment that the bent copper-water heat pipe can respond quickly to the variation of heat input and possesses superior transient heat transfer performance.

Thermal Performance Study of VPS-W Coatings on CuCrZr Under High Heat Flux

2007 ◽  
Vol 9 (3) ◽  
pp. 261-264 ◽  
Author(s):  
Chong Fali ◽  
Chen Junling ◽  
Li Jiangang ◽  
Zheng Xuebin ◽  
Ding Chuanxian
Keyword(s):  
Heat Flux ◽  
Thermal Performance ◽  
High Heat ◽  
High Heat Flux ◽  
Performance Study

10310 A study on high heat flux heat removal with phase change using a porous metal

2014 ◽  
Vol 2014.20 (0) ◽  
pp. _10310-1_-_10310-2_
Author(s):  
Daiki Hanzawa ◽  
Kyosuke Katsumata ◽  
Tomio Okawa
Keyword(s):  
Heat Flux ◽  
Phase Change ◽  
Heat Removal ◽  
Porous Metal ◽  
High Heat ◽  
High Heat Flux
Sign in / Sign up

Export Citation Format

Share Document